What does it mean to schedule two sessions for Subject 1?

1 Answers
SanArianna
07/28/25 8:40pm
Subject 1 scheduling two sessions means that if you fail the first exam, you have another opportunity to retake it. The following is a detailed introduction to the Subject 1 exam: 1. Overview: Subject 1, also known as the Subject 1 theory test or driver theory test, is part of the motor vehicle driver's license assessment. According to the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," the exam content includes driving theory basics, road safety laws and regulations, local regulations, and related knowledge. 2. Others: Students can use driver simulation test software on mobile or computer devices to study traffic regulations. The exam papers are randomly selected and combined by the computer driver exam system according to the proportion specified in the "Motor Vehicle Driver's License Work Specifications."
Was this review help?
14
0
Share
More Forum Discussions

Does Storing Engine Oil in the Trunk in Summer Have Any Impact?

Storing engine oil in the trunk during summer has no impact. Engine oil is heat-resistant, as the engine operates at around 100 degrees Celsius, while the temperature in the trunk is far below this level. Engine oil is not classified as a hazardous material and is not flammable, so it does not need to comply with hazardous material transportation and storage regulations and can be safely stored in the trunk. However, lubricants are still chemical products, so safe storage and transportation should be ensured to avoid environmental pollution. Below is some related information about engine oil: Properties of Lubricating Oil: Firstly, it does not have flammable characteristics and can only be classified as a combustible material. Secondly, it does not have strong corrosiveness; it is not highly volatile; it does not have packaging difficulties; and it does not have storage or transportation challenges. Functions of Engine Oil: Engine oil has a lubricating effect. There is rapid relative sliding between the piston and cylinder, as well as between the crankshaft and bearing shells. To prevent excessive wear of parts, an oil film needs to be established between the two sliding surfaces. A sufficiently thick oil film separates the surfaces of the relatively sliding parts.
20
1
Share

What is the disassembly method for the USB port of the Arrizo 5?

The disassembly method for the USB port of the Arrizo 5 is as follows: 1. Remove the cover and take out the screws; 2. Use your fingers to grip the cover under the gear shift lever and gently lift it upwards to remove the cover; 3. Unscrew the two screws, take out the storage rack, disconnect the cigarette lighter and USB connection wires, and then unscrew the two screws. The main function of the USB port is to utilize the standard power supply in the car to charge DC 5V electrical devices via the USB interface or serve as a fixed power supply interface for electrical devices. The 2021 Luxury model of the Arrizo 5 features a MacPherson strut independent front suspension and a torsion beam non-independent rear suspension. It is equipped with a 1.6L naturally aspirated engine, delivering a maximum horsepower of 90 PS, a maximum power of 66 kW, and a maximum torque of 130 Nm, paired with a 5-speed manual transmission.
14
5
Share

How Long After Applying Chassis Armor Can You Drive

Generally, you should wait at least 7 days after applying chassis armor before driving the vehicle. Below is some knowledge about chassis armor: Precautions for chassis armor application: Before applying chassis armor, it's essential to thoroughly clean the chassis and fender areas where the application will occur. Always choose a reputable service provider to remove all four tires. Properly shield the exhaust pipe and wheels during application. Avoid washing the car for three days after installation. Functions of chassis armor: Impact protection: While driving, road debris can inevitably strike and damage the vehicle's undercarriage. Anti-scraping: On various road surfaces, protruding objects may cause wear to the chassis. Corrosion resistance: In southern regions with frequent rainfall, acid rain can easily splash onto the chassis, leading to corrosion over time. Heat insulation: During hot summers, extreme ground temperatures can transfer heat through the chassis into the cabin. Noise reduction: When driving on highways, tire-road friction noise increases with speed. A well-protected undercarriage significantly reduces interior noise levels.
17
5
Share

How to troubleshoot the engine warning light?

To troubleshoot the engine warning light, follow these steps: 1. Check the spark plugs and cylinder wires. 2. Perform a fuel pressure system test. 3. Inspect the fuel injectors for each cylinder. 4. Examine the fuel pump and its circuit. 5. Check the cylinder pressure, intake and exhaust valve clearance, fuel vapor control solenoid valve, EGR valve cylinder operation, and whether the intake manifold is leaking. If the warning light appears on the dashboard while driving, try the following steps: 1. Pull over and turn off the engine for 5-10 minutes. Without pressing the brake, press the start button or turn the key halfway to the 'on' position without engaging the clutch. The car will perform a self-check upon powering up. Wait 5-10 seconds to see if the warning light turns off. 2. If other warning lights remain on, take the car to a 4S shop or repair shop to check the relevant modules and parts. If only the engine warning light stays on, restart the engine and observe if it remains lit. 3. If the engine warning light turns off, no further action is needed. If it stays on, take the car to a 4S shop or repair shop to inspect the engine-related components and modules.
20
4
Share

What causes car windows to fog up in the rain?

The reason car windows fog up in the rain is due to high air humidity and significant temperature differences between the inside and outside of the glass, causing water vapor to condense on the glass. The solutions are: 1. Use the air conditioning defogging function by turning on the front window defogging mode, increasing the fan speed, and lowering the temperature; 2. Activate the one-touch defogging function; 3. Increase air convection by opening windows to reduce the temperature difference inside and outside the car, thereby weakening the conditions for fog formation; 4. In winter, use the air conditioning's hot air defogging function. Do not turn on the air conditioning immediately after starting the car. Wait a few minutes for the engine to warm up and the water temperature to rise, then start heating, increase the fan speed, and turn on the front window defogging mode; 5. Spray defogging agent evenly on the glass surface and wipe it clean with a dry towel; 6. Make a homemade defogging solution by mixing dish soap and water in a 1:6 ratio in a bottle. Spray and wipe before driving; the effect is similar to commercial defogging agents, though the duration is slightly shorter.
9
1
Share

What is the method to remove film without damaging heating wires?

The method to remove film without damaging heating wires is to use a hard card: Use your fingernail or a hard card like a bank card to lift one corner of the car film. If that doesn't work, use a wallpaper knife. During the operation, avoid rough handling and spray water beforehand to moisten the area. Issues with film removal: Adhesive residue, as the film is glued to the glass, makes thorough cleaning quite troublesome. Since the rear windshield area contains the radio's window antenna and heating wires, there's a 50% chance of breakage during adhesive removal. The amount of water required for film replacement is 5–10 times that of normal film application, increasing the actual risk of water damage to electrical components by more than 10 times. Some shops use blades for adhesive removal, with a 50% chance of scratching the glass. Functions of car film: Preventing glass shattering. Generally, car film adds a layer of strong and flexible protection to the glass, so even if the glass breaks in an accident, the film remains to protect, preventing glass fragments from scattering and adding an extra layer of safety. Ensuring safety. It not only enhances vehicle safety but also protects personal safety. However, the quality of car films on the market varies greatly, so it's essential to recognize quality and purchase carefully.
1
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.