What Causes the Steering Wheel to Become Hard to Turn?

1 Answers
DelStella
09/08/25 4:42am
Reasons why the steering wheel becomes hard to turn are as follows: Fluid Leakage: If the steering wheel suddenly becomes hard to turn, it could be due to fluid leakage or air not being completely expelled from the system. If the oil pump operates for a long time without sufficient oil, wear increases, reducing steering performance. Power Steering Failure: If the power steering fails, turning the wheel will feel very heavy. For women with less strength, it might become impossible to turn the wheel. Therefore, check if the power steering fluid level is too low or if the electric power steering has failed, and send it for repair promptly. Steering Wheel Lock: Another situation is when the steering wheel is locked and cannot be turned. After the vehicle is turned off for a period, the anti-theft system activates, automatically locking the steering wheel, which is a common anti-theft feature.
Was this review help?
12
5
Share
More Forum Discussions

What are the differences between low beam and high beam?

Regarding the differences between high beam and low beam, the introduction is as follows: 1. The difference between high beam and low beam lies in the distance they illuminate: one shines closer, and the other shines farther. Typically, the low beam illuminates a distance of about 30-40 meters with a coverage of approximately 160°, while the high beam has a more concentrated light with a larger bright spot, capable of illuminating higher and farther places. 2. High beams can be used when driving on highways or in rural areas without streetlights to expand the field of vision. 3. The high beam should be immediately switched to low beam under the following circumstances: first, when there is an oncoming vehicle; second, when the distance to the vehicle ahead in the same direction is relatively close; third, when the road is already sufficiently illuminated; and fourth, when entering busy streets with heavy traffic.
13
5
Share

What is the SAE oil grade?

SAE stands for the Society of Automotive Engineers, and the SAE grade represents the viscosity grade of the oil. Here is the relevant introduction about SAE: 1. SAE specifies 11 oil viscosity grades, indicating which grade of oil should be used at specific atmospheric temperatures. Winter oils are denoted by the letter W, including 0W, 5W, 10W, 20W, and 25W. 2. The number before the W indicates the lowest temperature at which the oil is suitable. The smaller the number, the lower the temperature. Summer oils are not denoted by letters but directly by numbers, including 20, 30, 40, 50, and 60, representing the highest temperature at which the oil is suitable. 3. API stands for the American Petroleum Institute, and the API grade represents the classification of engine oil quality. It uses simple codes to describe the working capability of engine oil.
20
1
Share

What is the lifespan of an AT transmission?

AT transmissions typically have a real lifespan of over ten years. Here are some details about transmissions: Advantages of AT transmissions: AT transmissions incorporate a long-stroke vibration damper in the torque converter, which effectively suppresses vehicle vibrations and provides noticeable noise reduction. Additionally, this transmission is equipped with two sets of planetary gears, which can effectively reduce vehicle fuel consumption. Models equipped with Aisin AT transmissions: Due to their advantages of reduced fuel consumption and noise, AT transmissions are widely used in mid-to-low-end models such as the Polo, Lavida, Bora, and Changan.
2
5
Share

What causes the ticking sound at idle that disappears when accelerating?

Ticking sound at idle that disappears when accelerating is typically caused by a faulty carbon canister purge valve, which should be replaced. The function of the carbon canister purge valve is to open the solenoid valve between the carbon canister and the intake manifold after the engine starts, allowing the adsorbed gasoline vapors in the carbon canister to enter the combustion chamber along with air for burning, thereby reducing emissions and fuel consumption. Below is relevant information about engine idling: 1. If the engine runs at idle for an extended period, the throttle opening will be very small, and the fuel injector will spray highly concentrated fuel to maintain engine operation. Therefore, idling itself is more likely to cause carbon buildup compared to driving or highway speeds. Prolonged idling will inevitably lead to more severe carbon buildup in the engine. 2. During engine idling, the temperature and pressure inside the cylinders are relatively low, prolonging the preparation time for fuel ignition. Additionally, the sealing performance of the cylinders decreases at this time, making it easier to produce knocking sounds and shortening the engine's service life.
18
5
Share

Where is the car condenser located?

The location of the car condenser is as follows: 1. The car air conditioning condenser is usually located at the very front, to utilize the incoming wind during driving to cool the refrigerant in the pipelines. 2. The function of the condenser is to convert the high-temperature, high-pressure liquid refrigerant from the compressor into a medium-temperature, medium-pressure refrigerant, which is then sent to the next stage's reservoir or dryer. 3. The process through the condenser is a highly effective cooling phase. If the condenser fails, it may lead to pipeline pressure imbalance and cause air conditioning malfunctions. 4. The structure of the condenser can be likened to a radiator, designed to increase the contact area and allow the refrigerant to achieve maximum heat exchange in the smallest possible space, similar to how a radiator works.
9
5
Share

Is Xiang A the License Plate for Changsha?

Xiang A is the license plate number for Changsha, Hunan. The first character of a license plate is a Chinese character representing the abbreviation of the provincial-level administrative region where the vehicle is registered. For example, "Xiang" stands for Hunan Province. The second character is an English letter, indicating the code for the prefecture-level city where the vehicle is located. Below is a related introduction to the license plates of various cities in Hunan Province: Changsha - Xiang A, Zhuzhou - Xiang B, Xiangtan - Xiang C, Hengyang - Xiang D, Shaoyang - Xiang E, Yueyang - Xiang F, Zhangjiajie - Xiang G, Yiyang - Xiang H, Changde - Xiang J, Loudi - Xiang K, Chenzhou - Xiang L, Yongzhou - Xiang M, Huaihua - Xiang N, Xiangxi Tujia and Miao Autonomous Prefecture - Xiang U.
1
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.