What Causes the Trunk Speaker of Tango to Stop Working?

How to reset the SET light?

Users can only drive the car to a 4S shop and have the staff use a computer to clear the fault light. When the engine fault light is on, the SET fault light cannot be manually reset. It usually requires using a fault diagnostic tool at a 4S shop for troubleshooting before it can be cleared. Additional information: Understanding car indicator lights: 1. Oil pressure fault light: Indicates that the oil level and pressure are below the standard value. Continuing to drive may cause the engine to lose lubrication, leading to severe wear. If the fault light remains after adding oil, do not start the vehicle and contact rescue services as soon as possible. 2. Coolant temperature warning light: Displays the temperature of the coolant in the vehicle's engine. Some models without a coolant temperature gauge (such as Great Wall compact car series) use the color of the indicator light to show the coolant temperature: blue indicates the coolant temperature is too low, and the light turning off indicates the temperature is normal. 3. Brake system fault light: If the brake system fault light comes on, first check if the handbrake is fully released. If the light remains on after releasing the handbrake, check if the brake fluid level is normal or if the brake pads are too thin. If the braking force is not weakened, you can drive cautiously and go to the nearest repair shop as soon as possible.

19

1

Share

Is It Normal for Black Smoke to Appear When Accelerating Hard?

The phenomenon of black smoke appearing when accelerating hard is not normal. The essence of black smoke is incomplete combustion, and the reasons for incomplete combustion are as follows: 1. Air intake issues: The most common cause is a clogged or contaminated air filter. The first step in diagnosing this problem is often to check the air filter. 2. Poor air supply due to system wear: This issue requires a 4S inspection to determine the root cause. Worn turbochargers, clogged air filters, and poor driving habits leading to malfunctioning solenoid valves and inadequate lubrication may be the reasons for poor air supply. 3. Poor fuel supply: Due to substandard fuel quality, its viscosity and ash content (impurity levels) are too high, causing wear, clogging, and carbon buildup in the fuel injector solenoid valves, affecting their sealing performance. This ultimately results in an abnormal air-fuel mixture ratio, incomplete combustion, and the production of black smoke. Common causes of poor fuel supply also include clogged fuel systems due to dust and particulate matter. 4. Malfunctioning solenoid valves: Dust and particulate matter in the air can damage solenoid valves, leading to insufficient turbocharging, reduced air density, and incomplete combustion.

3

5

Share

What does GL8ES mean?

GL8-ES series models are the new generation vehicles with a brand-new exterior design and more innovative interior styling, equipped with a 2.0T engine and rear multi-link independent suspension. Below are the key details about GL8-ES: 1. The GL8-ES comes standard with features such as tire pressure monitoring, remote start, keyless ignition system, cruise control, rear radar, engine start-stop, hill start assist, auto hold, hill descent control, multifunction steering wheel, paddle shifters, front and rear seat + backrest adjustment, in-cabin PM2.5 filter, daytime running lights, UV/heat-insulating glass, CarPlay support, and more. Based on these, even the entry-level GL8-ES configuration can largely meet user needs. 2. Among the four GL8-ES variants, active safety features like lane departure warning, lane keeping assist, and blind-spot monitoring are only available on the top-tier model. The pricing for the four new GL8-ES variants remains unchanged, and they comply with the China VI emission standards.

15

1

Share

What is the principle of the fuel tank float and what are the manifestations of its faults?

The working principle of the fuel float is: 1. The fuel float floats on the surface of the fuel by buoyancy, and the position of the float indicates the liquid level. By knowing the height of the liquid level and the shape of the fuel tank, the volume of fuel inside the tank can be determined; 2. It acts as a sliding resistor. Different fuel levels result in different positions of the float, which in turn changes the resistance of the sliding resistor connected to the float. The computer supplies a voltage to the sliding resistor, and after measuring the voltage drop, it estimates the fuel level and displays the data on the car's dashboard; 3. The actual float in the fuel tank is a sliding variable resistor. The movement of the float changes the resistance in the circuit, which is then reflected by the fuel gauge needle on the dashboard. The following are the manifestations and solutions for fuel float faults: 1. The fuel gauge suddenly drops to zero. This indicates an issue with the vehicle's fuel level sensor, commonly known as the fuel float. The cause is usually dirt or contamination on the sensor that hasn't been cleaned in time; the solution is to clean the fuel level sensor. 2. If the gasoline contains a large amount of impurities, the fuel level sensor inside the tank, being submerged in the fuel, can become contaminated over time, directly affecting the accuracy of the readings. The solution is to clean or replace the fuel float.

19

4

Share

Should the Kia K3 use 92 or 95 octane gasoline?

According to the official vehicle manual recommendation, the Kia K3 should use 92 octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle manual, the Kia K3's recommended fuel type can also be found on the fuel tank cap, which will be clearly marked. Typically, the fuel grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of new technologies, the compression ratio alone cannot determine the required gasoline grade, as high compression ratio engines can also be tuned to use lower octane fuel. Other factors, such as ignition timing, turbocharging technology, and Atkinson cycle technology, also play a role. Generally, the higher the gasoline octane number, the higher the octane rating and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Kia K3 occasionally uses the wrong gasoline grade, simply switch back to the correct grade after the current tank is used up. However, prolonged use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower octane fuel, using higher octane gasoline will not cause damage, but the increased octane rating alters the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended to use higher octane fuel, using lower octane gasoline can cause engine knocking. The significantly lower octane rating reduces the fuel's ignition point, causing premature ignition during the compression stroke. If combustion occurs before the spark plug ignites, resistance will be encountered during the upward stroke. This resistance makes the engine run very unstably. Mild knocking may only increase noise without obvious engine damage, but severe knocking indicates serious engine conditions. The vibrations not only affect driving stability but can also cause abnormal wear to the piston and cylinder, and in severe cases, lead to cylinder scoring.

14

0

Share

How to Remove the Spare Tire of a Ford Edge?

The spare tire of the Ford Edge is located under the trunk cover. Simply open the trunk cover and take it out. Precautions for using the spare tire are as follows: 1. Regularly inspect the spare tire. During routine maintenance or before long-distance trips, few car owners check the spare tire, and some unprofessional repair shops often overlook this. Spare tire inspection mainly involves checking tire pressure, wear, and cracks. Replace the tire as soon as possible if the tread wears down to the wear indicator line. If there are fine cracks on the tire sidewall, avoid using it for long-distance or high-speed driving, as the sidewall is thinner and prone to blowouts at high speeds. 2. Do not store oil products with the spare tire. The main component of tires is rubber, which is most vulnerable to erosion by various oil products. Car owners often store lubricants and other oil products in the trunk. If these oils come into contact with the tire, they can cause swelling and corrosion, significantly reducing the tire's lifespan. If the tire gets contaminated with oil, promptly wash it off with a neutral detergent. 3. The lifespan of a spare tire is about 4 years. Since tires are rubber products, prolonged storage can lead to aging. Generally, the aging period for tires is about 4 years, so the spare tire should be replaced after this period.

16

4

Share

What Causes the Trunk Speaker of Tango to Stop Working?

How to reset the SET light?

Is It Normal for Black Smoke to Appear When Accelerating Hard?

What does GL8ES mean?

What is the principle of the fuel tank float and what are the manifestations of its faults?

Should the Kia K3 use 92 or 95 octane gasoline?

How to Remove the Spare Tire of a Ford Edge?

What is the displacement of the Toyota Levin?

How to reset the maintenance light on the 2015 Chery E3?

What to Do When 12 Points Are Deducted from a C1 Driver's License?

Why does the Magotan's fan keep running after the engine is turned off?