What Causes Tire Vibration at Idle?

1 Answers
OCaroline
07/30/25 6:40am
Minor tire vibration at idle is normal. Below is additional information: Introduction to Idle Vibration: Idle vibration occurs when the engine is running but the oil supply doesn't keep up promptly, resulting in poor mechanical operating conditions for the engine or issues like poor fuel injector atomization and improper idle adjustment, which cause engine vibration. If noticeable body vibration occurs when starting the vehicle or when the vehicle is stationary with the engine running, it is usually due to severe engine carbon buildup or a dirty throttle body. When there's excessive carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, leading to an overly lean air-fuel mixture during cold starts and making it difficult to start. In this situation, the engine will only start easily once the carbon deposits are saturated with gasoline. After starting, the gasoline adsorbed on the carbon deposits is drawn into the combustion chamber by the engine's vacuum, enriching the air-fuel mixture again. This fluctuation between lean and rich mixtures causes idle vibration after a cold start. Solutions for Idle Vibration: If the car body vibrates when stationary in N gear, with noticeable seat and steering wheel vibrations, and the vibration is obvious while driving, but the engine power is normal and no engine fault indicator is lit on the dashboard, this is mostly caused by aging, cracking, or oil leakage in the engine mounts. You can check the engine mounts for faults and replace them if necessary.
Was this review help?
16
4
Share
More Forum Discussions

How to Observe the Battery Level of an Electric Vehicle?

To check the battery level of a car, observe the feedback when starting the engine. If starting feels particularly difficult, it indicates that the battery is running low. Additionally, the battery warning light, if constantly lit, signifies that the car battery is about to run out of power and requires immediate charging. Below are some relevant details about car battery charging: 1. Decoding Definition: The car cannot be completely powered off, so when using a charger, connect it directly to the battery for charging without removing the battery. Otherwise, data loss may occur, necessitating initialization. 2. Precautions: If the battery voltage is 10% lower than the rated voltage, there is a risk of the battery running low. It is recommended to fully charge the battery at least once a month.
17
4
Share

What is the Difference Between Transverse and Longitudinal Engine Layouts?

Transverse and longitudinal engine layouts differ specifically in terms of the placement direction of the engine and transmission, the direction of power output, the vehicle's drive system, and the suspension system. Normally, car engines are placed in the front engine compartment. If the engine crankshaft axis is aligned in the same direction as the wheel half-shaft axis, it is a transverse layout. If the engine crankshaft axis is arranged perpendicular to the wheel half-shaft axis, it is a longitudinal layout. Placement direction of engine and transmission: A transverse engine is placed horizontally, requiring the transmission to be placed horizontally alongside it. A longitudinal engine is placed vertically, with the transmission positioned behind the engine. Direction of power output: The power transmission direction of a transverse engine is typically perpendicular to the vehicle's forward motion. After entering the transmission, the power is usually transmitted laterally directly to the half-shaft. The power transmission direction of a longitudinal engine is parallel to the vehicle's forward motion, transmitting backward. After entering the transmission, the power continues to be transmitted longitudinally backward, often connecting to an intermediate drive shaft for direct rearward transmission. Vehicle drive system: Transverse engines are typically used in front-wheel-drive vehicles, while longitudinal engines are commonly found in rear-wheel-drive vehicles. Suspension system: Vehicles with a longitudinal engine layout require less horizontal space, allowing for more room to install advanced multi-link or double-wishbone suspension systems. In contrast, transverse engine layouts, due to the longer engine length and the need to place the transmission alongside, demand more horizontal space. As a result, transverse engine layouts often use the more economical MacPherson strut suspension for the front suspension.
1
3
Share

Does the Geely Jiaji have a 4-cylinder engine?

Geely Jiaji has a 4-cylinder model, which is equipped with a 1.8t engine, while the 1.5t engine model is a 3-cylinder engine. The relevant introduction of the 4-cylinder engine is as follows: Working principle of the 4-cylinder engine: It usually converts chemical energy into mechanical energy. Sometimes the engine is not only applicable to the power generation device, but also refers to the entire machine including the power device, such as gasoline engines and aircraft engines. The main part of the engine is the cylinder, which is the power source of the entire car. Purpose of the 4-cylinder engine: The 4-cylinder engine body is mainly composed of cylinder block, crankcase, cylinder head and cylinder gasket. Main uses: mostly used in car engines, motorcycles, chainsaws and other small power machinery.
20
4
Share

What are the reversing techniques?

Here is an introduction to reversing techniques: 1. Adjust the position between the car body and the corner of the garage: When reversing for the first time, lean forward to check the right rearview mirror in advance to observe the positional relationship between the car body and the corner of the garage. Predict whether the car body will be too close or too far from the corner of the garage based on the angle observed in the rearview mirror, then steer to correct it. It is best to maintain a distance of 30 centimeters between the car body and the corner of the garage. 2. Correct the car body inside the garage: After the rear half of the car body enters the garage, steer to adjust. Observe the left and right rearview mirrors to determine which side the front of the car is leaning towards and which side the rear is leaning towards, then steer towards the side the front is leaning to correct the car body. 3. Find the right stopping point: Judge when to stop by observing the relationship between the left rearview mirror and the side line. When the left rearview mirror covers the side line, immediately press the clutch to stop.
13
2
Share

What are the differences between medium-sized buses and large buses?

The differences between medium-sized buses and large buses are as follows: 1. Passenger capacity: Vehicles with a seating capacity of more than 9 but fewer than 20 people are classified as medium-sized passenger vehicles; those with a certified capacity of more than 19 people are classified as large buses. 2. Driver's license level: A Class A1 license is required to drive large buses; according to the 'Regulations on the Application and Use of Motor Vehicle Driving Licenses,' drivers holding a Class B1 license are permitted to operate medium-sized passenger vehicles. 3. Vehicle length: Vehicles shorter than 6 meters are classified as medium-sized passenger vehicles; large urban buses (10-12 meters) and extra-large urban buses (articulated buses are 13-18 meters, double-decker buses are 10-12 meters with two levels of seating).
7
2
Share

How Many Kilometers Should a Volvo Timing Belt Be Replaced?

Volvo timing belts should be replaced between 90,000 to 100,000 kilometers. Below is relevant information about the function of timing belts: 1. Driving the Valve Train: It drives the engine's valve train. Even those with shorter usage periods should not exceed 100,000 kilometers. When replacing, use genuine or major brand products and opt for complete sets to ensure performance. During replacement, strictly adhere to the torque parameters of each component to meet the original factory specifications. The generator and compressor belts can be replaced at the same time. 2. Opening and Closing Exhaust Valves: It ensures the engine's intake and exhaust valves open and close at the appropriate times. 3. Enabling Normal Cylinder Intake and Exhaust: It guarantees that the engine cylinders can intake and exhaust air normally.
9
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.