What does it mean to replenish automotive glass cleaning fluid?

How to reset the Toyota Crown tire pressure warning light?

With the ignition switch turned on, press and hold the tire pressure warning reset switch (RESET button) until the LOW TIRE light starts flashing, then release it. The following are the hazards of low tire pressure: 1. Fuel consumption: The friction coefficient with the road surface increases, leading to higher fuel consumption. 2. Steering wheel: Causes the steering wheel to become heavy and prone to deviation, which are factors detrimental to driving safety. 3. Tire bead: Reduces the functionality of the cords and rubber, leading to delamination or cord breakage, excessive friction with the rim, causing damage to the bead area and abnormal wear. 4. Tire: Increases the movement of various parts of the tire, multiplies the friction between the tire and the ground, sharply raises the tire temperature, softens the tire, and drastically reduces its strength. High-speed driving may result in a tire blowout.

17

5

Share

Does Closing the Exhaust Valve Damage the Car?

Closing the exhaust valve can damage the car. Here are some related details about exhaust valves: Resistant to Deformation: The float of the exhaust valve is made of low-density PP material, which does not deform even after prolonged immersion in high-temperature water. This ensures smooth movement of the float. Resistant to Rust: The float lever is made of hard plastic, and the connections between the lever, float, and support are designed with movable joints, preventing rust formation during long-term operation, which could otherwise lead to system failure and water leakage. The sealing end of the lever is supported by a spring, allowing it to extend and retract with the lever's movement, ensuring a tight seal when not exhausting.

3

2

Share

Should the headlights be adjusted to 0 or 4?

Whether to adjust the car headlights to 0 or 4 depends on the driving conditions and the adjustment of the front headlight axis. If driving without heavy loads, luggage, or on flat roads, choose the normal position "0". If the number of passengers and the load or luggage in the car changes, the front headlight axis will be higher than the normal position. To adjust to the appropriate beam height, the higher the number marked on the corresponding switch, the lower the front headlight axis will be. Method for adjusting car headlights: Find a wall, ensure the ground is level, and park the car about 10 meters away from the wall. Measure the height from the ground to the center of the headlights and the distance between the two headlights. Place a horizontal masking tape on the wall 0.1 meters lower than the headlights, ensuring the tape is centered directly in front of the car. Turn on the headlights and adjust the vertical adjustment screw until the headlight beam is centered on the tape on the wall. Continue adjusting the vertical adjustment screw until the headlight beam is straight ahead. To ensure the adjustment is correct, measure the height of the beam on the wall and the height of the headlights to confirm they are equal. Precautions for using car lights: When a motor vehicle passes through an intersection controlled by traffic lights and turns left, the turn signal should be activated, and the low beam should be used at night. During periods when streetlights are on, or when driving in low visibility conditions such as fog, rain, snow, dust, or hail, the headlights, position lights, and rear lights should be turned on. When a following vehicle is driving close to the vehicle in front in the same direction, the high beam should not be used.

13

4

Share

Is the 'Bang' Sound When Pulling the Handbrake a Sign of Breakage?

It is not broken. The sound occurs when the brake pads adhere to the brake discs. Lightly tapping the brakes a few times after starting the car will resolve the issue. Sometimes, this situation can also occur if the car is left unused after washing and driven the next day. Below are specific details about the handbrake: 1. Handbrake: The handbrake operates on the lever principle, using a steel cable to activate the rear wheel braking mechanism. The key components are the locking pawl and gear, which automatically engage together. 2. Pulling the Handbrake (Braking the Rear Wheels): When the handle is pulled, the pawl automatically springs up to catch the next gear tooth, while the connected steel cable gradually tightens, thereby applying the rear wheel brake pads. 3. Releasing the Handbrake (Releasing the Rear Wheels): When the handle button is pressed, the pawl and gear separate. Pressing down the handle then loosens the tightened steel cable, releasing the rear wheel brakes.

11

2

Share

Where is the anti-theft control box located in the Buick Excelle?

Buick Excelle's anti-theft control box is located at the lower left corner of the steering wheel, and the key induction coil on the steering column is the anti-theft module. Purpose of installing the anti-theft device: The main purpose of installing the anti-theft central locking system is to control the vehicle's original central locking, achieving the goal of remote lock/unlock operation. Function of the anti-theft device: The vehicle anti-theft control system integrates the anti-theft device with power windows and central door lock control modules for centralized monitoring. When pressing the lock button on the remote control, the central door lock system engages. When the system enters alarm status, the door windows will automatically rise to prevent users from forgetting to close them, eliminating concerns about rain, wind, or theft, thus providing convenience for users.

11

3

Share

Does a Small Gear Driving a Large Gear Speed Up or Slow Down?

A small gear driving a large gear results in a reduction in speed. When a small gear drives a large gear, the rotational speed decreases, which is based on the principle of gear ratio. When two gears of different diameters mesh and rotate together, the larger diameter gear naturally turns slower than the smaller one. The speed ratio is inversely proportional to the gear diameters. Below are the specific functions of gear engagement: 1. Changing speed or torque: There are many gears in the transmission and drivetrain. The gears in the transmission are used to change speed and torque, while the main reduction gear in the differential reduces speed and increases torque. 2. Power transmission: Gears serve a power transmission function. Many four-wheel-drive vehicles have numerous gears in the transfer case, which facilitate power transmission. The main reduction gear in the differential also aids in power transmission. Many gears transmit power by meshing with each other. Gears in the steering system also contribute to power transmission. 3. Achieving gear ratios: Different gear combinations in the transmission enable various gear ratios, allowing the vehicle to adapt to different driving conditions.

2

3

Share

What does it mean to replenish automotive glass cleaning fluid?

How to reset the Toyota Crown tire pressure warning light?

Does Closing the Exhaust Valve Damage the Car?

Should the headlights be adjusted to 0 or 4?

Is the 'Bang' Sound When Pulling the Handbrake a Sign of Breakage?

Where is the anti-theft control box located in the Buick Excelle?

Does a Small Gear Driving a Large Gear Speed Up or Slow Down?

What is the first maintenance mileage for the Volvo XC60?

How Long is the Battery Life of BYD Cars?

Is There Any Impact If a Car Stalls in Water and Restarts?

Where is the center console?