What Causes Weak Ignition in Cars?

1 Answers
FranciscoAnn
07/24/25 2:47pm
Here are the reasons for weak car ignition: 1. Pay attention to the battery: Generally, green indicates normal power, white indicates the need for charging maintenance, and red indicates a dead battery (some may use green for qualified, black for low power, and white for battery damage requiring replacement). The lifespan of a battery is typically around two years. If the battery power is found to be low, it should be replaced promptly. 2. Pay attention to the throttle valve body and idle valve: Carbon buildup in the throttle valve body and idle valve can cause difficulty in starting. For vehicles with an idle valve, lightly pressing the accelerator pedal before starting can help ignite the engine, but releasing the pedal may cause immediate stalling. Therefore, it's best to promptly visit a repair shop for cleaning and inspection. Additionally, during maintenance, it's essential to frequently replace the air filter. In northern areas with more dust, the air filter should be replaced every 10,000 kilometers, and even more frequently on sandy or dusty roads. 3. Fuel pressure: To ensure normal engine startup, the residual fuel pressure in the fuel system after the engine is turned off should not be below 2.5–3.5 kg/cm². Otherwise, insufficient pressure will prevent the fuel injector from spraying enough fuel for startup. Repeatedly turning the ignition switch can restore the fuel pressure to normal, making startup much easier. However, it's best to have a professional mechanic inspect the fuel system to rule out any faults. 4. Lubricant quality: As winter approaches, it's important to replace all lubricants, including engine oil, transmission oil, and power steering fluid, as ordinary lubricants become more viscous and less fluid in cold weather, increasing friction resistance and making cold starts difficult. Choosing a slightly less viscous oil can reduce mechanical wear and protect the engine.
Was this review help?
9
0
Share
More Forum Discussions

What is the National Emission Standard for VI?

VI refers to China VI, where VI stands for the Roman numeral six. Below is relevant information about China VI: 1. Compared to China V fuels, China VI fuels can reduce particulate emissions by up to 10%, significantly decreasing pollutant levels in vehicle exhaust. 2. The China VI emission standard represents a 40%~50% improvement over the current China V standard, surpassing Euro 6 standards and being comparable to U.S. levels. 3. Under the China VI standard, the upper limits for aromatic hydrocarbon content in ethanol gasoline are reduced by 12.5%, olefin content by 25%, and benzene content by 20%.
20
5
Share

How to Determine When Fuel Injectors Need Cleaning?

When fuel injectors become dirty, the car will exhibit the following noticeable symptoms: 1. Increased engine noise, especially noticeable at lower gears and below 2500 RPM. 2. Unresponsive throttle, resulting in less smooth driving. There is a noticeable lag after pressing the accelerator, and the engine RPM rises slowly when revving in neutral. 3. Idle vibration, particularly noticeable when starting. There may be slight misfiring when shifting at low gears and low RPM. Here is some information about cleaning: 1. Cleaning interval: Clean every 40,000 to 60,000 kilometers. 2. Price: Cleaning at a 4S shop costs around 1000 RMB.
5
1
Share

How to use the air conditioning in Nissan Qashqai?

Nissan Qashqai air conditioning usage instructions are as follows: 1. Cooling/Heating: Adjust ventilation and fan speed. For cooling, press the "A/C" button (no need for heating), then set the temperature to desired level. 2. Dehumidification/Defogging: Set ventilation mode to front defroster (FRONT), adjust fan speed, and turn on the "A/C" button. Note: For quick defrosting of the windshield exterior, set both temperature and fan speed to maximum. 3. Air conditioning settings: You can set to external circulation mode, adjust ventilation mode, fan speed and temperature.
20
1
Share

What Causes Car Shaking at High Speeds?

High-speed car shaking can be attributed to the following reasons: 1. Uneven brake disc surfaces with excessive radial runout. During braking, the inconsistent contact between brake pads and discs causes fluctuating braking force, resulting in body vibration—especially noticeable during light braking. 2. Significant deviation in wheel alignment data. This makes the vehicle harder to control during acceleration, accompanied by slight vibrations. 3. Improper tire pressure (either too high or too low). Overinflated tires intensify shaking at higher speeds, while underinflated tires cause the vehicle to pull to one side. 4. Abnormal tire wear. Irregular tire surface wear due to misaligned wheels or rim deformation leads to body vibration during driving.
14
4
Share

How to Use the Auto Start-Stop Function in Volkswagen Passat?

Volkswagen Passat's auto start-stop function is located next to the gear lever on the center console and is operated via a mechanical button. Generally, vehicles equipped with an auto start-stop system have this function enabled by default, requiring no additional action. Here are some tips for using the auto start-stop function: 1. Turning it off: The owner needs to manually turn it off each time they drive. To disable it permanently, a visit to a 4S dealership is required for settings adjustment. 2. For vehicles without hill start assist, it's advisable to turn off this function when starting on a slope to prevent the vehicle from rolling backward. 3. During heavy traffic holidays, it's best to disable this function to avoid slower starts.
10
1
Share

How to Remove the Headlight of Touran?

The method for removing the headlight of Touran is as follows: 1. Unplug the power socket of the bulb. When unplugging the bulb's power socket, apply moderate force to avoid loosening the socket wiring or damaging the bulb plug; 2. After disconnecting the power interface, remove the waterproof cover behind the bulb. The waterproof cover of the headlight is mostly made of soft rubber, and some models are equipped with soft plastic waterproof covers, which are no different. Just apply a little force to remove the waterproof cover. 3. Remove the bulb from the reflector. When removing the bulb, use your fingers to pinch the steel wire clips on both sides, and after the bulb is loosened, pull it out; 4. Place the new bulb into the reflector, aligning the fixed positions of the bulb. There are several fixed positions on the bulb base. Install the new bulb by reversing the steps of removing the old bulb: pinch the steel wire clips to insert the bulb into the reflector, align the installation position, and then release the clips to secure the bulb; 5. When covering the waterproof cover, ensure that the edge of the waterproof cover is completely aligned with the fixed position.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.