What Causes the Xiali Fuel Injector Not to Spray Fuel?

2 Answers
SanEverly
07/29/25 6:32am
Xiali fuel injector not spraying fuel can be caused by insufficient fuel, damaged fuel pump, high-pressure fuel pump failure, etc. The relevant introduction of the fuel injector is as follows: Definition of Fuel Injector: The fuel injector used in modern cars is essentially a simple solenoid valve. When the solenoid coil is energized, it generates suction, lifting the needle valve to open the injection hole. Fuel is sprayed at high speed through the annular gap between the needle valve head and the injection hole, forming a mist that facilitates complete combustion. Working Principle of Fuel Injector: The fuel injector itself is a normally closed valve (a normally closed valve means that the valve remains closed when there is no input control signal; whereas a normally open valve remains open when there is no input control signal), with the opening and closing controlled by the up and down movement of a valve needle.
Was this review help?
12
1
Share
MacFinn
08/12/25 9:57am
Having worked on cars for many years, I've encountered quite a few cases where the Xiali's fuel injectors fail to spray fuel. There are numerous possible causes: the most common is a faulty fuel pump failing to supply adequate fuel pressure; a clogged fuel filter can also cut off fuel supply; carbon buildup causing the injector to stick or wear out—low-quality gasoline is the usual culprit here; electrical issues like blown fuses—older cars like the Xiali suffer from rapid wiring degradation, so the fuse box needs regular checks; a malfunctioning control unit or faulty crankshaft position sensor can lead to signal errors, preventing fuel injection commands from being sent; unstable battery voltage affecting power supply is another factor. For diagnosis, start by listening for the fuel pump's operation, check if any fuses are blown, and try replacing them with new ones; regular maintenance is key to prevention—using quality fuel and cleaning the injectors can extend their lifespan. If the car truly won't start due to this issue, seek professional repair immediately—don't tinker randomly and risk damaging the chassis.
Was this review help?
6
5
Share
Expand All
More Forum Discussions

Is the 2019 Sylphy compliant with China 6 emission standards?

The 2019 Sylphy was launched in September 2018 and meets the China 6 emission standards. Below is an introduction to the 2019 Nissan Sylphy: 1. The new car has almost no changes in appearance and dimensions, featuring a three-horizontal-bar shield-shaped front grille, with lines on both sides of the engine hood extending towards the center, giving the overall design a sense of strength. 2. The new car is equipped with practical configurations such as ABS, EBD, an onboard computer display, and a brake assist system. It adopts a front MacPherson strut independent suspension and a rear torsion beam suspension. 3. The 2019 Sylphy is powered by a 1.6L naturally aspirated engine with a maximum power of 93kW and maximum torque of 154Nm, and a 1.8L naturally aspirated engine with a maximum power of 102kW and maximum torque of 174Nm.
2
0
Share

What is the emission standard of the Classic Focus?

The emission standard of the Classic Focus is China IV. Here are the relevant details: 1. China IV is the national fourth-stage motor vehicle pollutant emission standard. The main pollutants emitted by vehicles include HC, NOx, CO, PM, etc. By applying technologies such as improved catalytic converter active layers, secondary air injection, and exhaust gas recirculation systems with cooling devices, the standard controls and reduces vehicle emissions to below specified levels. 2. The Classic Focus is a compact car under Changan Ford, with exterior dimensions of 4647mm in length, 1810mm in width, and 1468mm in height, a wheelbase of 2705mm, and a body structure of a 4-door, 5-seater sedan.
3
4
Share

How to Deal with Hard Braking?

Here are the methods to handle hard braking in cars: 1. When braking, users should try to minimize the braking distance to protect the brake pads. First, use the engine's braking effect by downshifting to reduce speed, then lightly press the brake pedal. This shortens the braking distance and reduces wear on the brake pads. 2. Pay special attention to maintaining a safe distance during daily driving, decelerate in advance, and avoid sudden braking. Especially when the traffic light at an intersection is flashing, do not force your way through. 3. During normal driving, if you are not using the brakes, your foot should be off the brake pedal. Even resting it lightly on the pedal is not advisable, as it can easily increase wear on the brake pads. It is important to develop the habit of immediately releasing the pedal and lifting your foot after braking.
16
3
Share

How often should the spark plugs of Baojun 560 be replaced?

Baojun 560 spark plug replacement cycle: Under normal maintenance conditions, they should be replaced after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the user manual. You can refer to the following standards for maintenance replacement: Platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. How spark plugs work: The ground electrode of the spark plug is connected to the metal shell, which is threaded into the engine block via the cylinder head. The insulator primarily serves to isolate the metal shell from the center electrode. The terminal nut is the part of the spark plug that contacts the high-voltage coil. When current passes through the terminal nut and the center electrode, it ionizes the medium between the center electrode and the ground electrode, generating a spark to ignite the air-fuel mixture in the cylinder.
18
3
Share

What gear should an automatic car be in when parked on a slope?

Automatic cars parked on a slope can be placed in the following two gears: 1. D gear: Since some automatic cars come with hill-start assist, when in D gear, you need to master the throttle and coordinate with the brake to achieve a smooth start on a steep slope. 2. On steep slopes, it is recommended to use manual mode, specifically the S+ gear in the S mode. This gear is the lowest in manual mode, offering the highest torque and force, and when coordinated with the brake, it can complete the hill start. Here is some relevant information about automatic cars: 1. Most automatic cars have P gear (Park), R gear (Reverse), N gear (Neutral), and D gear (Drive). It is important to use the automatic transmission properly to save fuel more efficiently. 2. When using D gear to climb a slope, if pressing the accelerator does not provide the same power as on flat roads, you should immediately switch to a low-speed gear with high torque. This not only saves fuel but also reduces engine wear. When encountering an uphill on city roads, avoid suddenly accelerating. Instead, accelerate before the uphill to increase speed.
7
2
Share

What are the issues if a gasoline car is filled with diesel engine oil?

Filling a gasoline car with diesel or diesel engine oil can cause difficulties in starting the vehicle. During driving, the exhaust pipe may emit smoke, and there is a high likelihood of damage to the catalytic converter. Below is an introduction to the related content: Although both gasoline and diesel engines are internal combustion engines, diesel has a lower auto-ignition point, around 220°, whereas gasoline has a much higher ignition point, between 410° and 430°. Therefore, diesel engines use compression ignition and do not require spark plugs for ignition. They rely on compressing air to raise the temperature to the diesel's ignition point, then inject diesel, which auto-ignites. Consequently, if diesel enters a gasoline engine, it will start burning violently on its own before the spark plug ignites, causing abnormal pressure in the combustion chamber, commonly known as knocking. This will also be accompanied by other engine abnormalities. Once it is discovered that the issue is caused by mistakenly adding diesel, it is crucial to stop attempting to start the engine to prevent diesel from entering the fuel system. Then, take the car to a 4S shop or repair shop to drain the diesel completely and refill it with gasoline.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.