What does 10w40 mean for car engine oil?

What Causes the Brake Pedal to Be Too Hard to Press Down?

The reason why the brake pedal is too hard to press down is due to air leakage or failure of the car's vacuum booster pump. Below is relevant information about brakes: 1. Precautions: To prevent "jerky" braking, if the braking distance is sufficient, you can slowly and steadily press the brake pedal to decelerate. When the car is about to stop, you can gently release the brake pedal until the car comes to a complete stop. 2. Braking on slopes: Braking on uphill sections is similar to braking on flat roads—both require gently pressing the brake pedal. However, the release should be quicker than on flat roads. On downhill sections, avoid prolonged braking as it can easily overuse the brake friction pads, reducing their effectiveness. Instead, use intermittent braking (pump braking) to decelerate and bring the car to a stop.

19

4

Share

Is It Normal for a 125cc Motorcycle to Run at 80 km/h?

It is relatively normal for a 125cc motorcycle to run at 80 km/h on open roads, but in urban areas, maintaining a speed of 60 km/h is safer. Here are the relevant details: 1. Detail One: Typically, the maximum designed speed for a 125cc motorcycle is around 95 km/h. 2. Detail Two: If the motorcycle in use has not had its fuel system inspected and cleaned for a long time, its speed performance may be affected to some extent. Therefore, both the carburetor and electronic fuel injection system require regular maintenance, and the condition of the air filter should also be checked periodically.

1

Share

What is the MIIT fuel consumption of the Haval F7?

Haval F7 is mainly divided into four models, the details are as follows: 1. The 1.5T engine with a 7-speed dual-clutch transmission has a fuel consumption range of 8-11. 2. The 1.5T engine with a 7-speed wet dual-clutch transmission has a fuel consumption range of 8-10.5. 3. The 2.0T engine with a 7-speed dual-clutch transmission has a fuel consumption range of 9-12. 4. The 2.0T engine with a 7-speed wet dual-clutch transmission has a fuel consumption range of 9-12.5. Additional details about the Haval F7 powertrain: 1. Equipped with 1.5GDIT and 7DCT: 1.5GDIT: "China's Top 10 Engines", supported by 8 advanced technologies; 2.0GDIT: 6 advanced technologies. 7DCT: The first domestically developed transmission, with 85 patents/independent intellectual property rights, "World's Top 10 Transmissions". 2. Golden powertrain combination, new chassis tuning + all-terrain technology: BorgWarner all-wheel drive system, four-wheel drive control, front-wheel drive cruising, rear-wheel drive acceleration, single-wheel drive escape. 3. Six all-terrain driving modes: Standard, Sport, Economy, Mud, Sand, and Snow modes.

12

0

Share

What Causes a Manual Transmission Car to Fail to Shift Gears After Starting?

Common reasons why a manual transmission car fails to shift gears after starting are analyzed as follows: 1. Clutch disc not disengaging properly: If there is an issue with the clutch disc disengagement, it is necessary to visit a repair facility to inspect and adjust the clutch or replace it. 2. Damaged clutch disc and pressure plate: This causes the clutch to malfunction, preventing the disconnection and engagement of engine power. The issue can be resolved by inspecting and replacing the clutch disc and plate. 3. Worn shift mechanism: Internal gear wear in the shift lever causes it to get stuck, making gear shifting impossible. It is essential to promptly visit a repair facility to diagnose the fault and replace the necessary parts.

6

4

Share

How Much Fuel Should Remain in the Tank When Replacing the Fuel Pump?

4S shops recommend keeping about 1/3 of fuel remaining. Below is a partial introduction about the fuel pump: 1. Function: The main function of the fuel pump is to supply fuel to the engine. The fuel pump delivers high-pressure fuel to the injection pipe, ensuring a continuous supply of fuel to the injectors. 2. Composition: The fuel pump consists of an electric motor, a pressure limiter, and a check valve. The electric motor actually operates within the fuel inside the pump housing. There's no need to worry, as there are no ignition sources inside the housing. The fuel lubricates and cools the fuel motor. A check valve is installed at the fuel outlet, and the pressure limiter is located on the pressure side of the pump housing, featuring a passage leading to the fuel inlet.

14

2

Share

What is the method for changing transmission fluid using a circulation machine?

The method for changing transmission fluid using a circulation machine is: 1. Remove the protective plate and loosen the drain plug; 2. Drain the used fluid through the drain plug hole and by removing the oil pan; 3. Expose the automatic transmission and remove the oil pan; 4. Clean the oil pan with a cleaning agent; 5. Reinstall the oil pan and add transmission fluid; 6. Unscrew the drain and fill plug holes of the automatic transmission, and insert both the fill and drain hoses of the circulation machine into the transmission; 7. Start the circulation machine; 8. Start the vehicle and shift through all gears; 9. When the color in the oil sight glass turns clear red, the circulation machine fluid change is complete.

5

1

Share

What does 10w40 mean for car engine oil?

What Causes the Brake Pedal to Be Too Hard to Press Down?

Is It Normal for a 125cc Motorcycle to Run at 80 km/h?

What is the MIIT fuel consumption of the Haval F7?

What Causes a Manual Transmission Car to Fail to Shift Gears After Starting?

How Much Fuel Should Remain in the Tank When Replacing the Fuel Pump?

What is the method for changing transmission fluid using a circulation machine?

Is driving with a license expired for three days considered unlicensed driving?

What to Do If the Driver's License Expires?

What is the coverage of BMW extended warranty service?

Is it necessary to replace the filter when changing AT transmission fluid?