What Damages Can Heavy Rain Cause to a Car?

2 Answers
DiGabrielle
07/29/25 8:09am
Heavy rain can cause the following damages to a car: 1. Damage to the car body: When rainwater mixes with dirt and sludge to form contaminants that adhere to gaps, inadequate cleaning can lead to rust on the car body. 2. Damage to the paint surface: Rainwater in urban areas generally has high acidity, and the acidic components in the rain can severely corrode the car's paint surface, causing difficult-to-repair damage. 3. Damage to the interior: As the vehicle ages, the sealing strips at the body joints will gradually deteriorate. 4. Damage to the ignition system: On rainy days, when cold air outside meets the hot air in the engine compartment, condensation forms on the ignition system. If the moisture cannot evaporate in time, it can affect the operation of the ignition system, leading to symptoms of difficult ignition in the vehicle.
Was this review help?
11
3
Share
MacPaul
08/12/25 11:22am
Heavy rain can cause quite a lot of damage to cars. If water floods into the engine compartment, it may lead to hydro-lock and costly repairs – I've even seen cars being towed away. Rainwater can easily seep into electrical systems, causing short circuits that may fry components like the AC, audio system, or engine control unit. Tires wear out faster on wet roads, braking distances increase, and hydroplaning accidents may occur. In the long run, contaminants in rainwater accelerate metal rusting and severe chassis corrosion, shortening the vehicle's lifespan. After every heavy rain, I recommend washing the car to remove sludge, clearing drainage holes, and checking for aged seals. Prevention is always the best approach.
Was this review help?
14
0
Share
Expand All
More Forum Discussions

How Long Does It Usually Take from Production Scheduling to Vehicle Delivery?

Generally, domestic non-popular models are available within about a month, while domestic popular models with price premiums take one to three months, and imported models take around three months. From production scheduling to vehicle pickup, it usually takes about half a month. When picking up a new car, never just pursue speed—you must carefully inspect the vehicle to avoid receiving an outdated or problematic car. Introduction 1: When picking up the car, be sure to check if the vehicle certificates, invoice, and compliance certificate are complete. Verify that the vehicle documents match the engine identification number on the windshield, and check the production date—this is very important. Introduction 2: Additionally, always inspect the overall exterior of the car in a well-lit area to spot minor flaws. Check for paint scratches, noticeable color differences, tires, the engine, etc. Introduction 3: Inspect the car's interior and configurations to ensure they function properly and match the specifications. This mainly includes the vehicle's electronic devices, lights, seats, windows, and other components.
16
2
Share

Is the RAV4 the same as the Rongfang?

RAV4 is the Rongfang. The RAV4 was the previous generation of the Rongfang, and after the facelift, it was renamed to the Chinese name Rongfang. The Rongfang is a compact SUV under Toyota, and this model is equipped with naturally aspirated engines across the entire lineup. The Rongfang uses two engines in total: one is a 2.0-liter naturally aspirated engine, and the other is a 2.5-liter naturally aspirated engine. Below are the details of these two engines: 1. Rongfang 2.0-liter naturally aspirated engine: This engine delivers 171 horsepower and a maximum torque of 209 Nm, reaching its maximum power output at 6,600 rpm and maximum torque between 4,400 and 5,000 rpm. The engine features hybrid injection technology and uses an aluminum alloy cylinder head and block. It is paired with a CVT transmission. 2. Rongfang 2.5-liter naturally aspirated engine: This engine produces 178 horsepower and a maximum torque of 221 Nm, achieving maximum power output at 5,700 rpm and maximum torque between 3,600 and 5,200 rpm. The engine also features hybrid injection technology and uses an aluminum alloy cylinder head and block.
8
5
Share

What is the speed of a car?

