What Causes Water Leakage Under the Co-Driver Seat in a Car?

2 Answers
AlyssaAnn
07/29/25 11:58pm
Water leakage under the co-driver seat in a car is likely caused by a door leak. Below are related explanations regarding water leakage under the co-driver seat: Solutions: If you hear obvious water sloshing sounds when opening/closing the door or while driving, it indicates water accumulation inside the door. In this case, simply use a thin wire or small screwdriver to unclog the drainage holes—this can be easily done yourself. Detailed scenarios of leakage: If the window regulator has been replaced, it may be due to improper adhesion of the door waterproof membrane after the replacement, as the membrane needs to be peeled off during the regulator replacement process. If the waterproof membrane is not properly sealed, heavy rain can cause water to enter the cabin. You can either reseal it yourself or replace the waterproof membrane.
Was this review help?
19
3
Share
DeAbigail
08/16/25 3:36am
Last time my car's passenger side leaked water and it really confused me, so I checked it out thoroughly. The most common cause is a clogged AC drain pipe—when it's hot and you turn on the AC, the condensed water can't drain out and ends up pouring inside. If the sunroof drain holes are blocked by leaves or mud, rainwater will flow down the A-pillar into the passenger side. Also, if the door seals are cracked or the drain holes are clogged, rainwater can seep into the door panel and then leak onto the floor mats through gaps. A cracked windshield sealant can also cause leaks. You need to carefully inspect all these areas—best to dry them with a cloth and then place a tissue to test for leaks. Don’t delay, as standing water can damage wiring and make repairs much more complicated. You might even end up having to replace the control module under the seats.
Was this review help?
12
5
Share
Expand All
More Forum Discussions

What is the solution for the P0251 fault code in diesel vehicles?

When clearing fault codes, it is essential to strictly follow the specific fault code clearing procedure designated for the particular vehicle model. Under no circumstances should the negative ground cable be disconnected directly to clear the fault code. 1. Meaning of P0251 fault code: The P0251 fault code, applicable to all automobile manufacturers, indicates a malfunction in the fuel metering control A (cam/rotor/injector) of the injection pump. 2. Possible causes: This may include issues with the Fuel Control Actuator (FCA), its circuitry, the injection pump, or the Electronic Control Module (ECU). The Fuel Control Actuator (FCA) is typically located on the rear side of the injection pump and functions as an electronically controlled solenoid valve. The ECU regulates the amount of fuel entering the injection pump by cyclically opening and closing the FCA.
3
0
Share

What Does a BMW Look Like?

The logo features blue sky, white clouds, and a propeller, making its appearance instantly recognizable. The 1 Series is a highly distinctive sporty hatchback, the 3 Series is a pure sports mid-size luxury sedan, the 5 Series is the benchmark for luxury business sedans, the 7 Series is the top-tier flagship luxury car for leaders, the BMW Z4 is the perfect pure convertible sports car, the X Series combines efficient hybrid power with the perfect Xdrive system, and the M Series offers an extreme speed experience integrated with sports aesthetics. Below is a related introduction: Model Range: BMW, fully known in Chinese as Bavarian Motor Works Co., Ltd., is a German automotive brand. BMW's model range includes the i, X, Z, and pure number series (1, 2, 3, 4, 5, 6, 7, 8), along with the M Series (BMW's official high-performance modification division) based on improvements to these series. Founding Date: BMW was founded in 1916 and is headquartered in Munich, Bavaria, Germany. The blue and white logo of BMW represents the colors of the Bavarian state flag. Over the past century, BMW has evolved from an aircraft engine manufacturer into a leading enterprise group specializing in premium cars, as well as globally renowned aircraft engines, off-road vehicles, and motorcycles, ranking among the top automotive companies in the world. Its full name is die Bayerischen Motorenwerke (Bavarian Motor Works).
1
0
Share

Can You Start the Car While Pressing the Clutch?

