What Causes Tire Bulging?

2 Answers
OAshlyn
07/24/25 7:04am
Tire bulging is caused by: 1. Driving over potholes at high speed; 2. Quickly running over protruding obstacles; 3. Mounting curbs at a small angle; 4. Quality issues with the tire itself. Tires are crucial components of a vehicle, and their functions include: 1. Supporting the entire weight of the vehicle, bearing the load, and transmitting forces and moments in other directions; 2. Transmitting traction and braking torque to ensure good adhesion between the wheels and the road surface; 3. Improving the vehicle's power, braking, and off-road capabilities, working with the suspension to mitigate impacts during driving and dampen resulting vibrations; 4. Protecting vehicle components from severe vibrations and premature damage; 5. Adapting to high-speed performance and reducing driving noise; 6. Ensuring driving safety, handling stability, comfort, and fuel efficiency.
Was this review help?
15
2
Share
VanElle
08/11/25 2:49am
I've been driving for almost ten years, and tire bulges are really not uncommon. The most common cause is accidentally hitting potholes or curbs while driving—the sudden impact is too strong, causing the inner cord layers of the tire to tear or separate, resulting in a bulge on the sidewall. Tire pressure is also crucial; too high or too low is bad. Low pressure means insufficient sidewall support, making it prone to deformation when hitting obstacles, while high pressure reduces elasticity and can also cause bulges. Another issue is tire aging—after four or five years, the rubber becomes brittle, and hot weather accelerates this process, weakening the tire and making it more prone to problems. When driving, pay attention to the road surface, slow down when encountering bumps, and avoid overloading the car to reduce tire stress. Check the tire pressure monthly to maintain the standard level. If you notice a bulge, don’t take chances—replace the tire immediately, as a high-speed blowout is extremely dangerous.
Was this review help?
11
4
Share
Expand All
More Forum Discussions

What is the equivalent car displacement for a 300cc motorcycle?

300CC on a motorcycle is equivalent to 0.3L displacement in a car. Below is relevant information about displacement: Definition of Displacement: A specialized term in hydraulic transmission, referring to the volume of fluid inhaled or discharged per stroke or cycle. Displacement Classification: In China, car classification is determined by displacement size. Mini cars have a displacement ≤1.0L; compact cars range between 1.0–1.6L; midsize cars range between 1.6–2.5L; executive cars range between 2.5–4.0L; and luxury cars have a displacement >4.0L.
11
2
Share

What height is suitable for a motorcycle with a 790mm seat height?

Although the 790mm seat height of the motorcycle is relatively high for general motorcycles, a height of 1.85 meters is also quite tall, so riding a motorcycle with this 790mm seat height poses no problem. Relevant information about motorcycles is as follows: Introduction: Motorcycles are powered by gasoline engines and are two-wheeled or three-wheeled vehicles steered by handlebars to control the front wheel. They are lightweight, flexible, and fast, widely used for patrol, passenger and cargo transportation, and also serve as sports equipment. Classification: Motorcycles are divided into street bikes, road racing motorcycles, off-road motorcycles, cruisers, touring bikes, etc.
2
2
Share

At what percentage of oil life does a Cadillac require maintenance?

Oil should be changed when its remaining life reaches 10% or 20%. The oil change intervals for Cadillac are as follows: Mineral oil change: The replacement cycle for mineral oil is every six months or 5,000 kilometers. This helps reduce wear on engine components, not only extending their service life but also decreasing the vehicle's fuel consumption. Semi-synthetic oil change: The replacement cycle for semi-synthetic oil is every six months or 7,500 kilometers. After changing to semi-synthetic oil, pay attention to the vehicle's fuel consumption maintenance. Avoid suddenly switching oil types to prevent potential vehicle malfunctions.
19
2
Share

What does a hammer drill with clutch mean?

A hammer drill with clutch refers to a hammer drill equipped with a safety clutch. When encountering rebar or overload, the drill bit stops outputting to ensure personal safety and prevent motor stalling and burning. Below is a detailed introduction to the working principle of a hammer drill: The working principle of a hammer drill is that while the transmission mechanism drives the drill bit to rotate, it also generates a reciprocating hammering motion perpendicular to the direction of the drill bit. The hammer drill operates by the transmission mechanism driving a piston to reciprocate and compress air within a cylinder. The periodic changes in air pressure inside the cylinder drive the hammer inside the cylinder to reciprocate and strike the top of the drill bit, hence the name hammer drill.
11
4
Share

What Causes Motorcycle Steering to Be Less Flexible?

When riding a motorcycle, the rider may feel that the handlebars are difficult to turn or that the steering is alternately tight and loose. The reasons for this lack of steering flexibility include the following: Insufficient front tire pressure: Low tire pressure increases friction between the tire and the ground, making steering more strenuous for the rider. Over-tightened steering stem adjustment nut: If the steering stem adjustment nut is too tight, it reduces the clearance between the steering stem ball bearings and their races, leading to difficult and inflexible steering, as well as accelerated wear of the ball bearings and races. Excessive wear or damage to the steering stem ball bearings or races. Bent or deformed steering stem.
16
5
Share

Is the Volkswagen Lavida transmission failure normal?

Volkswagen Lavida transmission failure is not normal and requires timely repair. The following is a detailed introduction about car transmissions: 1. Overview: The transmission is a device that changes the speed ratio and direction of movement, usually located between the clutch and the central drive. It can change the torque, speed, and direction of movement transmitted from the driving shaft to the driven shaft according to different working conditions. Gear-driven transmissions generally consist of a housing and several gears. 2. Classification: Automatic transmissions have become mainstream internationally, mainly including AT, AMT, CVT, and DCT types. The early transmission system of AT transmissions was mainly 4AT. AT achieves automatic shifting through an electronically controlled automatic operating system. CVT is a true continuously variable transmission with fewer parts and a smaller size. DCT has two clutches.
17
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.