What could be the reason for a roaring sound inside the car that doesn't feel like tire noise?

2 Answers
LaAllie
09/05/25 8:14am
The reasons for a roaring sound inside the car that doesn't feel like tire noise are: 1. Engine carbon deposits causing body resonance; 2. Blockage in the three-way catalytic converter; 3. Use of engine oil with incorrect viscosity grade or excessively high oil grade; 4. Dirty air filter or aging/leaking vacuum tubes. Common types of car noises include: 1. Engine noise, which mostly occurs in older vehicles, improper maintenance, or when there are issues in the engine compartment; 2. Interior noise, sometimes caused by loose items inside the car; 3. Noise from road gravel; 4. Chassis noise, indicating problems with the vehicle's structural framework.
Was this review help?
20
2
Share
MacBrooke
09/17/25 8:25am
I've been driving for over a decade and encountered this roaring noise several times, usually caused by bad wheel bearings. The sound is particularly noticeable at high speeds, getting louder with higher RPMs, and changes slightly when turning. It's quite different from the consistent hum of tire noise. Last time my car had a similar issue, the diagnosis was rear wheel bearing wear causing wheel wobble. Getting it replaced promptly solves the problem at a reasonable cost, just a few hundred bucks. But don't delay, as a seized bearing could potentially cause tire detachment, which is extremely dangerous. I suggest you pay attention during your next drive: accelerate past 70 to see if the roar intensifies, and listen for sound variations when turning. After this preliminary check, visit a reputable repair shop to have them lift the car and spin the wheels for testing - they can confirm the issue within minutes. Don't forget to check bearing lifespan during routine maintenance either, as 50,000 kilometers is typically a critical threshold.
Was this review help?
6
5
Share
Expand All
More Forum Discussions

What to Do When a Car's Motor Has No Power and Won't Start?

When a car's motor has no power and won't start, you can use the push-start method or the jump-start method. Below are the introductions to these two methods: 1. Push-start method (only for manual transmission cars): This method is commonly seen and is only applicable to manual transmission cars. It involves gathering several people to push the car to get it started. Once the car reaches a certain speed, engage the gear and quickly release the clutch pedal while pressing the accelerator. As soon as the engine starts, quickly press the clutch pedal again and control the throttle to prevent the engine from stalling, then slowly pull over to park. 2. Jump-start method: For this method, you first need another car with a charged battery nearby and a set of jumper cables. Bring the two cars close together, open the hood to locate the other car's battery, and connect the two batteries using the jumper cables. Follow the specific steps below carefully. If you're not confident, it's better to seek help from a professional or a specialized service.
6
5
Share

How to Reset the Oil Maintenance Light on BAIC BJ80C?

BAIC BJ80C oil maintenance light can be reset using a fault diagnostic tool. Additional information: 1. Function of the car maintenance light: The original intention of the car maintenance light is to remind the owner to perform maintenance as soon as possible. Therefore, the owner should promptly go to the 4S shop for maintenance. After the maintenance is completed, the 4S shop will use a fault diagnostic tool to reset the maintenance light for the vehicle. 2. Definition of maintenance light reset: Most vehicle models have a maintenance light reminder function on the instrument panel. After driving a certain mileage or period of time, the LCD screen on the instrument panel will display a message prompting immediate maintenance. This means that the mileage or number of days the car has been driven has reached the time for replacing the three filters and oil. After replacing the three filters and oil, it is necessary to reset the system to allow the computer to re-memorize the next maintenance mileage or number of days, commonly known as maintenance light reset.
19
5
Share

What are the reasons for the plunger pump failing to build up pressure?

The reasons for the plunger pump failing to build up pressure are: 1. The filter on the suction line is clogged; 2. The oil level in the hydraulic tank is too low; 3. The R-angle of the variable mechanism is too small, resulting in insufficient flow, combined with the effect of internal leakage, thus unable to continuously supply pressurized oil externally; 4. Severe damage to the contact surface between the distribution plate and the cylinder block, poor sealing, or initial poor sealing between the cylinder block and the distribution plate; 5. Severe wear between the plunger outer diameter and the cylinder bore, serious oil leakage, or insufficient driving power. The plunger pump is an important device in the hydraulic system, relying on the reciprocating movement of the plunger in the cylinder to change the volume of the sealed working chamber for oil suction and pressurization. The plunger pump has the advantages of high rated pressure, compact structure, high efficiency, and convenient flow regulation, and is widely used in applications requiring high pressure, large flow, and adjustable flow.
4
1
Share

How much engine oil does the Touareg require?

The Volkswagen Touareg with the 3.0T engine requires 7 liters of engine oil, while the 2.0T model needs 5 liters. Engine oil helps reduce fuel consumption, lower exhaust emissions, and extend the lifespan of the catalytic converter. It offers strong high-temperature oxidation resistance, providing appropriate lubrication and effective protection for the engine under various harsh operating conditions, thereby extending its service life and reducing dry wear during engine startup. The 2.0-liter turbocharged engine delivers 245 horsepower and a maximum torque of 370 Nm, with a maximum power output at 5000 to 6500 rpm and peak torque available between 1600 to 4300 rpm. It features hybrid injection technology and uses an aluminum cylinder head with a cast iron block. This engine is paired with an 8-speed automatic transmission. The 3.0-liter turbocharged engine produces 340 horsepower and a maximum torque of 450 Nm, achieving peak power at 5300 to 6400 rpm and maximum torque between 1340 to 5300 rpm. It employs direct fuel injection technology and utilizes an aluminum cylinder head and block. This engine is also matched with an 8-speed automatic transmission.
4
0
Share

How to Determine Abnormal Noise from Car Wheel Bearings?

If the wheel bearing is damaged, the wheel will emit a noisy abnormal sound during vehicle operation. Lift the vehicle and manually rock the wheel left and right to check for any bearing clearance.
10
2
Share

What is the best way to repair a car tire puncture?

Methods for repairing car tire punctures are as follows: 1. Plug repair: This is the earliest and most traditional method of tire repair. The process involves inserting a rubber plug into the puncture hole of the tire. Once the air leakage stops, the repair is complete. The drawbacks are quite obvious. While the original puncture might have been caused by a small nail creating a tiny hole, to fit the plug, the hole needs to be enlarged further. This method can be quite damaging to the tire. 2. Mushroom plug repair: The mushroom plug resembles a large tack but has a long rubber strip in the middle. It is applied from the inside of the tire, with the rubber strip pushed through to the outside. The large patch is then firmly attached to the inside of the tire, and the excess part protruding outside is trimmed off. This method provides good protection for both the inner and outer surfaces of the tire. The downside is that it is the most expensive among tire repair methods, but it also offers the best results. 3. Cold patch repair: This method requires removing the tire from the rim, grinding off a layer on the inside of the tire, and then applying a new patch. This type of repair offers high stability, and the tire can be used normally without any issues.
6
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.