When starting a manual transmission car, it is necessary to press the clutch pedal to disconnect the engine from the transmission, thereby reducing the load on the starter. While it is possible to start the car without pressing the clutch, doing so increases the burden on the starter, so it is recommended to press the clutch when starting. Introduction to the Clutch: The clutch is a crucial component in a car's drivetrain, located between the engine and the transmission. It can disconnect or connect the engine to the transmission. The clutch pressure plate is fixed to the engine flywheel, with the clutch disc positioned between the pressure plate and the flywheel. The clutch disc has a spline in the center that secures a driveshaft, which serves as the transmission's power input shaft. Important Notes: When the driver presses the clutch pedal, the clutch disengages, and releasing the pedal engages the clutch. The clutch disc is a wear-and-tear part that requires periodic replacement. As the car accumulates mileage, the clutch disc gradually wears out. Once the clutch disc wears beyond a certain point, it must be replaced. Replacing the clutch disc involves disconnecting the engine from the transmission and removing the transmission from the vehicle, as this is the only way to access and replace the clutch disc.
5
0
Share

Should the automatic headlights of the Honda Breeze be turned on during the day?

The automatic headlights of the Honda Breeze can be turned on during the day. When the car enters dimly lit areas such as tunnels or underground parking garages, the headlights will automatically turn on to ensure driving safety. The Honda Breeze is a 5-seater SUV positioned as a compact SUV. More details about the Honda Breeze are as follows: 1. Introduction: The GAC Honda Breeze can be considered a sister model to the Dongfeng Honda CR-V, both positioned as compact SUVs and built on the same platform. 2. Body dimensions: The new car measures 4634×1855×1679mm in length, width, and height, with a wheelbase of 2661mm. 3. Powertrain: It is equipped with an L15BT 1.5T turbocharged engine, delivering a maximum power of 142kW (193PS) and a peak torque of 243N·m, paired with a CVT transmission. The official fuel consumption is 6.4-6.8L/100km.
8
4
Share

Does a New Car Come with Engine Oil and Coolant?

New cars do come with engine oil and coolant, and they are filled to the standard level with sufficient quantities. This is because the vehicle needs to undergo a series of subsequent tests, and without these fluids properly added, the follow-up processes cannot proceed. The method for replacing coolant is as follows: Before completely replacing the coolant, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with special attention to the five-way water pipe. The coolant flows through this pipe and is then distributed to different parts of the car to perform its functions. If there is any coolant leakage in this section, replace the water pipe or resecure the connection as needed. Drain the old coolant, then flush the fluid channels with clean water. Add clean water to the coolant reservoir, then continuously inject water into the reservoir so it circulates through the engine cooling system. Let the engine idle for 3 to 5 minutes to allow the water to circulate. Initially, the water flowing out of the reservoir may have a faint pink tint. Continue adding clean water until the outflowing water runs clear. Note: Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new coolant through the radiator hose. Then, pour another container of coolant into the coolant reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. During this time, the coolant level will drop slightly as air is purged from the cooling system. Top up the coolant again until it reaches the "MAXT" mark on the reservoir.
20
4
Share

How to Replace Old License Plates with New Ones?

You can bring your ID card and vehicle registration certificate to the local vehicle management office for replacement. 1. Materials required for license plate replacement: 'Application Form for Replacement of Motor Vehicle License Plates and Certificates' (fill in the form with a pen or fountain pen, no alterations allowed); vehicle registration certificate; original and copy of the vehicle owner's identity proof; if handled by an authorized agent, the agent's identity proof must also be submitted, and the agent must sign the 'Application Form for Replacement of Motor Vehicle License Plates and Certificates' together with the vehicle owner. 2. Procedure: The vehicle owner or agent should, within 8 working days, present the payment receipt for the replacement of license plates and the 'Vehicle Registration Certificate' to the local vehicle management department to collect the replaced license plates.
4
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.