What Causes Tire Wear?

2 Answers
ValentinaLynn
07/29/25 4:16am
Tire wear can be attributed to the following reasons: 1. Incorrect alignment: The main cause is misaligned front wheel positioning. When the camber angle of the front wheels is too large, the outer edges of the tires experience wear. 2. Driving speed: Tire wear is also related to the vehicle's driving speed. The faster the driving speed, the more severe the tire wear. 3. Excessive tire pressure: Some vehicle owners, considering heavy loads or other reasons, inflate the tires to very high pressures.
Was this review help?
5
5
Share
VanAnnie
08/12/25 8:01am
Excessive tire wear is quite common among us experienced drivers, and I've seen plenty of it over my decade of driving. The main culprit is tire pressure – too high or too low both lead to uneven wear, especially the edges of front tires. Hard acceleration and sudden braking also accelerate wear, and every time I floor the gas pedal, I can practically hear my tires crying. Misaligned wheels are another issue – when the car pulls to one side, it can wear out tires in no time. Poor road conditions like frequent gravel or muddy roads will make treads disappear faster. My advice: use a tire pressure gauge monthly to maintain the manufacturer's recommended pressure, drive more gently, and your tires should last 30,000 km without trouble, saving you both money and hassle from frequent replacements.
Was this review help?
6
0
Share
Expand All
More Forum Discussions

Where is the OBD diagnostic connector for the BAIC M20?

The OBD diagnostic connector for the BAIC M20 is located below the blower on the passenger side. Here is some relevant information about the BAIC M20: 1. Interior space: The front row headroom is 830mm, the second row headroom is 1040mm, and the maximum legroom is 940mm; the third row headroom is 920mm, and the maximum legroom is 810mm. 2. Exterior design: The BAIC M20 features a mature, stable, and refined appearance with a strong German-style influence. It boasts a distinctive upper and lower fully sprayed titanium silver horizontal grille design and a bold front headlight design, along with daytime running lights.
19
5
Share

What is the Honda 240?

Honda 240 refers to the 240TURBO model of the Honda Avancier. Below are the relevant details about this vehicle: 1. Dimensions: The Avancier is a mid-size SUV under the Honda brand, with a wheelbase of 2820mm, and its length, width, and height are 4858mm, 1942mm, and 1670mm respectively. 2. Powertrain: The Avancier is equipped with two engines, one being a 1.5-liter turbocharged engine and the other a 2.0-liter turbocharged engine. The 1.5-liter turbocharged engine delivers a maximum power of 142kW and a maximum torque of 243Nm, with the maximum power achieved at 5600 rpm and the maximum torque available between 2000 to 5000 rpm.
12
4
Share

What does inline 4-cylinder mean?

Inline 4-cylinder refers to an engine configuration where four cylinders are arranged in a straight line. The inline-four engine is not a balanced structure. Although the imbalance is minimal in low-displacement, low-power configurations, vibrations increase as the engine size and power output grow. Some vehicles use V-type or W-type engines instead. A V-type engine has two banks of cylinders set at an angle to each other, while a W-type engine features four banks of cylinders also arranged at specific angles. The engine is often called the heart of a car as it provides the power needed to propel the vehicle. During operation, the engine goes through four strokes in continuous cycles: intake stroke, compression stroke, power stroke, and exhaust stroke.
9
5
Share

What are the measures to take when brake failure occurs?

Measures to take when brake failure occurs: After the brake system fails, you should downshift to use engine braking to slow down the vehicle. Do not use the handbrake, as this may directly cause the car to lose control. If you still cannot reduce speed, you can slow down by scraping against the roadside wall or railing. If you choose to do this, you must ensure the safety of other pedestrians and vehicles. The braking system is crucial for a car. It mainly consists of the vacuum booster, master cylinder, wheel cylinder, brake pads, and brake discs. When the driver presses the brake pedal, the vacuum booster provides assistance, helping the driver to press the pedal. After the driver presses the brake pedal, the master cylinder pushes the wheel cylinder through brake fluid, and the wheel cylinder then presses the brake pads against the brake discs.
12
1
Share

What are the symptoms of a stretched timing chain?

The symptoms of a stretched timing chain include: engine vibration and incorrect ignition timing. The reasons for timing chain elongation: The timing chain is made of metal, unlike the timing belt which is a rubber component. Under high-temperature operation, the engine's thermal expansion and contraction cause metal fatigue in the timing chain, leading to loosening over time and resulting in a certain degree of elongation. The timing chain is composed of pins, chain plates, sleeves, and rollers. The rollers experience the most friction among the chain components. Poor-quality chains wear out quickly during use, while high-quality ones delay wear but still reach a certain limit. As the rollers become thinner, the wheelbase correspondingly lengthens.
8
3
Share

Where is the auto start-stop switch for BMW Mini?

The auto start-stop switch for BMW Mini is located below the one-touch start button. Here is the relevant introduction to the BMW Mini Black Label: 1. Exterior: The Black Label MINI special edition features darkened treatments on the emblem, side scuttles, front and rear light clusters, waistline, wheels, and interior details. 2. Powertrain: The model offers four powertrain versions: ONE, COOPER, COOPER-S, and JCW, corresponding to a 102-horsepower 1.5T engine, a 136-horsepower 1.5T engine, a 192-horsepower 2.0T engine, and a 231-horsepower 2.0T engine, respectively.
8
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.