What does car cornering light mean?

1 Answers
DelaneyLee
07/30/25 1:36am
Car cornering lights refer to the feature where the vehicle's headlights (or fog lights) can rotate a certain angle in the direction of the turn to expand the field of vision. Standard headlights have blind spots during turns, making pedestrians in these areas difficult to notice and potentially leading to hazards. This equipment primarily enhances nighttime driving safety. There are two common types of cornering auxiliary lighting: one is fog light-assisted steering, where the fog light on the same side illuminates when the headlights are on and the vehicle is turning, and automatically turns off when the turn is completed. The other is dynamic headlights, which adjust their angle based on the vehicle's turning direction to ensure safety in blind spots during curves.
Was this review help?
10
1
Share
More Forum Discussions

Which has more space, the Borgward BX7 or the Captiva?

The Borgward BX7 offers more space than the Captiva. Below are the relevant details: 1. Borgward BX7: With a wheelbase of 2760mm, it is the first SUV model launched after Borgward's revival. Its 1911mm wide body leads its class, equipped with a panoramic sunroof that broadens the view, creating more spatial possibilities to meet diverse journey needs. 2. Captiva: It has a wheelbase of 2707mm. This vehicle is a mid-size SUV under Chevrolet, with dimensions of 4690mm in length, 1849mm in width, and 1753mm in height. In terms of suspension, the Captiva uses a MacPherson strut independent suspension at the front and a four-link independent suspension at the rear.
2
1
Share

What are the basic knowledge of car operation?

Car operation basic knowledge is as follows: 1. Steering: (1) The three main components controlled by hands: steering wheel, turn signal, and gear shift. (2) The turn signal is located in the middle-left position of the steering wheel. First turn on the turn signal, then turn the steering wheel. The direction in which the steering wheel is about to turn is the same direction in which the turn signal should be activated. 2. Foot-controlled components: clutch, brake, and accelerator: (1) The left foot controls the clutch; the right foot controls the brake and accelerator. (2) Braking should be gradual, using inertia braking. (3) The key action is not to press the brake all the way down, but to control the extent of braking based on the road conditions ahead (practice is needed to master the technique). (4) The accelerator is used for speeding up, and its use should also be gradual, not pressing it all the way down. When the accelerator is pressed, the speed will increase, and then subsequent gear shifting operations are required.
15
3
Share

What are the reasons for the automatic transmission failure in the Peugeot 307?

The reasons for the Peugeot 307 displaying transmission failure are as follows: 1. Reason one: The transmission temperature is too high. 2. Reason two: The transmission has been used for too long without replacement, leading to oil deterioration. 3. Reason three: Water ingress into the transmission. 4. Reason four: Significant deviation in oil level height. 5. Reason five: Slipping of the friction plates. Relevant information about the Peugeot 307 is as follows: 1. Introduction one: The Peugeot 307 is a compact car with a length, width, and height of 4212 mm, 1762 mm, and 1531 mm respectively, and a wheelbase of 2608 mm. 2. Introduction two: In terms of appearance, the front face design of the Peugeot 307 inherits the new aesthetic elements pioneered by the Peugeot 407, with very distinctive personality characteristics. Combined with the large-mouth-like grille, its visual impact is very striking.
8
3
Share

Why does the Nissan Sylphy make a squeaking noise when the air conditioning is turned on?

Nissan Sylphy makes a squeaking noise when the air conditioning is turned on because the air conditioning pulley and the belt slip, and during the slipping process, a sharp friction sound is produced. Check if there is oil contamination on the belt. Specific details are as follows: 1. Oil contamination: If the belt slips due to oil contamination, clean it thoroughly. If not, adjust the compressor's position bolts to tighten the compressor belt, which can increase friction. 2. Belt looseness: If the belt is loose and causes abnormal noise, you can press the belt's tension by hand. If it's too loose, tighten it. If the belt has been used for too long, it needs to be replaced. 3. Tensioner damage: If the belt's tensioner is damaged, it can also cause abnormal noise, and a new tensioner needs to be replaced.
6
2
Share

What are the reasons for a sudden failure to start a Bora car?

There are several reasons why a Bora car suddenly fails to start: 1. Symptom characteristics: The starter begins to turn but the rotation speed is insufficient, meaning it lacks power, and later the starter only makes a clicking sound without turning. Low temperatures in winter and forgetting to turn off certain electrical equipment can cause the vehicle to fail to start, especially when used for long periods of short-distance, low-speed driving in winter, which can result in the battery voltage dropping below the rated value, making it impossible to start or operate normally. Emergency solution: If this occurs, please call the service station for assistance, or find another car to jump-start, or temporarily start the engine, after which you must go to the service station to recharge the battery. 2. Symptom characteristics: There is no oil pressure in the engine fuel supply line. This situation often occurs on particularly cold mornings and is caused by long-term dirt accumulation in the fuel line. When the temperature is extremely low, water and debris mix, blocking the fuel line and preventing the engine from starting. Emergency solution: Place the car in a warm environment, and it will start after a while; or use a fuel line cleaning method to completely resolve the issue.
14
5
Share

Why can the car door still be opened when the central lock is engaged?

It is normal for the car door to still be opened when the central lock is engaged. The basic structure of the door lock is as follows: 1. Door lock switch: Most central door lock switches consist of a master switch and sub-switches. The master switch is installed on the door next to the driver and can lock or unlock all doors of the vehicle; sub-switches are installed on other doors and can individually control a single door. 2. Door lock actuator: The door lock actuator is controlled by the door lock controller and performs the tasks of locking and unlocking the door. There are mainly three types of structures: electromagnetic, DC motor, and permanent magnet motor. 3. Door lock controller: A control device that provides lock/unlock pulse current to the door lock actuator. It has the function of controlling the current direction of the actuator and, to reduce working time, includes a timing function. According to its control principle, it can be roughly divided into three types: transistor type, capacitor type, and speed sensing type.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.