What Constitutes a Violation When Yielding to Pedestrians?

1 Answers
Marty
07/29/25 12:29pm
Crossing during your prohibited time at an intersection, failing to stop and yield to pedestrians when passing through crosswalks, or near schools, villages, towns, or crowded market areas are all considered violations. Below is an introduction regarding yielding to pedestrians: 1. When encountering pedestrians crossing at a crosswalk: Vehicles must stop and yield when approaching a crosswalk where pedestrians are crossing. If there are double yellow lines or barriers in the center of the road without greenery separation, vehicles must yield once pedestrians step onto the crosswalk. 2. In the absence of traffic signals or crosswalks: When driving on roads without traffic signals, vehicles must yield to pedestrians crossing the road.
Was this review help?
20
1
Share
More Forum Discussions

What are the reasons why an electric vehicle cannot start?

Reasons why an electric vehicle cannot start: 1. The battery is dead; 2. The controller is damaged; 3. There is a circuit malfunction. After encountering this situation, it is necessary to go to a professional repair facility for inspection and repair. Electric vehicles refer to vehicles that use electrical energy as a power source and are driven by electric motors. They belong to the category of new energy vehicles, including pure electric vehicles (BEV), hybrid electric vehicles (HEV), and fuel cell electric vehicles. Taking pure electric vehicles as an example, they are vehicles driven by electric motors. Compared to fuel-powered vehicles, the main differences of pure electric vehicles lie in four major components: the drive motor, speed controller, power battery, and onboard charger.
3
2
Share

What does the warning light on the Changan Kuayue Wang X1 indicate?

Warning light illumination indicates a fault in the electronic control system components or wiring. Below is relevant information about the Changan Kuayue Wang: 1. Vehicle Design: Compared to traditional single wheels, the dual-wheel design increases width, expands the contact area, reduces ground pressure, and thereby enhances the vehicle's load capacity. Additionally, the dual-wheel configuration provides a wider wheelbase, ensuring driving stability. 2. Power: In terms of powertrain, the Kuayue Wang X1 is equipped with a robust 88-horsepower engine. This power configuration fully meets daily cargo transportation needs. Moreover, the Kuayue Wang X1's powertrain emissions fully comply with China VI emission standards while being fuel-efficient, with a combined fuel consumption of only 7.3L/100km.
3
2
Share

What is the maximum speed of the Audi A3 during the break-in period?

The maximum speed of the Audi A3 during the break-in period is 100 kilometers per hour. The break-in period refers to the initial driving distance after a new car leaves the factory, during which the engine components are allowed to wear in smoothly. The Audi A3 is a 5-door, 5-seat hatchback with the following dimensions: length 4351mm, width 1815mm, height 1458mm, wheelbase 2630mm, and a curb weight of 1400kg. The Audi A3 is equipped with a 1.4L turbocharged engine, delivering a maximum horsepower of 150PS and a maximum power of 110kW, paired with a 7-speed dual-clutch transmission.
10
3
Share

How to Remove the License Plate Light on a Bluebird?

To remove the license plate light on a Bluebird, follow these steps: 1. You will need a flathead screwdriver to remove the license plate light. Locate the clip of the license plate light and gently pry it open. 2. Twist the rear connection clockwise, then remove and replace the bulb. Additional information about the license plate light: 1. The license plate light is used to illuminate the license plate at night or in low-light conditions, and it is turned on together with the parking lights. 2. According to regulations, all vehicles must have their rear license plate lights turned on while driving at night. The brightness of the rear license plate light must allow a person with normal vision to clearly read the license plate number from within 20 meters at night. The license plate light must also be controlled by the same switch as the parking lights.
14
1
Share

Where to Find the Manufacturing Date of the Envision?

There is an automotive nameplate on the door frame of the passenger side, which indicates the manufacturing date. Vehicles must be equipped with a product nameplate, placed in an easily observable location at the front of the vehicle. Introduction to the Vehicle Nameplate: The vehicle nameplate is a label that indicates the basic characteristics of the vehicle, including the brand, model, engine power, total weight, load capacity or passenger capacity, manufacturing number, manufacturing date, and manufacturer name. Function of the Vehicle Nameplate: The manufacturing date can be confirmed by inquiring with the user or by checking the vehicle nameplate, as the vehicle nameplate in the driver's compartment will always display the manufacturing date.
1
4
Share

What are the effects of driving with the handbrake on?

Driving with the handbrake on has the following effects on the vehicle: it accelerates the wear of the brake discs, and the brake pads may harden due to overheating, leading to reduced handbrake performance and elongation of the handbrake cable. The handbrake, also known as the auxiliary brake, is a crucial component of the vehicle's braking system. Proper use of the handbrake can effectively prevent the vehicle from rolling and reduce the danger of rolling when parked. The functions of the handbrake are: 1. When parking, pulling the handbrake keeps the vehicle stationary and prevents it from rolling downhill; 2. During driving, applying the handbrake while turning can create a drifting effect; 3. In emergency situations, the handbrake can be used as a brake.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.