What does it mean to drive not according to regulations in Subject 3?

Does Low Washer Fluid Affect Driving?

Low washer fluid does not have a significant impact on driving, but insufficient car washer fluid may affect driving safety. In dusty environments or when driving on highways during rain, if the windshield becomes blurry and there is no washer fluid, using the wipers alone will not clean the windshield effectively, posing a major safety hazard. Additional Information: Below are some details about washer fluid: 1. Regular Checks: In dusty environments or when driving on highways during rain, washer fluid is consumed very quickly. It is safest to perform regular checks and keep spare washer fluid in the car for easy refilling when needed. 2. Refilling Notes: Car washer fluid is a consumable item in vehicle use. If you run out, you can purchase and refill it yourself or visit a 4S shop or repair shop for assistance. Avoid using plain water directly, as it can damage the wipers and glass. 3. Consequences of No Washer Fluid: Continuously operating the washer fluid lever without fluid can cause the motor to overheat, leading to expensive repair costs.

15

0

Share

How to Remove the Rear Seat of an Old Santana?

The method to remove the rear seat of an old Santana: First, lift the rear seat cushion upwards with force to detach it. Then, proceed to remove the backrest. To remove the backrest, you need to pull out the lifting lever at the top first, which will allow you to take off the rear seat. Taking the 2013 Santana as an example, the car measures 4473mm in length, 1706mm in width, and 1469mm in height, with a wheelbase of 2603mm. It is a 4-door, 5-seater sedan equipped with a 5-speed manual transmission. It is powered by a 1.4L L4 naturally aspirated engine, delivering a maximum horsepower of 90ps, a maximum torque of 132nm, a maximum power of 66kw, and a top speed of 181km/h.

17

2

Share

What Causes Air Brake Failure?

Reasons for air brake failure include insufficient air pressure in the braking system, suggesting inspection of pipelines and the air pressure pump; it may also be due to excessive brake clearance, recommending adjustment of brake pad clearance. Below is relevant content introduction: 1. Parking Brake: Conventional parking brakes lock the drive shaft, while foot brakes use compressed air entering the brake chamber to lock the wheels. The parking brake fails when there is a mechanical fault in the parking brake or drive shaft; the foot brake fails when there is a fault in any part of the air pump, pipeline, air reservoir, or brake valve. The air break brake can effectively avoid these dangers. 2. Before Starting: Before starting the vehicle, the control lever of the manual valve should be moved back to the position that releases the parking brake, allowing compressed air from the parking brake air reservoir to fill the parking brake chamber.

5

2

Share

Will There Be a Jerking Sensation When Accelerating and Decelerating at Low Speeds?

There is a jerking sensation when accelerating and decelerating at low speeds. Below are detailed explanations: 1. Reasons: Clean engine carbon deposits, check the oxygen sensor, and regularly replace the three filters. 2. Content: When driving at low speeds, the jerking sensation is noticeable during acceleration and deceleration. Cleaning engine carbon deposits is essential; excessive carbon buildup can be addressed by adding a certain amount of cleaner during refueling and driving at high speeds for a period, which helps increase exhaust flow and carry away carbon particles. Checking the oxygen sensor is crucial as it monitors the air-fuel ratio in the engine. A damaged oxygen sensor can disrupt the air-fuel ratio, leading to a sudden increase in fuel consumption. If the oxygen sensor is faulty, the vehicle will emit darker exhaust gases from the tailpipe during driving, indicating the need for replacement.

15

3

Share

The Hazards of Lift Blocks for Off-Road Vehicles?

The disadvantage of lift blocks for off-road vehicle chassis is their impact on vehicle stability. Below is an introduction to lift blocks for off-road vehicle chassis: 1. Impact of chassis height: Vehicles with higher chassis have better off-road performance, but raising the chassis also raises the center of gravity, increasing centrifugal force during turns and reducing stability at high speeds. Conversely, lowering the chassis can counteract centrifugal force during high-speed turns, making low chassis more suitable for high-speed driving. 2. Introduction to chassis height: The height of a vehicle's chassis, technically known as ground clearance, is defined as the distance between the ground and the lowest rigid point of the vehicle under full load. Low ground clearance can lead to scraping the chassis or damaging the oil pan when driving on rough roads or over speed bumps. Adequate ground clearance ensures smooth passage during transport and reduces the risk of scraping when driving onto curbs.

5

2

Share

How to Use Mazda's Autohold Function?

This function works in conjunction with the driver's seatbelt and will not activate if the driver is not wearing it. First, fasten the seatbelt in the driver's seat. When the "AUTO-HOLD" button is pressed, the corresponding automatic parking function will activate. At traffic lights, you can relax your right foot without stepping on the brake, as the "AUTO-HOLD" function will help keep the car stationary, preventing it from rolling. Below are the relevant details: 1. Principle. Traditional handbrakes require the driver to manually release the handbrake or skillfully coordinate the throttle and clutch for a smooth start on slopes. During startup, the parking control unit calculates information from sensors such as the clutch distance sensor, clutch engagement speed sensor, and throttle pedal sensor to ensure a smooth start. 2. Activation. Press the AUTO-HOLD button to enable the automatic parking function, which automatically activates four-wheel braking when stopping at traffic lights or parking. Even in D or N gear, there's no need to keep your foot on the brake or use the handbrake; the vehicle remains stationary. 3. Deactivation. To release the stationary state, lightly press the throttle to disengage the brake.

20

1

Share

What does it mean to drive not according to regulations in Subject 3?

Does Low Washer Fluid Affect Driving?

How to Remove the Rear Seat of an Old Santana?

What Causes Air Brake Failure?

Will There Be a Jerking Sensation When Accelerating and Decelerating at Low Speeds?

The Hazards of Lift Blocks for Off-Road Vehicles?

How to Use Mazda's Autohold Function?

Where is the engine number of the Changan Ford Focus located?

How to Turn on the High Beam of the New Santana?

What is valve clearance?

What are the differences between the Mercedes-Benz V-Class and the Vito?