What does 5w30 oil mean?

1 Answers
Leonardo
07/29/25 7:22pm
Here is a detailed introduction to the meaning of 5w30 oil: 1. W stands for winter. The number before W is 5. The smaller the number, the better the fluidity of the oil at low temperatures, and the lower the applicable minimum temperature. 5W means it can be used at temperatures above -30°C. 2. The number after W is 30, which refers to the viscosity of the oil at 100°C. The larger the number, the higher the viscosity of the oil, the stronger the resistance to high temperatures, and the better the high-temperature protection performance. More information about 5w30 oil is as follows: 1. From the perspective of vehicle brands, 5W30 is more suitable for Japanese and Korean cars, as the engines of these two series of vehicles are more precise and have smaller gaps. If we only look at the viscosity grade, 5W30 is more suitable for colder regions and winter. 2. In addition to learning how to read the viscosity grade of oil, you should also have a general understanding of the shelf life of oil; 3. For fully synthetic oil, it should be replaced approximately every 10,000 kilometers or once a year; 4. For semi-synthetic oil, it should be replaced every 7,500 kilometers or every seven to eight months; 5. For mineral oil, the performance is not as good, so the replacement cycle should be shortened accordingly. It should be replaced every 5,000 kilometers or six months.
Was this review help?
11
4
Share
More Forum Discussions

What are the consequences of not wearing a seat belt?

The following are the consequences of not wearing a seat belt: 1. Consequences for pregnant women and passengers holding infants: For pregnant women or passengers holding infants who genuinely cannot wear seat belts, traffic police will enforce the law humanely during roadside checks, issuing warnings before letting them pass. 2. Consequences for rear-seat passengers not wearing seat belts: Drivers will also be penalized if rear-seat passengers do not wear seat belts, which many drivers find unfair. 3. Inability to protect passengers in the event of a traffic accident: If seat belts are properly fastened during a traffic accident, the injuries sustained by vehicle occupants will be significantly less severe compared to not wearing seat belts.
13
1
Share

Can You Not Remove the Carpet When a Car Gets Flooded?

You need to remove the carpet when a car gets flooded. After flooding, the car carpet absorbs a large amount of water. If not removed promptly, the accumulated water will cause a foul odor that lingers and fails to evaporate, significantly impacting the driving and riding experience. The interior and carpets of a flooded vehicle absorb substantial moisture—squeezing the inner sponge will release a lot of water. Since the interior is mostly made of fabric or leather, prolonged soaking in water leads to mold growth and unpleasant odors. Hence, the distinct smell of a flooded car is easily recognizable. Therefore, it's essential to remove these soaked carpets as soon as possible, clean them thoroughly, and dry them under direct sunlight to eliminate moisture.
12
0
Share

What Causes Audi Parking Brake Malfunction?

Audi parking brake malfunction is most commonly caused by the handbrake lever not being fully released. Below are the relevant details: 1. Introduction: The parking brake, usually referring to the manually operated brake installed in motor vehicles, commonly known as the handbrake, is used to stabilize the vehicle after it has come to a stop, preventing accidents caused by rolling on inclined surfaces. The typical handbrake is positioned within easy reach of the driver's right hand for convenient operation. 2. Common Issues: For Audi parking brake malfunctions, first check if the handbrake lever is fully released. If not, the handbrake switch underneath may remain engaged, or the handbrake might not have been pressed to the switch position. Next, check if there is a shortage of brake fluid, and if so, replenish it promptly. Finally, it may be necessary to visit a 4S dealership for a diagnostic scan with a computer tester. After repairing according to the fault code, reset the malfunction indicator light.
14
3
Share

What causes an Audi A6 to struggle when climbing uphill?

There are several reasons that can cause insufficient power, such as a clogged three-way catalytic converter, insufficient fuel pressure, or turbocharger failure. Below are detailed explanations: 1. Three-way catalytic converter: As the most critical component in a gasoline vehicle's exhaust purification system, the three-way catalytic converter is responsible for the catalytic reduction of harmful gases in the exhaust, including carbon monoxide (CO), hydrocarbons (HC), and nitrogen oxides (NOx). It converts these three main harmful gases into non-toxic and harmless substances like water (H₂O), carbon dioxide (CO2), nitrogen (N2), and oxygen (O2), which are then expelled. 2. Turbocharger failure: Blockages in the intake system, such as a clogged air filter or accumulated dust in the intake pipes, increase the turbocharger's suction resistance. When the air flow drops below a certain level, it leads to a decrease and fluctuation in the engine's boost pressure, causing severe turbocharger vibration. This results in a "rumbling" noise in the engine's intake pipe, reduced engine power, unbalanced operation, and black smoke from the exhaust pipe. If surging occurs, the engine should be stopped immediately to inspect and clean the relevant components; otherwise, the turbocharger may be damaged due to increased vibration.
6
1
Share

Can I Change Driving Schools After Passing Subject 1?

You can change driving schools, but since a driver training contract relationship has already been established between the student and the driving school, it is necessary to negotiate with the original driving school. If the driving school agrees to the student's transfer and refunds part of the fees (the amount of which is also subject to negotiation between both parties), then you can apply to the vehicle management office to cancel the previous registration information and re-register. Below are the details about changing driving schools: 1. As for the refund amount when changing driving schools, there is no reference data available. The fees vary by region and driving school, and each individual's situation is different. The final refund amount depends on the negotiation between both parties. 2. If the driving school has relocated, causing the student to travel an excessive distance for training, this is considered the driving school's unilateral reason. If both parties cannot reach an agreement on this situation, the student may request a full or partial refund of the tuition fees. If the student wants to change driving schools due to personal reasons, the driving school is not obligated to refund the fees. Ultimately, it depends on the negotiation outcome between both parties.
4
5
Share

What is the difference between 280 and 330?

Here are the differences between 280 and 330: 1. Torque rating: The torque rating of 280 is 280 N·m. The torque rating of 330 is 330 N·m. 2. Engine power: The 280 has a smaller engine power. The 330 has a more powerful engine. 3. Vehicle grade: The 280 has a lower vehicle grade. The 330 has a higher vehicle grade. Here is some additional information: 1. Due to different torque tuning for different models, Volkswagen divides the torque value of car engines into several "torque grades" with an interval difference of 50 N·m to distinguish the grades more clearly. 2. Each "torque grade" uses a "marker value," which is obtained by rounding the average torque value of that grade.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.