What does it mean to meet an oncoming vehicle?

1 Answers
MacReid
07/30/25 1:54am
When an oncoming vehicle passes by your vehicle at a certain point while traveling in the opposite direction, it is referred to as your vehicle meeting that oncoming vehicle. Here is some relevant information: 1. Key elements for safe vehicle meeting: Meeting vehicles is an inevitable situation every driver encounters during driving. Drivers must comply with traffic regulations and consciously practice the "three priorities of courtesy," namely "yield first, slow down first, stop first." Before meeting, drivers should assess the traffic situation, including the oncoming vehicle and road conditions, choose an appropriate meeting point, pass on the right, and ensure safe vehicle meeting. 2. Precautions: When meeting vehicles on a two-lane road without a median barrier, first reduce speed, then move to the right, control the speed, steady the steering wheel, and pay attention to the conditions on both sides of the road to ensure sufficient lateral spacing during the meeting.
Was this review help?
6
1
Share
More Forum Discussions

How to Adjust Valves on an 8-Cylinder Engine?

8-cylinder engine valve clearance adjustment is performed according to the firing order of 1-5-4-2-6-3-7-8. Valves are responsible for introducing air into the engine and expelling exhaust gases after combustion. Structurally, they are divided into intake valves and exhaust valves. Below are the specific adjustment steps: 1. First, bring cylinder 1 to top dead center (TDC), then adjust the intake and exhaust valves of cylinder 1, the exhaust valves of cylinders 5, 4, and 2, leave cylinder 6 unchanged, and adjust the intake valves of cylinders 3, 7, and 8. 2. Next, rotate the crankshaft 360 degrees to bring cylinder 6 to top dead center, then adjust the intake and exhaust valves of cylinder 6, the exhaust valves of cylinders 3, 7, and 8, leave cylinder 1 unchanged, and adjust the intake valves of cylinders 5, 4, and 2.
1
5
Share

What's the reason for high coolant temperature?

The full name of antifreeze is antifreeze coolant, meaning it has the function of preventing freezing. Antifreeze can prevent the coolant from freezing and cracking the radiator or damaging the engine cylinder block or head when parking in cold winters. There are three main reasons for high coolant temperature: 1. Improper addition and replacement of antifreeze: This can cause early blockage of the engine water passages and radiator, leading to high water temperature. Antifreeze should be replaced every two years, and only original antifreeze should be used during replacement and addition. If the concentration is too high, it can result in poor heat dissipation and engine overheating. 2. Leakage in the cooling system components: If there are leaks in the cylinder block, cylinder head, cylinder gasket, heater radiator, water pipes, rubber hoses, or drain switch, it will reduce the water volume and decrease the ability to absorb heat energy from the cylinder, causing the coolant temperature to rise excessively. 3. Air in the pipes, idling operation.
18
2
Share

What lights should be used when driving on roads with streetlights at night?

When driving on roads with streetlights at night, low beam headlights should be used. On roads without streetlights or highways, high beam headlights and clearance lights should be turned on, maintaining a safe speed and paying attention to road conditions for safe passage. When approaching intersections, reduce speed and switch between high and low beams to alert vehicles and pedestrians. When driving at night on roads without streetlights, with poor lighting, or in low visibility conditions such as fog, rain, snow, or dust, high beam headlights should not be used when a vehicle is closely following another in the same direction. On roads without central barriers or center lines, high beams should not be used within 150 meters of an oncoming vehicle. High beam headlights should not be used when meeting non-motorized vehicles on narrow bridges or roads without central barriers or center lines. When passing sharp curves, slopes, arched bridges, crosswalks, or intersections without traffic signals, alternate between high and low beams to signal.
7
5
Share

What lights to use when meeting on narrow roads or bridges at night

It is best to alternately use high and low beams when driving through narrow roads or bridges at night. According to Articles 48, 51, and 58 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China", when meeting another vehicle at night, switch to low beam when the oncoming vehicle is more than 150 meters away. When a motor vehicle passes through an intersection controlled by traffic lights at night, use low beam when turning. When a following vehicle is driving close to the vehicle in front in the same direction, use low beam. Drive with low beam on well-lit roads. When a motor vehicle passes through sharp curves, slopes, arch bridges, crosswalks, or intersections without traffic light control at night, alternately use high and low beams to signal. When driving in low visibility conditions such as fog, rain, snow, dust, or hail, turn on the headlights, position lights, and rear lights. Turn on fog lights and hazard warning flashers when driving in foggy conditions. Do not turn on fog lights when driving in normal weather conditions at night, as fog lights can be very dazzling to oncoming drivers. Do not use high beam when driving in fog, as the upward-angled high beam light gets diffusely reflected by the fog, creating a blinding white haze in front of the vehicle that actually reduces visibility.
14
1
Share

What is the average fuel consumption per 100 kilometers for a sedan?

The average fuel consumption per 100 kilometers for a sedan is approximately 1.68 liters. Below are the fuel consumption calculation formula and tips for reducing fuel consumption: Fuel consumption calculation formula: Fuel consumed ÷ Distance traveled × 100 = Fuel consumption per 100 kilometers. The data on fuel consumed is relatively difficult to obtain, so the initial data is usually taken from a full tank. After driving a certain distance, the tank is refilled, and the fuel amount provided by the gas station is used as the accurate data. Tips for reducing fuel consumption: The economic speed is the speed at which the car consumes the least fuel when driving in direct gear or overdrive. When a car travels on the same road, different speeds result in different fuel consumption. Therefore, there is a specific speed at which fuel consumption is the lowest. Thus, the car should be driven at a moderate speed in direct gear or high gear to save fuel.
5
0
Share

Should Regular Cars Use 92 or 95 Octane Fuel?

The selection of fuel grade should be based on the compression ratio of the car's engine. The appropriate fuel grade for the vehicle is usually indicated on the inside of the fuel tank cap. If it specifies 92 octane fuel, then use 92. If it specifies 95 octane fuel, then use 95. Whether the fuel is labeled 92 or 95, the number represents the fuel's anti-knock performance. The higher the fuel grade, the better the anti-knock performance, but this has little to do with the quality of the gasoline itself. It is not necessarily true that higher fuel grades are always better, as many car owners commonly believe. For naturally aspirated engines, 92 octane fuel is generally recommended. Higher-grade fuel has better anti-knock performance but burns relatively slower, which can lead to a higher compression ratio in the engine, resulting in reduced power and increased temperature. For turbocharged engines, the manufacturer usually recommends fuel with a grade of 92 or higher. Using 95 octane fuel not only helps achieve higher torque at low speeds but also reduces engine vibration and noise.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.