What Causes the Scraping Sound When the Car is Running?

1 Answers
HaleyRose
07/30/25 6:54am
There are many possible reasons for noise during car driving: it could be due to engine oil issues, such as inferior quality oil, prolonged lack of oil changes, or insufficient oil levels. These conditions can easily increase friction between the valves and guides, as well as in hydraulic lifters, making various sounds within the engine more pronounced. Relevant information about engine oil is as follows: 1. Introduction: Engine oil, also known as engine lubricant (English name: Engine-oil), with a density of approximately 0.91×10³ (kg/m³), serves to lubricate and reduce wear, assist in cooling, seal against leaks, prevent rust and corrosion, and provide shock absorption. It is hailed as the 'blood' of the car. 2. Composition: Engine oil consists of base oil and additives. The base oil is the main component of lubricating oil, determining its basic properties, while additives compensate for and improve the shortcomings of the base oil's performance, endowing it with certain new characteristics, making them an important part of lubricating oil.
Was this review help?
15
4
Share
More Forum Discussions

Will an Unlocked Car Lead to Battery Drain?

Leaving the car doors unlocked can cause battery drain, but the amount is minimal. Modern vehicles have complex electrical systems with numerous power-consuming components such as audio systems, anti-theft devices, central locking, and power windows. These devices remain powered even when the ignition is turned off. Therefore, when the car is unlocked, related sensors and alert systems continue operating, consuming a small amount of power. Consequences of improperly closed doors: Interior dome lights stay on (approximately 5W per bulb), causing continuous power drain; the Body Control Module (BCM) remains active, consuming electricity; cabin lights may also stay illuminated (around 5W each); without turning on the ignition, the vehicle's hazard lights may activate when opening doors as a collision prevention measure, indicating that door sensors and control circuits remain operational; the vehicle maintains a minimum "sleep mode" current of about 80mA; if equipped with an anti-theft alarm, it continues consuming power to keep the remote signal receiver circuit operational even when disarmed. Car battery maintenance tips: Minimize electrical usage after engine shutdown. Many drivers tend to listen to the radio or use other electronics while waiting, which during prolonged parking can completely drain the battery - preventing engine start and reducing battery lifespan. Always check if headlights are turned off after nighttime driving.
3
0
Share

What brand is wildtrac tire?

wildtrac is a tire brand under Changluhong. Below are some tire maintenance tips: Regularly check tread depth: The thickness of the tire tread affects traction, drainage capability, etc. It's crucial to routinely inspect tread depth, which can be done using the built-in tread wear indicators on the tire or a tread depth gauge. Generally, attention should be paid when tread depth is less than 3mm, and immediate replacement is recommended when it's 1.6mm or less. Measure tire pressure: Maintain the tire pressure at the manufacturer's recommended value. Adjust if it's too high or too low.
5
2
Share

How many people can a two-wheeled motorcycle carry?

Legally, a two-wheeled motorcycle can carry one person aged 12 or older. Below are the relevant details: Regulations: According to Article 55 of the "Implementation Regulations of the Road Traffic Safety Law of the People's Republic of China," motor vehicles carrying passengers must comply with regulations. The rear seat of a motorcycle must not carry minors under 12 years of age, and light motorcycles are not allowed to carry passengers. Penalties: If a two-wheeled motorcycle carries one extra person (i.e., a total of three people, including the driver), even if the driver has all the necessary documents and all passengers are wearing helmets, the traffic police will impose a fine and deduct three points from the driver's license for the sole violation of overloading.
15
2
Share

Can You Reverse Along the Original Path in Left Reverse Parking?

Left reverse parking can be done along the original path. Below is the method for positioning during left reverse parking: Observe the position of the left rearview mirror and the parking line: Turn left one full circle plus 90 degrees when the left rearview mirror is still a short distance away from the parking line. For shorter individuals, this should be done a bit earlier, while taller individuals can wait until the rearview mirror reaches the parking line before turning fully. Check the position of the car body and the left corner of the parking space through the left rearview mirror: Predict whether the car body will cross the line. If continuing to reverse in the current direction causes the distance between the car body and the corner of the parking space to become too narrow, then turn the steering wheel back half a circle to widen the distance, and then turn fully again after the distance is widened.
3
2
Share

What is the Duan Tou Long motorcycle?

Duan Tou Long refers to the Benelli BN600. Below is an introduction to related motorcycle content: Working Principle: When the pedal is pressed, the mechanism pressurizes the spring, causing the outer edge of the spring to lift, and the pressure plate disengages from the friction plate. At this point, the friction plate and the flywheel are no longer connected, so even if the engine continues to run, the power is not transmitted to the gearbox and wheels. This allows the rider to shift gears or stop the motorcycle without stalling the engine. Power Transmission: When the crankshaft speed is low, the two friction plates do not contact the outer casing, and power cannot be transmitted. When the crankshaft speed is high, centrifugal force causes the friction plates to move outward and contact the outer casing, allowing power to be transmitted.
10
3
Share

What does 100cc mean?

100cc refers to the displacement of a motorcycle being 100 milliliters. Here is the relevant introduction: Calculation method of motorcycle displacement: Cylinder cross-sectional area X stroke X number of cylinders = total displacement in cc. Among these, stroke refers to the reciprocating movement of the piston in the cylinder. When the piston moves from the top dead center to the bottom dead center, the distance it travels is called the piston stroke, or simply stroke. Displacement: The larger the displacement, the greater the fuel consumption and horsepower. The smaller the displacement, the less fuel consumption and horsepower. 1cc = 1 milliliter, where milliliter is a unit of volume, with the main unit being liter (L). 1 milliliter = 1 cubic centimeter, and 1000 milliliters = 1 liter. 100CC refers to the displacement of a motorcycle, and a 125 motorcycle is a vehicle with a displacement of 125CC.
5
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.