···
Log in / Register

What does 'Exam Appointment First Session 26' mean?

4 Answers
RicardoLee
07/28/25 6:54pm

Exam Appointment First Session 26 refers to the serial number 26. Here is some extended information: 1. Exam Appointment First Session: The first session refers to the first batch of examinees who will enter the examination area following the examiner's instructions. The second session refers to the second batch of examinees who will enter after the first session is completed. This examination method is implemented due to the large number of examinees, to facilitate the management of examination order and the recording of examination results. Confirm your examination time based on your session to avoid prolonged waiting outside the examination area and overcrowding. 2. Teaching Objectives: Master the basic driving operation essentials, possess the fundamental ability to control the vehicle, proficiently grasp the basic methods of driving in the venue and on the road, have the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and be able to accurately control the vehicle's driving position, speed, and route.

Was this review help?
15
2
Share
RhettFitz
08/11/25 10:48pm

Last time I booked a driving test, I encountered a similar symbol. 'First Session 26' is likely a code in the driving test system, referring to the first scheduled test session, where '26' could mean the 26th day or session number 26. New drivers often worry about booking confusion. I panicked and checked the app details to confirm it was the 8 AM session at Lane 26. The system often simplifies displays, omitting dates or months, so you need to tap to expand for full information. Missing a session means rescheduling a month later, wasting time and money. I recommend arriving half an hour early to familiarize yourself with the test site, bringing your ID and booking confirmation to avoid the chaos I experienced. Driving test bookings require attention to detail—a small oversight could mean a wasted trip, so double-check before submitting.

Was this review help?
6
1
Share
Expand All
LunaAnn
09/30/25 4:36am

Understanding the codes is crucial when booking your test. 'First Session 26' usually refers to the first time slot of the driving test, such as the morning session, and '26' might indicate the candidate's position number or the floor level of the test center. When I was getting my driver's license, the system always used such abbreviations, and it could be confusing if you're not familiar with them. Before making an appointment, make sure to thoroughly read the driving school's guide or simulate the process on the official website a few times to understand the meaning of each field. Remember, test slots are in high demand, so you need to be quick when securing a session—using a mobile app is often more reliable than a computer. Missing the first session could delay your progress by weeks, affecting your license issuance date. In short, stay calm. There are usually small question marks in the corners of the booking page explaining the symbols. Explore a bit more and don’t be as hasty as I was when I first started—random clicks might lead to missed opportunities and regret later.

Was this review help?
17
4
Share
Expand All
McHadley
11/13/25 6:28am

I usually enjoy delving into car-related matters. 'First Session 26' in the exam reservation simply refers to the batch number or date of the first exam. This kind of marking is common in driving test systems, where 'First Session' indicates the time group, and '26' might be the seat sequence number 26. Don't trust abbreviations lightly when making reservations; always check the full schedule. Missing a session means waiting for a review, which is troublesome. Familiarize yourself with the interface in advance to avoid misreading.

Was this review help?
6
5
Share
Expand All
More Forum Discussions

What is the horsepower of the Geely Boyue?

Geely Boyue has a maximum horsepower of 163ps. Taking the 2021 Geely Boyue as an example, it is a 5-door, 5-seater compact SUV with body dimensions of: length 4519mm, width 1831mm, height 1694mm, wheelbase 2670mm, fuel tank capacity 58l, and curb weight 1575kg. The 2021 Geely Boyue is equipped with a 1.8t turbocharged engine, with a maximum power of 120kw, maximum power speed of 5500rpm, maximum torque speed ranging from 1500rpm to 4500rpm, and is paired with a 6-speed manual transmission.
3
3
Share

How is a car battery charged?

