What Causes the Tire Pressure Light to Illuminate?

2 Answers
SanManuel
07/24/25 8:29pm
The reasons for the tire pressure light to illuminate: 1. The tire pressure monitoring light may come on due to a punctured tire; 2. Sometimes the tire pressure monitoring light illuminates because the tire pressure is too high; 3. Driving for an extended period with low tire pressure can trigger the tire pressure monitoring light; 4. The tire pressure monitoring light may also come on if the tire pressure has dropped due to prolonged lack of inflation. When the tire pressure system alerts, first pull over safely and check the tire pressure of all four tires. If no obvious loss of air is visible, you can ignore it. After getting back in the car, reset the tire pressure system to turn off the warning light. Continue driving for a while. If the tire pressure warning light comes on again, it indicates that there is indeed a problem with the tire pressure of one of the tires, and it needs to be checked and repaired promptly.
Was this review help?
9
1
Share
LeLevi
08/11/25 11:11am
When the tire pressure warning light comes on, it usually means your car is alerting you that the tire pressure may be below the normal value. This is often caused by a tire leak, such as a punctured nail or slow leak. A sudden drop in temperature can also cause the pressure to decrease, leading to a false alarm. If the light remains on despite normal pressure, the TPMS sensor may be malfunctioning, such as due to a drained battery or signal interference. My first recommendation is to pull over and check all tires with a simple tire pressure gauge, comparing the readings to the recommended values on the door frame. If the pressure is too low, inflate the tires to the proper level, and the light should turn off. If the issue persists, it's best to take the car to a repair shop and have a technician use professional tools to test the sensor circuit. Ignoring it is not an option—long-term low tire pressure can wear out the tire edges, increase fuel consumption by a few percent, and even lead to blowouts at high speeds, posing a safety risk. Therefore, timely action is crucial.
Was this review help?
7
2
Share
Expand All
More Forum Discussions

How to Diagnose Automotive Circuit Faults?

Common troubleshooting methods for automotive circuit faults: Common automotive circuit faults mainly include: open circuits, short circuits, electrical equipment damage, etc. To quickly and accurately diagnose faults, here are several common maintenance methods. Visual diagnosis method: When an automotive circuit malfunctions, sometimes abnormal phenomena such as smoke, sparks, abnormal sounds, burnt smells, or overheating may occur. These phenomena can be directly observed to determine the fault location. Short circuit method: When an automotive circuit device experiences a grounding (short circuit) fault, the open circuit method can be used for judgment. That is, after disconnecting the suspected faulty circuit section, observe whether the grounding fault still exists in the electrical equipment, thereby determining the location and cause of the circuit grounding. Open circuit method: If an open circuit fault exists in the automotive circuit, the short circuit method can also be used for judgment. That is, use a screwdriver or wire to short-circuit the suspected open circuit fault section, and observe changes in the instrument pointer or the operation of the electrical equipment to determine if an open circuit fault exists. Test lamp method: The test lamp method uses an automotive bulb as a test lamp to check if an open circuit fault exists in the circuit. Instrument method: Observe the indications of the ammeter, water temperature gauge, fuel gauge, oil pressure gauge, etc. on the automotive dashboard to determine if there is a circuit fault. For example, when the engine is cold and the ignition switch is turned on, if the water temperature gauge indicates full scale without movement, it indicates a fault in the water temperature sensor or a grounding in the circuit.
8
1
Share

What Are the Basic Methods of Automotive Diagnosis?

