What does EPS mean when it appears in a car?

1 Answers
ZacharyLee
07/29/25 7:40pm
EPS in a car stands for Electric Power Steering. Its function is to use the power generated by an electric motor to assist the driver in steering. The system directly provides steering assistance through an electric power motor, eliminating the need for components such as a power steering oil pump, hoses, hydraulic fluid, drive belt, and pulley mounted on the engine, saving energy and protecting the environment. The EPS system has many advantages: 1. The motor only provides assistance when steering, which can significantly reduce fuel consumption. 2. The amount of steering assistance can be adjusted via software, balancing ease of steering at low speeds with handling stability at high speeds, and it has good returnability. 3. The steering mechanism operates with less noise and makes turning the wheel easier.
Was this review help?
16
2
Share
More Forum Discussions

What to Do If Your Car Gets Flooded?

If water enters the exhaust pipe after driving through water, immediately call for roadside assistance and wait for rescue. If the water in the exhaust pipe is not severe, you can inspect the electronic systems yourself and remove any accumulated water under the car body. If the car has been severely flooded, you will need a roadside assistance vehicle to tow it to an auto repair shop for servicing.
15
5
Share

How to Solve Insufficient Power in Surui?

Regularly perform maintenance according to the official maintenance manual, including changing the engine oil and oil filter, cleaning or replacing the air filter, and replacing the oil filter. Check whether the throttle valve has carbon deposits, whether the intake manifold is leaking, and whether related sensors are malfunctioning. Regularly inspect the levels of engine oil and coolant. Do not mix different types of engine oil or use water as a substitute for coolant.
7
5
Share

What to Do When Car Glass Near Construction Site Can't Be Cleaned?

Use a dry cloth to wipe it, then clean it directly with glass cleaner, and finally wipe it clean with a warm, damp cloth. You can apply some toothpaste to the spots and then wipe them. Wipe the car glass with a damp cloth first, then use a clean damp cloth dipped in a little alcohol to scrub the car glass vigorously. Use sandpaper specifically designed for car cleaning, and then restore the gloss of the car surface by waxing.
9
1
Share

What are the three methods for plastic parts refurbishment?

For harder plastic parts, find a hard plastic piece of the same type, melt it with a soldering iron, and drip it into the crack until the crack is filled, then smooth it with a hot soldering iron. For thicker soft plastic products that are broken or unglued, use a heated iron rod to make the area to be repaired sticky, align it, and then press it firmly. For thinner and softer plastic products like raincoats, first align the crack, place a piece of glass paper on top, and then press the soldering iron over the cracked area a few times.
10
0
Share

How to steer when the right rearview mirror is narrower at the top and wider at the bottom?

Observe the lower edge of the left rearview mirror, and stop when it aligns with the frontmost horizontal yellow line, then shift into reverse gear; Look at the lower right corner of the left rearview mirror leg, and when the inner corner aligns with the yellow line, turn the steering wheel fully to the right; Turn your head to observe the right rearview mirror, maintaining the vertical distance between the right rear wheel of the car body and the corner of the parking space. If you've turned too much, slightly adjust back.
18
4
Share

How to Open the Interior Handle of XPeng Car?

Gently pry out the door handle trim cover and then unscrew the internal screw, at which point the door handle lock block can be removed. Then, gently pull the door handle with your left hand to create a suitable distance between the door handle and the door. Carefully apply lubricant to the inside of the door handle with your right hand. After applying the lubricant, gently pull the door handle several times to ensure it is fully lubricated. Finally, reinstall it back into place.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.