What does 6AT transmission mean?

Impact of Replacing Car Doors on the Vehicle

The impact of replacing car doors on the vehicle is as follows: 1. Paint color mismatch. If the door is replaced at an external repair shop, the repainted door may exhibit color differences compared to the original factory door. If door replacement is necessary, it is best to have it done at a 4S shop. 2. Reduced sound insulation. Replacing doors through unofficial channels can easily lead to issues in assembly processes or details, resulting in air leaks or increased noise during high-speed driving, which degrades the vehicle's sound insulation and affects cabin comfort. Precautions after replacing car doors are as follows: 1. Observe whether the gap width of the car door is uniform and the surface is smooth; otherwise, abnormal noises may occur. 2. Check the door's sealing integrity to avoid issues like water or air leaks. 3. Repeatedly open and close the door to test for smooth operation or abnormal noises.

7

4

Share

What are the Five Oils, Four Filters, and Three Fluids in a Car?

In a car, the Five Oils, Four Filters, and Three Fluids refer to: Five Oils include gasoline, engine oil, transmission fluid, brake fluid, and power steering fluid; Four Filters are the engine oil filter, air filter, cabin air filter, and fuel filter; Three Fluids consist of windshield washer fluid, coolant, and battery fluid. Below are details about the Five Oils: 1. Engine Oil. Some cars can directly monitor oil levels via the onboard computer. For manual checks, turn off the engine, open the engine oil cap, wipe the dipstick clean, insert it into the oil tank, and then pull it out. If the dipstick shows the oil level below the minimum (Min), promptly add engine oil of the same specification. 2. Brake Fluid. Open the engine compartment cover to find a semi-transparent brake fluid reservoir. If the fluid level is below the minimum mark, add brake fluid of the same specification. The recommended replacement interval is 1 year or 20,000 kilometers. 3. Gasoline. The dashboard will flash a warning when the fuel level is below the tank's minimum. 4. Transmission Fluid. Start the engine, engage the handbrake, wait briefly for the engine to reach operating temperature, then press the brake pedal and shift through P, R, N, and D gears before returning to P. Open the transmission fluid cap and check the level with the dipstick. Some transmissions don’t require fluid changes, so don’t be surprised if there’s no dipstick. 5. Power Steering Fluid. Start the engine and open the power steering fluid cap to check the level with the dipstick. For cars with electronic power steering, this check is unnecessary.

14

5

Share

What is the difference between a radial master cylinder and a conventional master cylinder for motorcycles?

The difference between a radial master cylinder and a conventional master cylinder for motorcycles lies in the distinct linear relationship between lever travel and piston movement, as well as their appearance: Difference in linear relationship between lever travel and piston movement: In a radial master cylinder, the movement direction of the hydraulic piston aligns with the action direction of the brake lever, resulting in a linear relationship between lever travel and piston stroke. In contrast, conventional master cylinders (commonly equipped on small-to-medium displacement motorcycles) feature hydraulic pistons that move perpendicular to the brake lever's action direction. This angular displacement creates a nonlinear relationship between lever travel and piston stroke. Difference in appearance: The radial master cylinder incorporates a separate brake fluid reservoir. This design isn't merely aesthetic but serves to increase reservoir depth, preventing air ingress into brake lines during extreme leaning angles. Air in brake lines can cause brake fade (softening) and reduced responsiveness, compromising both braking performance and riding safety.

3

2

Share

When will the China VI emission standards be implemented?

Currently, the country has divided the "China VI Standard" into two phases: "China VIa" and "China VIb", which will be uniformly implemented nationwide in 2020 and 2023 respectively. Here is an introduction to the China VI Standard: 1. The China VI Standard, also known as the "National Sixth Stage Emission Standards for Motor Vehicles", is established to implement environmental protection laws, reduce and prevent pollution from vehicle exhaust, protect the ecological environment, and ensure human health. 2. The China VI Standard was issued by the Ministry of Environmental Protection and the General Administration of Quality Supervision, Inspection and Quarantine on December 23, 2016, and June 22, 2018, respectively. The "Limits and Measurement Methods for Emissions from Heavy-Duty Diesel Vehicles (China VI)" came into effect on July 1, 2019. The implementation of the China VI Standard will impose stricter requirements on emissions such as carbon monoxide, nitrogen oxides, and hydrocarbons. 3. Based on past experience, when the China V Standard was implemented, vehicles meeting the China II Standard were phased out. Therefore, it is highly likely that vehicles meeting the China III Standard will also be phased out after the implementation of the China VI Standard. The timing of the phase-out will depend on national policies and the actual conditions of each region.

6

0

Share

Can the gap between the bumper and fender be adjusted?

The gap between the bumper and fender cannot be adjusted. Introduction to car bumpers: The vehicle's bumper is a safety device located at the front and rear of the vehicle. Early bumpers were made of steel plates, while later versions use engineering plastics, making them one of the vehicle's safety devices. The production of vehicle bumpers must comply with the automotive protective bumper industry standards and requires inspection before being put into production and use. Function of car bumpers: The front and rear bumpers of a vehicle are vulnerable accessories that serve decorative purposes, effectively absorbing external impacts while protecting the entire vehicle and its occupants. Replacing the bumper will not have any impact on the vehicle.

12

4

Share

Does Watching Drive-In Movies Harm the Car?

Watching drive-in movies may affect driving safety. Vehicle inspection before departure: Before setting off each day, conduct a comprehensive inspection of the vehicle, including checking for oil or water leaks, measuring tire pressure to ensure it is appropriate, inspecting the engine oil condition to verify its color is normal and the oil level is correct. Safe driving: Use seat belts correctly; in the event of a severe collision, the protection provided by seat belts is no less than that of airbags. Avoid fatigued driving and take a break every 2 hours. Follow traffic rules: Especially on highways, do not speed. Speeding not only risks penalties from traffic police but, more importantly, is unsafe.

9

1

Share

What does 6AT transmission mean?

Impact of Replacing Car Doors on the Vehicle

What are the Five Oils, Four Filters, and Three Fluids in a Car?

What is the difference between a radial master cylinder and a conventional master cylinder for motorcycles?

When will the China VI emission standards be implemented?

Can the gap between the bumper and fender be adjusted?

Does Watching Drive-In Movies Harm the Car?

How to Check if a Vehicle Has ETC?

Should Brake Pads Be Replaced on All Four Wheels Together?

Solutions for Unstable Idle Speed

What does the TC light on a car mean?