What do the numbers on the rear of an Audi represent?

1 Answers
LeMalachi
07/30/25 3:44am
The numbers on the rear of an Audi represent the vehicle's acceleration capability, calculated through a complex formula. The larger the number, the greater the acceleration and power of the vehicle. Audi is a German automobile manufacturer that produces a variety of sedans and SUVs, many of which are now manufactured domestically. The Audi A3 is a compact car in Audi's lineup, available in both hatchback and sedan versions. In terms of power, the Audi A3 is equipped with two engines: a 1.4-liter turbocharged engine and a 2.0-liter turbocharged engine. The 1.4-liter turbocharged engine delivers a maximum torque of 150 horsepower and 250 Nm, while the 2.0-liter turbocharged engine produces a maximum torque of 190 horsepower and 320 Nm.
Was this review help?
4
3
Share
More Forum Discussions

What Types of Batteries Are Used in Current Electric Vehicles?

Electric vehicles are powered by on-board energy sources, use electric motors to drive the wheels, and comply with all road traffic and safety regulations. The batteries used in electric vehicles are either storage batteries or fuel cells. Below is more detailed information about these batteries: 1. Storage batteries are suitable for pure electric vehicles and include lead-acid batteries, nickel-metal hydride batteries, sodium-sulfur batteries, secondary lithium batteries, air batteries, and ternary lithium batteries. 2. Fuel cells are specifically used for fuel cell electric vehicles and include alkaline fuel cells, phosphoric acid fuel cells, molten carbonate fuel cells, solid oxide fuel cells, proton exchange membrane fuel cells, and direct methanol fuel cells.
3
2
Share

What does fault code C0048 mean?

Fault code C0048 refers to the brake booster travel sensor, which utilizes the vacuum generated by the engine intake system to assist braking. It is a widely used brake booster device ranging from light-duty to medium-duty vehicles and can be categorized into vacuum boost, hydraulic boost, and pneumatic boost. The functions of vehicle maintenance include: 1. Ensuring the vehicle maintains optimal performance; 2. Improving vehicle efficiency and reducing wear on parts and tires; 3. Enhancing driving safety; 4. Preventing potential hazards caused by vehicle malfunctions; 5. Reducing noise and environmental pollution; 6. Keeping the vehicle's appearance clean and preventing damage.
9
2
Share

What are the methods to prevent tire blowouts in cars?

Methods to prevent tire blowouts in cars include: 1. Regularly inspect tires; 2. Control driving speed; 3. Install run-flat tires. Tires are crucial components of a vehicle, directly contacting the road surface and working with the suspension system to absorb shocks during driving, ensuring good ride comfort and smooth operation. The maintenance methods for car tires are: 1. Regularly check tire pressure; 2. Inspect tires for bulges, cracks, cuts, punctures, or abnormal wear; 3. Remove foreign objects such as stones, metal pieces, or nails from tire treads; 4. Perform wheel alignment or tire balancing.
7
2
Share

Can the Grand Commander use 92-octane gasoline?

No, the manufacturer recommends using 95-octane gasoline for the Grand Commander. Here are the reasons: 1. Choosing the appropriate gasoline grade according to the car manufacturer's requirements can not only extend the engine's service life but also achieve fuel-saving purposes. 2. If a high-compression-ratio vehicle uses low-grade gasoline, it will not only cause damage to the vehicle but also increase fuel consumption. Conversely, using high-grade gasoline in a low-compression-ratio car will not only result in economic waste but also lead to slow ignition, prolonged combustion time, reduced power, and even damage to the exhaust manifold.
18
4
Share

How to Turn on the High Beam of a Vehicle?

To turn on the high beam of a vehicle, push the lever on the left side of the steering wheel forward. Situations requiring the use of high beams include: 1. When driving on poorly lit roads, high beams can be used alternately with low beams; 2. When unfamiliar with the road conditions or needing to read road signs, high beams may be used but should be quickly switched back to low beams; 3. Alternating between high and low beams is recommended when overtaking at night to alert the vehicle ahead; 4. High beams should be turned on when entering a tunnel and switched to low beams in advance when encountering oncoming traffic; 5. When passing sharp curves, slopes, arched bridges, crosswalks, or uncontrolled intersections at night, vehicles should alternate between high and low beams as a signal.
9
5
Share

What is the method for properly depressing the clutch?

The method for properly depressing the clutch is: 1. When depressing the clutch, use the ball of your foot to ensure stability and completeness; 2. When preparing to start or shift gears, depress the clutch quickly, avoiding slow or intermittent pressing; 3. After depressing the clutch and shifting gears, release the clutch slowly; 4. When starting on a slope, the vehicle may shake slightly—slowly release the clutch before applying the throttle; 5. When the clutch is not in use, always remove your foot from the clutch pedal. The functions of the car clutch are: 1. Ensuring smooth vehicle startup; 2. Facilitating gear shifting; 3. Preventing overload of the transmission system; 4. Reducing torsional vibration impact.
10
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.