What Causes the Santana to Shake When the Air Conditioning is On?

2 Answers
DiRonan
07/28/25 9:50pm
Santana shaking when the air conditioning is on may be caused by low engine idle speed due to the air conditioning. It is recommended to check the air conditioning idle speed and also inspect for excessive engine carbon buildup, which can lead to low idle speed. Solutions for Santana Shaking When the Air Conditioning is On: Clean the engine carbon buildup, replace the oil pad and spark plugs, check the fuel supply pressure and intake pressure sensor, clean the fuel system, and inspect the idle speed motor for carbon buildup, which should be cleaned if present. Santana Vehicle Maintenance: When starting the car cold, allow it to idle for one and a half minutes to give it a warm-up period. Avoid lugging the engine while driving, and downshift promptly when the engine starts to shake. Also, pay attention to the protection of the chassis.
Was this review help?
1
0
Share
Toby
08/12/25 2:26am
I recently encountered the issue of my Santana shaking when the AC is turned on, which is usually related to a sudden increase in engine load. When the AC is activated, the compressor needs to work and consumes power, forcing the engine to provide more power like it's on steroids, which can cause the idle to become unstable. Sometimes, it's an issue with the ignition system, such as old spark plugs not firing effectively, or clogged fuel injectors due to carbon buildup, preventing fuel from entering and causing unstable combustion. When I dealt with this before, I checked and cleaned the throttle body, and it worked quite well—dirt buildup on the throttle body can affect the engine's 'breathing.' If the belt is loose or the fan is stuck, the engine will struggle and shake when the compressor starts. It's best to visit a repair shop promptly to check idle parameters, compressor oil pressure, etc., using a diagnostic tool, so minor issues don't escalate into major engine repairs. AC-induced shaking not only affects comfort but can also damage other components, such as the fan failing to rotate, leading to cooling problems.
Was this review help?
3
5
Share
Expand All
More Forum Discussions

What is the Platinum car?

Platinum is the Ford Explorer, a mid-to-large-sized 5-door 7-seater SUV. Its body dimensions are: length 5064mm, width 2005mm, height 1798mm, with a wheelbase of 2860mm and a fuel tank capacity of 70.4 liters. The Ford Explorer is equipped with a 3.5T turbocharged engine, delivering a maximum power of 262 kilowatts and a maximum torque of 501 Newton-meters. It is paired with a 6-speed automatic transmission. The drivetrain is front-engine four-wheel drive, with a front suspension using MacPherson independent suspension and a rear suspension using multi-link independent suspension.
20
0
Share

What brand does the Wrangler belong to?

Wrangler is a brand under the American Chrysler. The Wrangler is a mid-size 2-door, 4-seat SUV with the following dimensions: length 4334mm, width 1894mm, height 1839mm, wheelbase 2459mm, and a fuel tank capacity of 70 liters. The Wrangler is equipped with a 2.0T turbocharged engine and an 8-speed automatic transmission, delivering a maximum power of 195.4 kW at 5000 rpm and a maximum torque of 400 Nm at 3000 rpm. It features a front-engine, four-wheel-drive layout and uses multi-link solid axle suspensions both at the front and rear.
1
1
Share

How to Open the Front Hood of Wuling Hongguang?

To open the front hood of the Wuling Hongguang, follow these steps: Enter the driver's seat, locate the front hood release lever, and pull it upwards until you hear a 'click' sound, indicating the hood is unlocked. The Wuling Hongguang is a microvan under SAIC-GM-Wuling, with body dimensions of 4390mm in length, 1660mm in width, and 1750mm in height, a wheelbase of 2720mm, and a fuel tank capacity of 50 liters. It is equipped with a 1.2L naturally aspirated engine and a 5-speed manual transmission, delivering a maximum power of 56 kW and a maximum torque of 110 N·m. The vehicle features a front-engine, rear-wheel-drive layout, with a MacPherson strut independent front suspension and a leaf spring non-independent rear suspension.
12
0
Share

How to Check the Engine Oil Level of Ford Escort?

The method to check the engine oil level of Ford Escort is: 1. Park the car on a flat surface and turn off the engine, waiting for a few minutes; 2. Pull out the oil dipstick and wipe it clean; 3. Reinsert it, then pull it out again to check if the oil level is between the two marked lines. If it is between the lines, it is normal. The Ford Escort is a compact 4-door 5-seater sedan with body dimensions of: length 4587mm, width 1825mm, height 1490mm, and a wheelbase of 2687mm. The Ford Escort is equipped with a 1.5L naturally aspirated engine and a 6-speed manual transmission, with a maximum power output of 90 kilowatts and a maximum torque of 152 Newton-meters. It features front-wheel drive, with a front suspension using MacPherson independent suspension and a rear suspension using a torsion beam non-independent suspension.
15
3
Share

What Causes a Car to Stall Easily at Idle?

The reasons why a car stalls easily at idle are: 1. Throttle blockage, carbon buildup, or abnormal opening; 2. Carbon buildup or blockage in the fuel injectors; 3. Spark plugs being burnt or damaged; 4. Use of low-quality gasoline, leading to fuel pump blockage; 5. Incomplete combustion of the air-fuel mixture in the cylinder. Solutions to prevent stalling at idle include: 1. Regularly cleaning the throttle; 2. Periodically cleaning the fuel injectors to prevent carbon buildup; 3. Replacing spark plugs; 4. Using gasoline from reputable gas stations. The reason a car stalls at idle is: After the engine starts, it runs well from low to high speeds, but stalls immediately when the accelerator pedal is released or first becomes unstable and then stalls.
4
2
Share

How to Control Speed with the Clutch?

Clutch control speed method: Use the heel of the left foot as a pivot point, place the ball of the foot on the clutch pedal, and press or lift using the ankle and knee. Precautions for clutch usage: 1. The clutch must be thoroughly cleaned before installation to remove anti-rust grease and debris; 2. The clutch can be installed coaxially or on separate shafts, but axial fixation is mandatory; 3. For wet electromagnetic clutches, lubricating oil must be added between the friction plates during operation; 4. Power and control circuits: The clutch operates on 24V DC power; 5. When installing a jaw-type electromagnetic clutch, ensure there is a gap between the end face teeth to prevent grinding during freewheeling.
10
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.