What Causes the Steering Wheel to Shake Left and Right on Its Own?

1 Answers
OAustin
07/24/25 8:39pm
Experiencing steering wheel vibration while driving is quite common. Some drivers may feel intense steering wheel shaking when driving at high speeds. This condition is mostly caused by issues with the car tires. When the mass distribution of the tire is uneven, it creates a dynamic imbalance when the wheel rotates at high speed, leading to severe steering wheel vibration during driving. More relevant information is as follows: 1. Apart from tire-related issues, potential causes could include shock absorber failure, frame deformation, or excessive clearance in the meshing of the main and driven gears of the final drive. If the steering wheel shakes during braking while driving, it might be due to excessive or frequent braking, which can cause the brake discs and pads to overheat and deform when cooled, resulting in steering wheel vibration. 2. Generally, replacing the brake discs and pads can resolve this symptom. If the steering wheel shakes at lower speeds, it could be due to a loose belt in the mechanical steering system's steering gear causing slippage, which also leads to steering wheel vibration. Additionally, looseness or excessive clearance in the steering linkage system can cause vibration and abnormal noises, though this is relatively rare.
Was this review help?
14
0
Share
More Forum Discussions

Why Can't the Car Trunk Close?

The reasons why the car trunk cannot close are: 1. The automatic lift switch uses an overly stiff spring rod; 2. The closing limit rubber block does not match the locking mechanism properly; 3. The trunk control circuit is faulty; 4. The trunk hydraulic support rod is faulty. The methods to open the car trunk are: 1. Open the car door, firmly pull up the button below the handle, and then push the trunk upward; 2. Press the one-touch trunk opening button in the middle of the car key and hold it for about three seconds to open the trunk. The car trunk is a space for storing spare items and carrying goods, including: 1. The car's spare tire; 2. The vehicle's first aid kit; 3. The onboard tool kit; 4. The triangle warning sign; 5. The fire extinguisher; 6. The car refrigerator; 7. The emergency fuel tank cap release cable.
5
3
Share

How to Shift Gears in a Tiptronic Transmission?

The method for shifting gears in a tiptronic transmission is: While driving, release the accelerator, shift the gear lever to the M position. When switching to M mode, there's no need to press the brake or release the accelerator. In M mode, you can shift up or down by moving the gear lever back and forth. The gear operations for a tiptronic transmission are: 1. D is the drive mode, used for normal road driving; 2. R is the reverse gear, which can only be engaged after the car has come to a complete stop; 3. P is the parking gear, to be used when the vehicle is stationary and should be accompanied by engaging the handbrake; 4. L is the low gear, providing greater power output; 5. N is the neutral gear, used when the car is temporarily stopped; 6. W is the winter/snow mode, suitable for driving on slippery or snowy surfaces.
13
1
Share

What are the three major components of the Yixuan?

Yixuan's three major components are the engine, chassis, and transmission. Engine: The Yixuan is equipped with a Dynamic-Force series engine, specifically the M20A 2.0L naturally aspirated engine, delivering a maximum power of 126kW, maximum horsepower of 171Ps, and peak torque of 203Nm. Chassis: The Toyota Yixuan's chassis is built on the TNGA architecture, with overall tuning leaning towards comfort, easily filtering out general bumps. The suspension setup also favors comfort, featuring MacPherson front suspension and a double-wishbone rear suspension with trailing arms, providing ample support during turns to maintain vehicle stability. Transmission: The Toyota Yixuan utilizes a CVT (Continuously Variable Transmission), which efficiently transfers kinetic energy and boasts the industry's widest gear ratio range for direct shifting. It also reduces the load and wear on the steel belt, further enhancing dynamic response.
3
4
Share

Why does the MG ZS make a noise when turning the steering wheel?

There is an abnormal noise in the steering wheel, which is likely the sound of the horn wire guide spring steel rubbing against the steering wheel. Typically, the noise comes from inside the car and sounds like a rustling metal friction. Friction between plastic parts: The steering wheel is usually made of plastic components. If the temperature drops, the plastic parts may harden and produce friction noise. Aging of the steering tie rod ball joint: This can cause the car's steering wheel to shake and produce noise. It is recommended to replace the steering tie rod ball joint and perform a four-wheel alignment after replacement. Abnormal noise from the stabilizer bar: Loose or damaged stabilizer bar bushings can cause noise not only when turning the steering wheel but also when driving on uneven roads. Loose stabilizer bar bushings can be fixed by adding shims, but if they are damaged, they must be replaced.
7
1
Share

What is the size of the Nissan Bluebird wiper blades?

Nissan Bluebird wiper blades size is 26/14. Steps to replace Nissan Bluebird wiper blades: Open the external plastic cover of the old wiper blade, then push the old wiper arm slightly in the direction of the rod to expose the hook of the bracket. Remove it from the empty position and install the new one back. Open the external plastic cover of the old wiper blade, then push the old wiper arm slightly in the direction of the rod to expose the hook of the bracket. Remove it from the empty position and install the new one back. Precautions for using Nissan Bluebird wiper blades: Since the working part of the wiper relies on rubber products, it is best to avoid operations that may damage the rubber material. Do not operate the wipers dry. Also, during light rain, wait until a certain amount of rainwater has accumulated on the windshield before turning on the wipers. If the wipers are turned on when there is too little rain, it can easily create streaks and increase friction on the rubber part of the wiper blades.
15
1
Share

What Causes the Reversing Noise in Passat?

The causes of reversing noise in Passat are as follows: Noise occurs only at idle or low speed: Possible causes include: excessive clearance between piston and cylinder wall; overly tight piston pin assembly or connecting rod bearing assembly; excessive clearance between tappet and its guide hole; wear on the camshaft profile; sometimes, a loose starter clutch causing pulley noise (especially noticeable during speed changes). Irregular noise at a certain speed, with brief sounds during rapid deceleration: Possible causes include: cracked camshaft timing gear or loose fixing nut; broken crankshaft; loose piston pin bushing; excessive axial clearance of camshaft or loose camshaft bushing. Noise appears during rapid acceleration and persists at high speed: Possible causes include: loose connecting rod bearing, melted or mismatched bearing shell causing rotation; loose crankshaft bearing or melted bearing shell; broken piston pin; broken crankshaft.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.