What Causes the Squeaking Noise When Releasing the Electronic Parking Brake?

What Causes Engine Resonance for Over Ten Minutes When Cold?

Cold start vibration is mainly caused by carbon deposits, weak ignition, low cylinder pressure, substandard fuel, etc. Detailed causes: Excessive carbon deposits on throttle body, fuel injectors, and intake passages; When there's excessive carbon buildup inside the engine, gasoline sprayed by the cold start injectors gets largely absorbed by the deposits, resulting in an overly lean air-fuel mixture during cold starts that causes vibration; Mechanical failures in ignition coils, spark plugs, or fuel injectors leading to cylinder misfires; Insufficient fuel pressure or cylinder pressure causing power deficiency; Poor fuel quality; Damaged or excessively dirty idle control valve; Intake manifold leaks; Damaged engine mounts or cushion pads; Oxidized or low-grade engine oil with poor low-temperature fluidity, leading to inadequate cold start protection. Recommendation: It's advisable to visit a 4S shop or repair facility for inspection and maintenance to enhance the vehicle's safety performance.

20

3

Share

What Causes Poor Rebound in Motorcycle Suspension?

Poor rebound in motorcycle suspension is caused by a broken or overly soft suspension spring. Inverted Suspension: Inverted suspension provides greater support to the vehicle body, which is beneficial for extreme driving and cornering. In the event of a collision, due to its strong rigidity, the triple clamp or frame is more likely to deform, which is the opposite of conventional suspension. The spring is less likely to be damaged in a fall. The piston moves upward from below. Conventional Suspension: It is thinner at the top and thicker at the bottom, with the mechanical structure of the suspension located below. It has a relatively longer travel, a simple structure, and is less prone to oil leakage. In a frontal collision, the suspension usually deforms, while the triple clamp is less likely to be damaged. However, its performance in motion is average, and it has some impact on the rigidity of the vehicle body. The spring is more likely to be damaged in a fall. The piston moves downward from above. Motorcycle Suspension: The function of motorcycle suspension is to elastically connect the frame and the wheels, absorbing and mitigating the impact and vibrations from uneven road surfaces on the frame. If the suspension is too hard, the vehicle will vibrate severely, and the rider will constantly experience shocks. If it is too soft, the vibration frequency and amplitude will make the rider uncomfortable.

7

1

Share

Can OnStar start the engine without the key?

Yes. OnStar has a remote control function, which allows you to start the engine even without the key. Remote Start: After remotely starting the engine via OnStar, bring the key into the vehicle's sensing area, press the brake pedal, and press the start button. When the light turns green, you can drive away. OnStar is a comprehensive wireless service that utilizes wireless technology and GPS satellites, allowing users to connect with a customer service center with just one button and receive full voice assistance to resolve issues. Features of OnStar Remote Start: High reliability with significantly reduced failure rates; convenient usage, enabling remote engine start anytime and anywhere; full vehicle heating to minimize cold-start wear on the engine, effectively protecting the vehicle; easy installation.

14

4

Share

What Causes Heavy Steering Wheel When Turning in Place?

Heavy steering wheel when turning in place occurs because rotating the steering wheel places an extreme load on the power steering system, which can easily cause the steering gear to overheat and activate protection mechanisms, resulting in stiff steering. Reasons for heavy steering: Issues with steering fluid, excessively tight meshing clearance between the steering gear pinion and rack, damaged bearings in the steering gear or steering column, power booster failure, severe over-wear of the power steering pump belt leading to low output pressure from the steering gear pump, insufficient power steering fluid, contaminated power steering fluid, low front tire pressure, inaccurate front wheel alignment, malfunction of the speed-sensitive solenoid valve on the steering gear (which controls the power assist level), or faults in the wiring or the solenoid valve itself. Steering system inspection methods: Check the ball joint for smooth rotation in its seat—normal operation should show slight resistance without sticking, but there should be no excessive play. Inspect the tie rod's coordination with the steering gear; if the steering wheel turns significantly while the tires don't move, adjust the tightness of the tie rod ball joint pin or replace the tie rod assembly. Examine the front axle and frame for deformation or cracks—replace if cracks or excessive deformation are found. Check the tie rod for damage and the ball joint seat for spalling or cracks. If the plastic ball seat shows obvious wear, thread damage exceeding 2 threads, or the ball joint pin's tapered neck protrudes 1-2 mm above the tapered hole's upper end, replacement is necessary.

2

5

Share

Where are the accelerator, clutch, and brake located?

Accelerator, clutch, and brake positions: Automatic transmission cars have only two pedals, from left to right, they are the brake pedal and the accelerator pedal. Manual transmission cars have three pedals, from left to right, they are the clutch pedal, brake pedal, and accelerator pedal. Normally, the left foot controls the clutch, while the right foot controls the brake and accelerator. The purpose of the brake is to decelerate, either to reduce speed or to bring the vehicle to a stop. The principle of braking is to convert the kinetic energy of the car into heat energy and dissipate it. The kinetic energy comes from the power provided by the engine, which requires fuel combustion to generate. In other words, every time you press the brake, it means a little bit of gasoline is wasted.

20

5

Share

What is the fuel tank capacity of new energy vehicles?

Binyue New Energy has a fuel tank capacity of 35L, while the fuel version has 45L. The fuel tank cap is located on the left side of the vehicle body and adopts an external opening method. Introduction to New Energy Vehicles: New energy vehicles refer to automobiles that use unconventional vehicle fuels as power sources (or use conventional vehicle fuels with new on-board power devices), integrating advanced technologies in vehicle power control and driving, resulting in advanced technical principles and featuring new technologies and structures. Types of New Energy Vehicles: New energy vehicles include pure electric vehicles, extended-range electric vehicles, hybrid electric vehicles, fuel cell electric vehicles, hydrogen engine vehicles, and other new energy vehicles.

18

0

Share

What Causes the Squeaking Noise When Releasing the Electronic Parking Brake?

What Causes Engine Resonance for Over Ten Minutes When Cold?

What Causes Poor Rebound in Motorcycle Suspension?

Can OnStar start the engine without the key?

What Causes Heavy Steering Wheel When Turning in Place?

Where are the accelerator, clutch, and brake located?

What is the fuel tank capacity of new energy vehicles?

What is the speed of a Formula car?

Is it mandatory to wear a full-face helmet for motorcycles?

What is the reason for the seat belt not fastening?

Can the Engine Still Run if the Connecting Rod is Broken?