What does 1/minx1000 mean?

1 Answers
ZoeLee
07/29/25 4:38pm
1/minx1000 means 1000 revolutions per minute. The following is an introduction about engine speed: Impact of transmission on speed: The number of gears and the transmission ratio of the gearbox affect the engine speed variation and power output. The more gears the transmission has, the greater the possibility for the engine to operate at maximum power. However, more gears make the transmission structure more complex, leading to significant difficulties in maintenance and disassembly. Therefore, 5-6 forward gears are generally used. If the transmission ratio is properly allocated, the engine can frequently operate within the range of maximum power, increasing the vehicle's reserve power and improving throttle acceleration and climbing ability. Improper allocation of the transmission ratio coefficient can lead to difficulties in gear shifting and affect the engine's power output. Impact of fuel on speed: The quality of engine combustion has a significant impact on power output, affecting the engine speed. When the speed of a gasoline engine increases, the flow rate of the mixture through the intake valve accelerates, and the speed of the piston moving upward during the compression stroke also increases. As a result, the vortex and turbulence in the cylinder intensify, accelerating the exchange between unburned and burned gases, which greatly improves the flame propagation speed. To ensure normal combustion, the ignition timing needs to be appropriately advanced as the speed increases. When the load decreases and the throttle opening decreases, the engine speed drops. At this time, the fresh charge entering the cylinder decreases, and the residual gas coefficient increases, lengthening the flame front gas. Consequently, the combustion speed decreases, the maximum combustion temperature and pressure drop, the combustion quality deteriorates, and post-combustion increases, leading to greater heat loss.
Was this review help?
5
3
Share
More Forum Discussions

How Many Times Should You Press the One-Button Start to Turn Off the Engine?

When in P gear, press once to directly turn off the engine and cut power; when in N gear, press once to turn off the engine but not cut power—you need to shift to P gear and press twice to cut power. Important Note: If an emergency occurs while the vehicle is in motion, you can turn off the engine by pressing the one-button start for more than 3 seconds or pressing it three times consecutively. In this case, the power switches to ACC mode. The correct steps to turn off the engine using the one-button start are as follows: Press the brake, bring the vehicle to a complete stop, and shift from D gear to N gear. Engage the handbrake (if it's an electronic handbrake, simply pull it up). Release the foot brake but do not turn off the power—this is to confirm that the vehicle comes to a complete stop under the handbrake's effect and to prevent the P gear from locking. Continue pressing the foot brake, shift from N gear to P gear, release the foot brake, press the one-button start, and the power will turn off, completing the engine shutdown.
7
0
Share

How many seconds count as stopping in Subject 2?

In Subject 2, a pause of 2 seconds is considered an intermediate stop. During the Subject 2 test, most items require continuous operation without stopping, otherwise the test will be judged as a failure. Principle: The test vehicle's wheels are equipped with sensors; an intermediate stop, meaning the speed is 0, will be detected if the pause exceeds 2 seconds during the test, and the sensor will feedback to the computer, resulting in a failed test. Solution: Generally, the instructor will take the examinee to familiarize themselves with the test site in advance. The size of the test site is similar to the practice field, so getting familiar with the road conditions and finding the right points in advance is sufficient. Additionally, during the Subject 2 test, although the speed should be slow, it should not be too slow; maintaining the usual practice speed is recommended.
2
0
Share

What are the reasons for no response when pressing the one-touch start button?

Issues with the car key, gear not in P position, and not pressing the brake can cause the one-touch start to not respond. Car key issues: For example, the key battery is dead, or the key's radio waves are being interfered with, etc. Frequently placing the car key near electronic devices such as mobile phones, computers, or TVs can easily cause interference with the low-intensity radio waves in the key, making it difficult for the car's sensor to detect it. In such cases, the one-touch start will not respond. Gear not in P position: Currently, most car models cannot start if the gear is not in the P position. This is a safety feature designed by manufacturers to prevent the car from starting when the gear is in D or R position. Not pressing the brake: Many cars require the brake to be pressed for the one-touch start to activate the engine. If the brake is not pressed, only the car's electrical circuits are connected, which is also a safety consideration in the design. Solutions for no response when pressing the one-touch start button: For car key issues, replace the key battery or move away from the interference area. If the gear is not in P position, shift it to P and restart. If the brake is not pressed, press the brake to start.
17
1
Share

What does the car OBD port mean?

The car OBD port refers to the on-board diagnostic system. By connecting to the OBD port, you can view real-time car data, detect car faults, and facilitate car repairs, development of car-related functions, and modification of car equipment. The car OBD port is an interface on the car similar to a power socket. Simply put, its function is to allow technicians to connect a computer to the OBD port and access vehicle information and status. For example, if the vehicle has a fault code, the maintenance personnel only need to connect a computer to the OBD interface to determine where the problem lies and proceed with repairs.
13
2
Share

What color is automotive primer generally?

Automotive primer is generally black, white, or gray, with gray being the most commonly used on vehicles. If the primer becomes exposed, it needs to be repaired. When primer is exposed, the extent of the damage should be assessed. If the primer hasn't been scraped off, only the topcoat needs to be repaired. If the primer is damaged, maintenance is required. If not addressed promptly, the car's surface may rust. Solvent-based automotive primers primarily use nitrocellulose resin, epoxy resin, alkyd resin, amino resin, or phenolic resin as the base material. Pigments such as iron oxide red, titanium white, carbon black, and other fillers are used. The application methods include spraying and dip coating.
1
2
Share

What Causes the Buzzing Sound When Turning on the AC Button?

Possible reasons for the buzzing sound when turning on the AC button include belt slippage, air conditioning compressor failure, or foreign objects in the air duct. The corresponding solutions are as follows: Belt Slippage: The air conditioning compressor is driven by the engine crankshaft via a belt. If the belt becomes loose, aged, severely worn, or if the tensioner pulley lacks sufficient tension, it can cause the belt to slip, resulting in abnormal noise. If the issue is due to the belt, simply replace it. If the problem lies with the tensioner pulley, the pulley needs to be replaced. Air Conditioning Compressor Failure: When the AC switch is turned on, the air conditioning compressor starts operating. If the compressor is damaged, it may produce abnormal noise. It is recommended to visit a 4S shop for replacement or repair. Foreign Objects in the Air Duct: When there are foreign objects in the air conditioning system's duct, these objects can rotate repeatedly with the blower's airflow and collide with the air filter, causing abnormal noise. Remove the air filter and carefully inspect and clean any foreign objects in the duct.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.