What documents are needed to check traffic violations?

1 Answers
MacLola
07/30/25 3:36am
To check traffic violations, you need to bring the vehicle registration certificate, your driver's license, ID card, and penalty notice (if available, otherwise not required). Then go to the local traffic police brigade or each detachment to print the traffic violation fine notice (penalty decision). Below is more information about traffic violations: 1. Definition: Traffic violations refer to the behavior of motor vehicles violating the Road Traffic Safety Law and traffic management regulations. Traffic violation queries are to check such violations. 2. Penalties: Penalties for traffic violations include warnings, fines (vehicle seizure), temporary suspension of driver's license, revocation of driver's license, cancellation of driver's license, administrative detention, and criminal liability for those who constitute a crime.
Was this review help?
18
0
Share
More Forum Discussions

How to Identify Hydraulic Cylinder Models?

By observing the national standard regulations, hydraulic cylinder models can be identified based on different usage types, cylinder bore, and stroke. Below is a partial introduction to hydraulic cylinders: 1. Function: CJT for 3.5Mpa, CTJ for 7Mpa, CTJ for 14Mpa, CTJ for 21Mpa, DG for vehicle hydraulic cylinders, HSG for engineering hydraulic cylinders, Y-HG1 for metallurgical equipment. 2. Configuration: The cylinder is the most critical component of construction machinery. Traditional processing methods include: broaching the cylinder body – fine boring the cylinder body – grinding the cylinder body. The rolling method involves: broaching the cylinder body – fine boring the cylinder body – rolling the cylinder body. However, in terms of time comparison: grinding 1 meter of cylinder body takes about 1-2 days, while rolling 1 meter of cylinder body takes about 10-30 minutes.
3
0
Share

What Causes Loud Motorcycle Noise?

There are many factors that affect motorcycle noise, which can be summarized into the following categories: temperature, speed, load, and lubrication. Temperature: Some engine noises appear as the temperature rises, while others diminish with increasing temperature. The occurrence of certain noises is often accompanied by heating phenomena. Therefore, in addition to listening to the noise, it is also necessary to measure the temperature to aid in diagnosis. Speed: Noise has a certain relationship with engine speed and vehicle speed. Load: Load has a certain impact on noise. Generally, noise increases with the increase in load, which is a common pattern. Lubrication: Regardless of the type of noise, when lubrication conditions are poor, the noise is usually more severe.
1
3
Share

How to Turn on the Rear Fog Light?

By rotating the control ring to align the rear fog light symbol with the activation point, the dashboard will display the rear fog light indicator, indicating that the rear fog light is turned on. Below is some information about fog lights: 1. Types: Typically, the fog light button is located on the light control lever and is divided into front fog lights and rear fog lights. 2. Front fog lights: To turn on the fog lights, you need to activate the vehicle's lights, i.e., turn on the parking lights. Locate the fog light symbol on the vehicle's light control lever and rotate the control ring. Align the front fog light symbol with the activation point, and the dashboard will display the front fog light indicator, indicating that the front fog light is turned on.
7
5
Share

What Causes the 4LO Light to Flash?

4LO flashing is caused by: 1. Engine misfire leading to excessively high exhaust temperature; 2. Individual cylinders not functioning properly; 3. Overly rich air-fuel mixture causing poor combustion in the engine. Taking the Prado as an example, solutions for 4LO flashing include: 1. Switch between high-range and low-range 4WD, rev the engine a few times during the switching process, and firmly press the ABS sensor connectors near the front and rear wheels as well as the 4WD transfer case connector under the middle of the vehicle; 2. Disconnect the battery for 10 minutes and then reconnect it to see if the issue resolves; 3. Use a diagnostic scanner to read specific fault codes and proceed with repairs. The Prado is an imported ORV with excellent power performance, meeting Euro III emission standards. Its advanced engine delivers strong output power and torque, complemented by a highly rigid frame and reinforced suspension system, making rough journeys comfortable and smooth.
6
5
Share

What Causes Brake Disc Noise in Cars?

The causes of brake disc noise in cars are: 1. Noise caused by brake disc deformation: When the thickness of the brake disc changes in the circumferential direction, the brake disc needs to be repaired and ground; 2. Severe brake disc wear: Severe wear on the brake disc can form deep grooves on the disc, and friction between the brake disc and the edges of the grooves can cause noise. If the grooves are not deep, grinding the edges of the brake pads may suffice. If the grooves are very deep, replacement is necessary; 3. Foreign objects between the brake pads and brake disc: Small stones or water films can cause noise, which usually disappears after driving for a while. Alternatively, the foreign objects can be removed manually; 4. Missing or damaged fixing screws of the brake disc can also cause brake noise; 5. New cars during the break-in period or after replacing brake pads may produce some noise, which is normal and will disappear after the break-in period.
1
4
Share

What lights should be turned on when a car enters a tunnel?

When entering a tunnel, a car should turn on the contour lights and low beam headlights. Below is more information about turning on the lights after entering a tunnel: 1. Contour lights: Because the light outside the tunnel during the day is strong and glaring, while the light inside the tunnel is relatively weak, there is a period of eye adaptation when entering the tunnel. During this process, the driver can easily affect their judgment of road conditions. Turning on the lights can help the driver observe the road conditions and also alert other vehicles. 2. Low beam headlights: When entering a tunnel, low beam headlights should be turned on to provide close-range illumination. This allows the driver to see other vehicles and the conditions inside the tunnel, and also enables vehicles behind to see the vehicle in front. Driving in a tunnel without turning on the lights poses certain safety hazards.
11
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.