···
Log in / Register

What documents are required for vehicle inspection in Beijing?

1 Answers
McNevaeh
07/29/25 5:48pm
Here are the procedures required for the inspection and verification of a motor vehicle driver's license: 1. Bring the motor vehicle registration certificate. 2. The ID card or a copy of the ID card of the motor vehicle owner. 3. The valid compulsory traffic insurance policy for the current year of the motor vehicle, which is sufficient to complete the annual inspection procedures for the motor vehicle. The annual inspection procedures can be conducted three months in advance. Below are the precautions for motor vehicle inspection: 1. Any traffic violations of the motor vehicle must be resolved. 2. Any unresolved traffic accidents involving the vehicle must be settled before participating in the annual inspection procedures for the motor vehicle. Otherwise, the motor vehicle will not be allowed to undergo the annual inspection. 3. If a motor vehicle fails to complete the annual inspection procedures for three consecutive inspection cycles, the vehicle management office or the traffic management department of the public security authority will process the motor vehicle as scrapped.
Was this review help?
2
4
Share
More Forum Discussions

What is the installation method for the seat belt of the Chevrolet Cruze?

The installation method for the seat belt of the Chevrolet Cruze is as follows: 1. Locate the wiring under the car seat and find the sensor wire for the safety buckle; 2. Remove the seat cushion, take off the airbag, locate the bolt fixing point for the seat belt, and remove the seat belt buckle; 3. Find the seat cushion sensor inside the seat cushion and remove it; 4. Install the safety buckle onto the seat and insert the bolt; 5. Install the weight sensor on the car seat, attach the retractor, and tighten it with a wrench; 6. Restore the car seat cushion to its original position and arrange the wiring at the bottom of the seat properly. Taking the 2018 Chevrolet Cruze as an example, it belongs to the compact car category, with body dimensions of length 4666mm, width 1807mm, height 1460mm, and a wheelbase of 2700mm.
15
5
Share

What are the causes of inner tire wear on rear wheels?

The causes of inner tire wear on rear wheels are: 1. Insufficient toe-in or camber angle of steering wheels, which indicates inaccurate four-wheel alignment; 2. Failure to perform dynamic balancing after tire repair or replacement; 3. Excessive differences in tire pressure. The functions of tires are: 1. Transmitting driving force, braking force, and steering force to achieve vehicle operation; 2. Supporting vehicle load; 3. Reducing and absorbing vibrations and impacts during driving to prevent severe vibrations from damaging automotive components. Tire maintenance methods include: 1. Regularly removing stones from tire treads; 2. Minimizing prolonged exposure to sunlight; 3. Timely checking tire pressure; 4. Paying attention to suspension maintenance; 5. Periodically inspecting front wheel alignment; 6. Adopting proper driving techniques by choosing appropriate road surfaces, avoiding objects that may puncture or scratch tires, and steering clear of chemical spills that could corrode tires.
1
1
Share

Which country is the Michelin tire brand from?

Michelin tires are a French brand. Tires are circular elastic rubber products mounted on various vehicles or machinery to roll on the ground. They are installed on metal rims to support the vehicle body, absorb external shocks, ensure contact with the road surface, and maintain the vehicle's driving performance. The functions of tires include: 1. Supporting the entire weight of the vehicle and bearing the load; 2. Transmitting traction and braking torque to ensure adhesion between the wheels and the road surface; 3. Reducing and absorbing vibrations and impacts during driving, preventing severe vibrations and premature damage to vehicle components; 4. Adapting to the vehicle's high-speed performance, reducing driving noise, and ensuring safety, handling stability, comfort, and energy efficiency.
2
4
Share

Where is the USB port in the Qoros 5?

The USB port in the Qoros 5 is located inside the center armrest. The USB port can be used to read data from a USB drive for media playback or to charge electronic devices. Taking the 2019 Qoros 5 as an example, its body dimensions are: length 4600mm, width 1869mm, height 1658mm, with a wheelbase of 2710mm and a curb weight of 1580kg. The 2019 Qoros 5 features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.6L turbocharged engine, delivering a maximum horsepower of 197PS, maximum power of 145kW, and maximum torque of 290Nm, paired with a 7-speed dual-clutch transmission.
17
3
Share

Should the car air conditioner AC be turned on in winter?

In winter, there is no need to turn on the AC when using the car's heater. Pressing the AC button activates the compressor, which provides cold air, but this is unnecessary for heating. The heater works by transferring part of the heat originally dissipated by the radiator into the cabin, so using cold air would counteract some of the engine's power, whereas the heater does not affect engine performance. Here is an introduction to the AC function: 1. The AC button activates the compressor, which pressurizes the refrigerant (Freon). To use the heater, simply adjust the fan speed button to blow warm air. The heater utilizes the car's internal heat cycle, transferring heat from the radiator into the cabin without increasing fuel consumption. However, the heater requires preheating; when the car is first started, the coolant temperature is low, so it takes some time before the blower can deliver warm air. 2. The AC is the cooling function, which requires the most work from the air conditioner and consumes the most fuel. On the other hand, the heater does not require "cooling" at all, as the car can fully utilize the heat generated by the engine to operate the air conditioning system.
16
1
Share

What does electronic gear shift in cars mean?

Electronic gear shift in cars refers to the computer assisting in gear shifting, where only a signal needs to be sent. Electronic gear shifts are generally found in automatic transmission models. The method of using an electronic gear shift lever is as follows: 1. When parking, press the P button on top of the gear lever; the P letter will light up, indicating that the parking gear is engaged. 2. Pull the gear lever backward once; the D light will turn on, and after engaging the D gear, the electronic gear lever will automatically rebound. 3. When the transmission is in D gear, pull the gear lever backward once; the M light will turn on, indicating manual mode. 4. When in D or R gear, push the gear lever in the opposite direction of the current gear; the N light will turn on, indicating that the neutral gear is engaged at this moment. 5. Hold down the unlock button on the left side of the gear lever and push the gear lever forward; the R light will turn on, indicating that the reverse gear is engaged.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.