The speed of a car should generally be between 30-60 km/h when driving in urban areas, around 80-120 km/h on highways, and approximately 60-80 km/h in ordinary urban areas. Due to the higher density of vehicles in urban areas, it is advisable to maintain a steady speed of around 40 km/h. Below are specific details about the maximum speed of a car: 1. Detail one: During the break-in period of a new car, the speed should not be too high, usually controlled between 50-90 km/h, with some models allowing slightly higher speeds. The maximum speed during the break-in period can be controlled within 110 km/h. 2. Detail two: Additionally, it is important to control the engine's RPM, which is best kept between 2000-2500 RPM. 3. Detail three: It is crucial to avoid high engine RPMs and to drive gently. During the break-in period, the speed should not exceed 100 km/h, and the RPM should not exceed 2500.
14
2
Share

Will Milk Spoil If Left in a Hot Car?

Milk left in a hot car can potentially spoil within half a day, and in hotter weather, it may spoil in as little as 2 hours. The temperature in a car's trunk is generally even higher than the outside temperature, which is akin to simmering milk without letting it boil, making it highly prone to spoilage. Below are the hazards of high car temperatures: 1. Hazard One: The higher the temperature, the hotter the engine compartment becomes, increasing the likelihood of vapor lock, especially when the car is fully loaded climbing a slope or driving at low speed for extended periods. 2. Hazard Two: Another issue is abnormal ignition. When driving in high-temperature environments, the ignition coil can overheat, weakening the high-voltage spark, which may lead to engine misfire at high speeds. In severe cases, this can burn out the ignition coil, affecting the vehicle's normal operation.
2
4
Share

Does the Changan CS85 have four-wheel drive?

The currently available models of the Changan CS85 do not include a four-wheel-drive version. However, a four-wheel-drive variant will be offered in the future for consumers to choose from. The Changan CS85 features a chassis tuned with a front MacPherson and rear multi-link independent suspension system, ensuring four-wheel independent movement and leading suspension performance in the domestic market. This setup guarantees stable body control and a comfortable ride across various road conditions. Introduction to the Changan CS85: 1. The suspension system has undergone multiple rounds of fine-tuning, utilizing high-end valve structures from renowned shock absorber suppliers to achieve a perfect balance between handling and comfort, delivering users an ultimate experience of 'effortless driving, free-spirited control, and comfortable quality.' 2. In terms of appearance, the new car adopts Changan's latest generation of family design language, featuring a striking butterfly-wing front face design. The headlights, grille, and front bumper blend seamlessly, creating a strong visual impact. 3. The interior of the grille is composed of multiple horizontal chrome strips, paired with sharp-looking headlight clusters, resulting in a dazzling effect. Additionally, the slightly shovel-shaped front bumper design at the lower part of the front face enhances the car's sporty feel. 4. Regarding dimensions, the car measures 4720mm in length, 1845mm in width, and 1665mm in height, with a wheelbase of 2705mm.
12
5
Share

How to Turn on the Lights Inside a BMW 5 Series?

To turn on the lights inside a BMW 5 Series, follow these steps: 1. Turn Signals and Parking Lights: The lights can only be activated after the vehicle is started. The method is simple—just rotate the button on the light control lever to turn on the corresponding lights. (1) Left Turn Signal: Push the control lever downward to activate the left turn signal. (2) Right Turn Signal: Push the control lever upward to activate the right turn signal. A light tap on the lever will make the corresponding turn signal flash three times before automatically turning off. 2. High Beam and High Beam Flash Function: (1) High Beam: First, turn the light knob to the low beam position, then push the light control lever forward to activate the high beam. (2) High Beam Flash: After turning on the headlights, pull the light control lever backward once to activate the high-low beam alternation, which serves as an effective warning signal. The high beam indicator will illuminate on the instrument panel. 3. Fog Lights: The fog light switch is located next to the light knob—simply press it to turn on. 4. Automatic Headlights, Low Beam, and Position Lights: Automatic headlights can be enabled via the central control settings. Rotate the light control button sequentially to activate the position lights, automatic headlights, and low beam in order. 5. Headlight Washer: With the headlights on, activate the windshield washer switch to clean the headlights. If you only want to clean the windshield, turn off the headlights before using the washer switch. 6. Adaptive Headlights: Activation Method: Press the light symbol button with the letter "A" on the left steering column lever.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.