What class of car is the Infiniti Q70?

What is the principle of the EGR valve?

EGR valve is the exhaust gas recirculation valve, a mechatronic product installed on diesel engines to control the amount of exhaust gas recirculated back into the intake system. Its working principle is as follows: 1. The EGR valve stem rises, pushing the connected sliding contact arm to change position, causing the sliding contact to move along the sliding resistor, generating different voltage signals. These signals are transmitted to the engine control ECU, which monitors the position of the EGR valve to ensure the valve responds correctly to ECU commands. This adjusts and corrects the opening timing and duty cycle of the EGR valve, precisely controlling the recirculation volume to reduce emissions and improve performance. 2. EGR stands for Exhaust Gas Recirculation system, and the EGR valve is a key control component in the entire EGR system. The EGR valve is installed on the intake pipe. Exhaust gas recirculation (EGR valve) introduces exhaust gas into the intake pipe, reducing the oxygen content in the intake air, thereby lowering combustion temperature and reducing nitrogen oxide emissions.

2

1

Share

What does it mean when the temperature gauge light comes on?

The temperature gauge light coming on indicates a fault in the engine's cooling system, which fails to ensure proper cooling of the engine. When the temperature gauge light is on, it not only causes wear and tear on internal engine components but may even lead to cylinder scuffing. Therefore, it is crucial to identify the cause when the temperature gauge light illuminates. The primary reason for the temperature gauge light coming on is insufficient coolant in the car's radiator, which needs to be replenished promptly. Steps to replenish coolant: 1. Ensure the engine is in a cold state; 2. Open the hood, locate the engine's coolant reservoir, and unscrew the radiator cap counterclockwise; 3. Directly add the same specification of coolant to the radiator until the liquid level reaches the maximum mark; 4. After replenishing the coolant, simply close the radiator cap.

15

2

Share

How to Switch to Recirculation Mode?

You can switch between modes by operating the buttons according to your vehicle model. Some models use a single button to switch, while others use two buttons. Below is a detailed introduction to the functions of the recirculation and fresh air modes: 1. The fresh air mode serves to replenish fresh air. 2. The recirculation mode blocks out polluted air. Here are some precautions for using these modes: 1. Shortly after entering the car, you should open the windows or activate the fresh air ventilation system to introduce fresh air. Avoid driving for long periods with the windows and doors closed, and never sleep or rest for extended periods in a sealed car. 2. After purchasing a new car, make efforts to exchange air between the inside and outside of the car, similar to airing out a newly renovated house, to allow harmful gases inside the car to evaporate and dissipate as soon as possible. 3. When using the air conditioning or heating, opt for the air exchange mode between the inside and outside of the car, and try to avoid using the recirculation mode for extended periods. 4. Be mindful of choosing routes with relatively good air quality, just as you would choose low-pollution green products. Whenever possible, drive on open roads with good air circulation. 5. In areas or times with heavy traffic, or when following vehicles that may have excessive exhaust emissions, temporarily switch the air conditioning or heating to recirculation mode. If driving with windows open, temporarily close them. Car owners should develop the habit of adjusting the car's air circulation system promptly based on the outside air conditions. 6. For the first six months of a new car, ensure enhanced ventilation, regularly clean the car's air conditioning system, and strive to maintain fresh air inside the car. Pay special attention not to use perfumes or air fresheners to mask unusual odors inside the car.

20

1

Share

Why Does a Car Burn Antifreeze?

Antifreeze is primarily used in the cooling system of liquid-cooled engines. It offers excellent performance in preventing freezing in winter, boiling in summer, and protecting against scale and corrosion throughout the year. Method for Replacing Antifreeze: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with a particular focus on the five-way hose. The five-way hose gets its name from having five connection points to various parts. Antifreeze flows through the five-way hose and is distributed to different parts of the car to perform its function. If there is any leakage of antifreeze in this section, replace the hose or resecure the connection as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir and continue filling it until water flows continuously through the engine cooling system. Then, start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially flowing out of the reservoir will have a faint pink tint. Keep adding clean water until the outflow is clear. Note: Remember to remove the heater hose and drain the water from the heater core. About an hour after draining, add the new antifreeze through the radiator hose to allow it to flow quickly into the radiator. Then, add another container of antifreeze to the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is purged from the system. Top up the antifreeze to the "MAXT" mark on the reservoir.

11

3

Share

What does screw M5 M6 mean?

Screw M5 and M6 refer to screws with diameters of 5 millimeters and 6 millimeters respectively. Here are the specific details: 1. Complete labeling: The letter represents the type of thread, and the number represents the nominal diameter. The complete labeling should also include the thread pitch, thread length, rotation direction, and when necessary, the thread fit tolerance, manufacturing tolerance grade, and surface treatment of the nut and screw. 2. Precautions: If the wear of the screw exceeds 10% during use, the screw should be stopped immediately. Forcing the use of such screws can easily lead to safety accidents, so special attention must be paid.

20

0

Share

What is the reason for the engine malfunction light being on but the car can still run normally?

The reason for the engine malfunction light being on but the car can still run normally is that the car needs maintenance such as an oil change. The engine malfunction light on the dashboard, usually red or yellow, will not automatically disappear in most cases once it lights up, though it may disappear on its own in rare instances. This is what is referred to as the engine malfunction light. If there is a current engine system fault, it should be checked and repaired promptly. Additionally, the fault information will be stored and provided as a reference to the car maintenance supervisor during repairs to resolve the issue more quickly. To ensure the engine can continue running when a fault occurs, if the detected fault has minimal impact on the engine's operation, the computer will ignore it. However, in reality, the engine is not in good working condition under such circumstances.

13

1

Share

What class of car is the Infiniti Q70?

What is the principle of the EGR valve?

What does it mean when the temperature gauge light comes on?

How to Switch to Recirculation Mode?

Why Does a Car Burn Antifreeze?

What does screw M5 M6 mean?

What is the reason for the engine malfunction light being on but the car can still run normally?

Should You Use Cold or Hot Air to Defrost Your Car?

What Causes the Wiper to Stop Moving?

What are the steps for Santana remote control pairing?

What brand is the Edge's 8AT transmission?