Car battery charging method is: 1. Open the front cover of the car and take out the battery charger; 2. Connect the positive terminal of the battery to the positive terminal of the power source, and the negative terminal of the battery to the negative terminal of the power source. Methods to check for insufficient car battery power are: 1. The car horn sound becomes weaker; 2. The car struggles to start, indicating battery discharge; 3. The battery fault light turns on. Precautions for car battery charging are: 1. Battery voltage below 10% of the rated voltage will cause battery discharge; 2. Avoid water entering the battery during charging; 3. Connect directly to the battery for charging, avoid removing the battery to prevent data loss.
16
0
Share

What Causes the Rattling Noise When the Atenza Goes Over Bumps?

Atenza's rattling noise when going over bumps is caused by loose component screws. It is necessary to visit a 4S shop to check the loose parts and tighten the screws. Below is a related introduction to the Atenza: 1. Body Dimensions: The Atenza has a body length, width, and height of 4870mm, 1840mm, and 1445mm respectively, with a wheelbase of 2830mm. 2. Powertrain: This car uses two engines, one is a 2.0-liter naturally aspirated engine, and the other is a 2.5-liter naturally aspirated engine; paired with a 6AT transmission. (1) 2.0-liter naturally aspirated engine: The engine has a maximum power of 158 horsepower and a maximum torque of 202 Nm. The engine's maximum power speed is 6400 rpm, and the maximum torque speed is 4000 rpm. This engine is equipped with a variable valve timing control system and direct fuel injection technology, and uses an aluminum alloy cylinder head and block. (2) 2.5-liter naturally aspirated engine: The engine has a maximum power of 192 horsepower and a maximum torque of 252 Nm. The engine's maximum power speed is 6100 rpm, and the maximum torque speed is 3250 rpm. This engine is equipped with a variable valve timing control system and direct fuel injection technology, and uses an aluminum alloy cylinder head and block.
8
0
Share

When should the original timing belt be replaced?

The original timing belt should be replaced when the vehicle reaches 80,000 kilometers. The functions of the timing belt are: 1. To drive the engine's valve train, ensuring the intake and exhaust valves open and close at the correct times; 2. To guarantee the engine cylinders can properly intake and exhaust air. The replacement procedure for the timing belt is: 1. Remove the valve cover and the timing belt housing; 2. Rotate the crankshaft to position the first cylinder at top dead center, then secure the crankshaft with the fixing bolt; 3. Rotate the intake and exhaust camshafts—there are grooves at the rear of the camshafts—align the grooves of both camshafts horizontally; 4. Remove the old belt and install the new one; 5. Ensure there is no gap at the crankshaft position sensor during installation to avoid triggering fault codes.
20
1
Share

How to Install a Belt?

The method for installing a belt is as follows: 1. Align the ignition marks of the crankshaft and camshaft; 2. Place the belt on the crankshaft pulley and smoothly guide it upwards from the side opposite the tensioner pulley to place it on the camshaft pulley; 3. Then fold the belt into the side of the tensioner pulley and tighten the tensioner. The belt is an important component of the engine's valve timing system, ensuring accurate intake and exhaust timing by connecting to the crankshaft and matching a specific transmission ratio. Steps for replacing the belt: 1. Lift the car with a jack; 2. Remove the engine undercover; 3. After removing the undercover, the generator belt will be visible; 4. Remove the exposed old generator belt; 5. Install the new engine belt. Situations requiring belt replacement: 1. Abnormal belt wear; 2. Belt folding failure; 3. Belt impact load.
14
0
Share

How to Disassemble the Wuling Hongguang Key?

The method to disassemble the Wuling Hongguang key is: 1. Use a flathead screwdriver to pry open the side opening of the key; 2. Open the key casing along the pried gap. Taking the 2019 Wuling Hongguang S3 as an example, it belongs to the mid-size SUV category, with body dimensions of: length 4655mm, width 1735mm, height 1790mm, a wheelbase of 2800mm, a fuel tank capacity of 49 liters, and a curb weight of 1380kg. The 2019 Wuling Hongguang S3 is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 99PS, a maximum power of 73kW, a maximum torque of 140Nm, and is paired with a 6-speed manual transmission.
11
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.