Basic methods of automotive fault diagnosis: Inquire with the user about the time, symptoms, and circumstances when the fault occurred, the possible causes, and whether any repairs or disassembly have been performed. Initially determine the scope and location of the fault. Retrieve the fault code and identify the content of the fault. Based on the fault range indicated by the fault code, conduct repairs, paying special attention to whether connectors are loose or detached and whether wire connections are correct. After completing the repairs, verify whether the fault has indeed been resolved. If the fault code cannot be retrieved or if the fault content cannot be identified after retrieval, roughly determine the fault range based on the symptoms and use a method of checking the working performance of each component one by one to eliminate the fault. Currently, there are basically two diagnostic methods for automotive faults: one is the manual intuitive experience diagnostic method, and the other is the instrument and equipment diagnostic method. The instrument and equipment diagnostic method involves obtaining performance and fault information parameters of the vehicle without disassembling the assembly, comparing them with the technical condition of a normal vehicle, and providing conclusions on technical performance and faults. With the application of electronic information and computer technology in automobiles, diagnostic instruments and equipment for automotive faults are becoming increasingly sophisticated, and more advanced instruments are being used in automotive fault diagnosis. Instruments and equipment enable fast and highly accurate fault diagnosis, can detect latent faults, and can also predict the service life of assembly components.
11
0
Share

What are the requirements for a Tesla test drive?

There are no special requirements; a driver's license is sufficient. Below is relevant information about the Model 3: 1. Introduction to the Model 3: The Tesla Model 3 is a new product in the Tesla Model X series, officially released in the United States on April 1, 2016, at 11:30 AM Beijing time. 2. Features: The Model 3 does not use an aluminum body, so the body size will be reduced by 20% to offset the impact of increased weight on range. The Model 3 is expected to have a range of approximately 320 kilometers. It eliminates the ultra-cool but impractical falcon-wing doors and the 3-second 0 to 60 mph acceleration, and may also remove the autopilot feature.
16
2
Share

How to Distinguish Between 4WD and 2WD Highlander by Appearance?

There is an AWD badge on the rear exterior, and the cabin features a hill descent control function. Below is relevant information about the Highlander: 1. Introduction to the Highlander: The Highlander is a vehicle produced by Toyota, a large-sized SUV in the Toyota family. It boasts a spacious body and innovative, roomy interior. Moreover, the Highlander comes equipped with safety features that meet the highest standards in its class. 2. Features of the Highlander: This SUV offers an exceptionally quiet ride and outstanding responsiveness, combining versatility with driving comfort. It is powered by a 3.5-liter V6 engine delivering up to 201 kW of output, paired with a stepped 5-speed automatic transmission with manual mode, ensuring smooth acceleration and excellent fuel economy.
1
3
Share

What is the battery capacity of Tesla?

Tesla cars have a battery capacity ranging from 55kWh to 90kWh. Below is relevant information about the Model 3: 1. Introduction to the Model 3: The Tesla Model 3 is a new product in the Tesla Model X series, unveiled in the United States at 11:30 AM Beijing Time on April 1, 2016. 2. Features: The Model 3 does not use an aluminum body, so the body size will be reduced by 20% to offset the impact of increased weight on range. The Model 3 is expected to have a range of approximately 320 kilometers. It eliminates the super cool but impractical falcon-wing doors, removes the 3-second acceleration from 0 to 60 mph, and may also remove the autopilot feature.
14
2
Share

What are the reasons for the high fuel consumption of the 12th-generation Crown?

The reasons for the high fuel consumption of the 12th-generation Crown are as follows: Affected by temperature: This leads to fluctuations in fuel consumption. In winter, when temperatures are low, fuel consumption tends to increase. Vehicle not maintained for a long time: Dirty engine oil and air filters can also lead to increased fuel consumption. Dirty engine oil causes poor lubrication, increasing resistance in the engine's moving parts, requiring more energy to overcome the resistance, thus raising fuel consumption. Insufficient tire pressure: Low tire pressure increases the contact area between the tires and the ground, increasing friction and thus driving resistance, which leads to higher fuel consumption. Excessive carbon buildup in the vehicle: Carbon buildup can occur in the throttle body, fuel injectors, intake manifold, and piston tops. Excessive carbon buildup in any of these areas can lead to incomplete combustion, resulting in increased fuel consumption.
10
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.