What decals are required for vehicles?

How to Avoid Orange Peel When Spray Painting?

Paint orange peel phenomenon is actually caused by dry spray of paint, mainly due to high paint viscosity. Here are specific methods to prevent orange peel when spray painting: 1. Thinner: Appropriately add matching special thinner; also, properly reduce the spray gun pressure; the distance between the nozzle and the painted surface should be about 30cm, and spray vertically. 2. Hardener: Adding too much hardener may also cause orange peel, so the amount of hardener should be appropriately reduced. 3. Adjust boiling point: If the temperature of the painted surface or the ambient temperature is too high, causing the thinner to evaporate too quickly after spraying, leading to resin loss and pigment accumulation, resulting in orange peel, adjusting the ratio of thinners with different boiling points can alleviate this phenomenon.

9

5

Share

Is it possible to shift into N gear when driving downhill with an automatic transmission car?

It is not recommended to shift into N gear when driving downhill with an automatic transmission car. Reasons are as follows: When the automatic transmission is in N gear, the transmission and engine are separated, causing the vehicle to lose the engine's drag force. Under the influence of gravity, the vehicle will slide faster and faster, putting significant pressure on the braking system and even risking loss of control. When the vehicle is coasting downhill in N gear, the output shaft of the transmission will rotate at high speed due to the reverse driving force of the wheels. This requires sufficient transmission fluid for cooling and lubrication. However, the transmission oil pump is driven by the engine, which is only idling at this time. The low rotation speed cannot supply enough fluid to the transmission, leading to insufficient lubrication, increased temperature, and accelerated wear. When in N gear, although the multi-plate clutch between the engine and transmission is separated, the gap is very small. The clutch plates on the transmission side rotate at high speed, while those on the engine side rotate at low speed. This close proximity can easily cause resonance or sliding friction, damaging the clutch plates. Correct operation when driving downhill: When driving downhill with an automatic transmission car, you can switch to manual mode and keep the gear low to control the speed within a manageable range. Using low gear in combination with braking can avoid prolonged braking that may lead to brake failure. When entering a curve, apply the brakes to complete the turn, then release the brakes and use low gear again after the turn.

1

2

Share

How to Properly Place Your Feet on the Brake and Accelerator in an Automatic Transmission Car?

When driving an automatic transmission vehicle, it is best for the driver to keep the right foot positioned in the middle behind the brake and accelerator pedals. Below are specific details on foot placement for drivers: 1. Right Foot: The right foot should always be placed in the middle behind the brake and accelerator pedals. This positioning makes it easier to step on the brake in case of an emergency and also facilitates accelerating the car. Tilting the foot to the right reaches the accelerator pedal, while pressing straight down activates the brake pedal. 2. Precautions: Avoid using the left foot for braking and the right foot for accelerating, as this can lead to simultaneously pressing both pedals, wasting fuel and making operation difficult. 3. Correct Movement: The proper technique for pressing the accelerator and brake involves pivoting the right foot at the heel, moving it left and right to press the pedals without lifting the heel off the floor.

13

1

Share

What is the recommended engine oil specification for the BYD F3 maintenance manual?

BYD F3 maintenance manual recommends using 10W-30SG engine oil. Introduction to BYD F3 engine oil selection is as follows: 1. Engine oil is an important factor affecting engine performance and service life. The BYD F3 is factory-filled with high-quality multi-viscosity oil, specifically 10W-30SG, which can be used year-round except in extremely cold climates. 2. The principle for purchasing engine oil is "there is no best, only the most suitable oil." It is first recommended to use the model recommended by the vehicle manufacturer. When purchasing engine oil, be sure to select the corresponding specification. As for the oil viscosity grade, simply follow the manufacturer's recommendations. 3. If the manufacturer does not specify otherwise, you can refer to the driving environment to choose engine oil. Generally speaking, commonly available oils such as 0W-40, 5W-30, and 5W-40 have strong applicability and can suit most climate conditions in China and the usage requirements of most vehicles.

14

0

Share

How Often Should Car Refrigerant Be Replenished?

Refrigerant, also known as coolant or freon, typically needs to be replenished every 5-8 years when the car's air conditioning system is functioning normally. Refrigerant, also referred to as coolant or freon, is the medium substance used in various heat engines to facilitate energy conversion. These substances usually undergo reversible phase changes (such as gas-liquid phase transitions) to increase power output. Examples include steam in steam engines and refrigerant in refrigeration systems. In refrigeration systems, refrigerant controls the thermodynamic cycle. It absorbs heat from the cooled object at low temperatures and then transfers it to cooling water or air at higher temperatures. In vapor-compression refrigeration systems, refrigerants are working fluids that can liquefy at normal or lower temperatures, such as Freon (fluorine, chlorine, and bromine derivatives of saturated hydrocarbons), azeotropic mixtures (azeotropic solutions formed by mixing two types of Freon in a certain ratio), hydrocarbons (propane, ethylene, etc.), and ammonia. The main technical indicators of refrigerants include saturated vapor pressure, specific heat, viscosity, thermal conductivity, and surface tension. Since the 1960s, extensive research has been conducted on the application of non-azeotropic mixtures, which have been used in natural gas liquefaction and separation, among other areas.

9

2

Share

How to Deal with Frost on Car Windows?

Here are the solutions for frost on car windows: 1. Ventilate before locking the car. Frost forms on the windows due to moisture inside the car. After parking, open the windows for about five minutes to effectively reduce frost. 2. Use a hot towel to wipe off the frost. If you're in a hurry to drive, you can use a hot towel to remove the frost. 3. Warm up the car in advance. Before heading out, start the car early to keep the interior warm. 4. Use an anti-fog spray for cars, which can effectively prevent and remove frost. 5. Cover the car with a car cover after parking at night.

3

0

Share

What decals are required for vehicles?

How to Avoid Orange Peel When Spray Painting?

Is it possible to shift into N gear when driving downhill with an automatic transmission car?

How to Properly Place Your Feet on the Brake and Accelerator in an Automatic Transmission Car?

What is the recommended engine oil specification for the BYD F3 maintenance manual?

How Often Should Car Refrigerant Be Replenished?

How to Deal with Frost on Car Windows?

What causes the car to fail to start when the brake light is on?

Why does the car feel more powerful after changing the transmission oil?

What is toe-in of steering wheels?

How to Polish a Car?