What do F and E mean in the fuel tank?

1 Answers
JulietteFitz
07/29/25 5:52am
The letters E and F on the fuel tank represent the capacity of the automobile fuel tank. On the fuel gauge of the car dashboard, the characters E and F are used to indicate the fuel level, where F stands for Full and E stands for Empty. Fuel tank maintenance: Drain accumulated water and sediment from the tank, check for oil leaks at pipe joints and switches; For fuel tank caps equipped with air valves and steam valves, also inspect whether the vent holes are clear; The filter screen at the fuel filler inlet should remain intact to prevent impurities from entering the tank during refueling and clogging the fuel lines; The sealing gasket on the fuel filler cap should also be in good condition to avoid fuel spillage while driving. Precautions for refueling: Try not to wait until the fuel warning light comes on before refueling. Since the fuel pump is located inside the tank, it generates considerable heat during continuous operation and relies on being submerged in fuel for effective cooling. When the fuel light comes on, it indicates the fuel level has dropped below the pump. Consistently waiting until the light comes on to refuel will shorten the fuel pump's service life. Having too little fuel or running out completely may even cause the fuel pump to burn out.
Was this review help?
1
1
Share
More Forum Discussions

What does it mean to drive a Ferrari with one hand?

Driving a Ferrari with one hand is a joke on the internet, mainly implying the display of the owner's wealth. Hazards of driving with one hand: One-handed driving can lead to misoperation in emergencies and even the risk of losing control. Additionally, performing other operations with the other hand can easily cause distraction while driving. Correct driving method: Hands at the 3 and 9 o'clock positions, which allows for the maximum turning angle and gives the driver the greatest control over the car. Racing drivers operate the same way on the track. Of course, for daily driving, it's advisable to relax slightly. On urban roads with lower speeds, driving can be a bit more relaxed. Otherwise, excessive concentration can lead to fatigue and create certain dangers.
20
4
Share

What are the dimensions of Hongqi vehicles?

Hongqi H5 dimensions: 4945×1845×1470mm (length×width×height), with a wheelbase of 2875mm. The H5 offers superior space experience thanks to its advantageous wheelbase. Hongqi N501 model dimensions: N501 body dimensions: 5555×2018×1578mm with 3435mm wheelbase. This model shares the same platform as the Phantom, surpassing Maybach in class. Note the hood ornament - Hongqi vehicles with large emblems represent the highest class, with only the L-series currently featuring this standing emblem. Hongqi E-HS9 model dimensions: Hongqi E-HS9 measures 5209mm in length, 2010mm in width, 1731mm in height, with a 3110mm wheelbase.
8
5
Share

Is the Lingpai a three-cylinder or four-cylinder?

The Lingpai has both three-cylinder and four-cylinder versions. The three-cylinder version is a pure gasoline model, while the four-cylinder version is a hybrid model. Introduction to three-cylinder engines: A three-cylinder engine is an engine composed of three cylinders. Inside it, three identical single cylinders are arranged on one engine block, sharing a single crankshaft to output power. Its main function is to convert chemical energy into mechanical energy. Introduction to four-cylinder engines: A four-cylinder engine, also known as a four-cylinder motor, is a machine capable of converting one form of energy into another more useful form. It typically converts chemical energy into mechanical energy. Sometimes, the term 'engine' can refer to both the power generation device and the entire machine including the power unit, such as gasoline engines or aircraft engines.
7
0
Share

How to Lock a Car Steering Wheel?

The method to lock a car steering wheel is: After stepping on the brake, gently shake the steering wheel with your left hand while simultaneously turning the key with your right hand. The function of the steering wheel is: to convert the force applied by the driver on the edge of the steering wheel into torque, which is then transmitted to the steering shaft. The steering transmission shaft serves as a connecting piece between the steering gear and the steering shaft, facilitating the generalization of the steering gear, compensating for errors during manufacturing and installation, and ensuring reasonable installation of the steering gear and steering wheel on the vehicle. Precautions for using the steering wheel are: 1. Avoid turning the steering wheel to its extreme limit during turns; 2. Minimize forceful twisting of the steering wheel. The solution for a locked steering wheel is: After stepping on the brake, gently shake the steering wheel with your left hand while simultaneously turning the key with your right hand.
1
1
Share

Why does the brake sometimes make abnormal noises?

The reasons why the brake sometimes makes abnormal noises are: 1. The brake pads are too hard; 2. The brake caliper is rusted; 3. The handbrake cable is not flexible; 4. The brake master cylinder returns slowly; 5. There are metal particles or small gravel between the brake pads and the brake disc; 6. The brake disc or brake drum is excessively worn. Braking, also known as stopping, refers to the action of stopping or reducing the speed of running locomotives, vehicles, other transportation tools, or machinery. The solutions for braking issues are: 1. Check whether there is a problem with the lubrication of the top rubber or buffer rubber of the shock absorber; 2. Break in new brake friction pads; 3. Replace the brake pads in time; 4. Clean foreign objects on the surface of the brake disc.
2
5
Share

How to Clean the Laser Head of a Car DVD?

The steps to clean the laser head of a car DVD are: 1. Remove the optical drive from the chassis, use tools like a screwdriver to open the outer shell of the optical drive. In the center of the optical drive, there is a small glass-like sphere. Use a clean cotton swab or wrap absorbent cotton around a toothpick, dip it in a small amount of alcohol or distilled water, and gently wipe the surface of the laser head. After wiping, wait for the alcohol to evaporate, then cover the optical drive shell. If the optical drive has been used for a long time and the working environment is dusty, the surface of the laser head can easily accumulate dust. This can weaken the laser beam emitted by the laser head, reduce the error tolerance of the optical drive, impair its disc-reading ability, or even make it unable to read discs. Cleaning the laser head can alleviate or solve such issues.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.