What Causes the Malfunction of the Golf's Central Control Screen?

What are the dimensions of FAW Senia?

FAW Senia has dimensions of 4120mm in length, 1640mm in width, and 1695mm in height, with a wheelbase of 2655mm. This is an MPV model, and the interior space of the vehicle is relatively spacious. The FAW Senia lineup is equipped with two engines: a 1.3-liter naturally aspirated engine and a 1.5-liter naturally aspirated engine. As a versatile and practical car, FAW Senia features strong power, spacious interior, small turning radius, and high ground clearance, providing family users with a comfortable driving experience and high utility value. The Senia is the first model of the Daihatsu brand in China, produced under a technical license agreement between Daihatsu and China FAW Group Corporation at FAW Jilin Automobile Co., Ltd.

8

0

Share

Do You Need to Press the One-Button Start Twice?

One-button start does not require pressing twice. After getting into the car, simply press the brake pedal and then press the button to start the engine. If you press the button without stepping on the brake pedal, the car will power on, and then pressing the button while stepping on the brake pedal will also start the engine. The one-button start device is part of a smart car system, serving as a button mechanism to simplify the ignition process, and it can also turn off the engine. This device can be retrofitted either at the original key lock position or as an independent panel. Nowadays, many cars utilize this smart feature to enhance market competitiveness. It can be installed in both high-end and low-end vehicle configurations, though a standalone one-button start has limited significance. When paired with a PKE smart system, it highlights the necessity of intelligent modifications.

15

5

Share

How to take out the spare tire of the Sylphy?

The method to take out the spare tire of the Sylphy is: remove the partition in the trunk, and then take out the spare tire from below. The specific steps for replacing the spare tire are: 1. Park the car on a flat and hard road surface, and turn on the hazard lights; in case of rain, snow, or fog, place a triangular warning sign about 100 meters behind the car; 2. Loosen the screws of the tire that needs to be replaced, then use a jack to lift the car; 3. After lifting the car, remove all the screws on the tire and replace it with a new one; 4. After installing the new tire, slightly tighten the screws and lower the car; 5. After lowering the car, fully tighten all the screws on the tire, and the spare tire replacement process is completed. The first generation of the Sylphy was born in 1959, originally named Bluebird, a term derived from the famous work of Belgian writer Maeterlinck, symbolizing the wish to bring happiness and well-being to ordinary families, which aligns perfectly with the car's positioning.

12

5

Share

What is the process of automotive beauty car washing?

There are fixed procedures for beauty car washing, and the following is a detailed introduction: 1. Choosing the right weather and environment for car washing: When washing your car, try to choose a windless sunny day. If it's windy, dust particles and pollutants in the air can settle on the paint surface, and wiping them off would be like rubbing the paint with sandpaper, causing fine scratches. Additionally, if pollutants land on the car, the effectiveness of the wash will be compromised. It's best to choose a day with mild temperatures. Overcast weather is not conducive to drying residual water, while excessively high temperatures can cause the vehicle's metal panels and paint to expand. Washing the car under such conditions can lead to rapid temperature changes, making the paint brittle and prone to cracking. 2. Selecting the correct car wash solution: Always use a dedicated car wash solution, preferably one containing wax components. Avoid strong alkaline detergents or soap powder, as they have strong cleaning power but can also cause significant damage. Frequent use can quickly erode the shine of the car's surface and accelerate the aging of rubber parts, tires, windows, etc. 3. Choosing the right tools and supplies: Car paint is quite fragile due to long-term exposure to the air and can easily chip. Therefore, never use tools like plastic brushes, ordinary towels, or coarse cloths. When cleaning the car body, use a soft and clean sponge, as the car surface usually has hardened dust and mud. Directly using high-pressure water jets is equivalent to letting dust particles perform a 'friction movement' on the paint. For cleaning windows, use a specialized glass cleaner and dry them with a clean towel instead of letting them air dry. For oil stains, gently wipe with a sponge dipped in kerosene or gasoline. For plastic and rubber parts like the steering wheel and lights, use ordinary soapy water and avoid organic solvents such as gasoline, stain removers, or thinners. 4. Rinse off the mud first: When using a high-pressure water gun, rinse the mud off the car surface from top to bottom. Then clean the rear of the car, and finally the lower part. Pay attention to thoroughly rinsing off mud from the wheels, brake discs, fenders, and grilles.

12

2

Share

What is the speed requirement for straight-line driving in C2?

The speed requirement for straight-line driving in C2 is no lower than 30km/h and no higher than 40km/h, with the optimal speed controlled at 36km/h. Assessment requirements for straight-line driving: The driver must start smoothly, control the speed properly, hold the steering wheel correctly, and use it to adjust the driving direction appropriately. The new regulations add the requirement that the left and right deviation distances should not exceed 50CM each. The steering wheel can be adjusted during straight-line driving, but the adjustment range should not exceed 5 degrees. Adhere to the principle of looking far and near. You should look far ahead while also paying attention to the nearby and rear conditions of the vehicle. In the third subject of the driving test, the driving speed is fast, so looking far ahead allows you to detect situations early and react in advance. At the same time, the vehicle is more likely to drive straight. Straight-line driving means maintaining the vehicle's straight-line movement, not keeping the steering wheel motionless. Generally, the right hand performs actions such as accelerating and shifting gears, while the left hand holds the steering wheel steadily and straight. Additionally, the steering wheel can be slightly adjusted during driving, but sudden and excessive movements should be avoided.

11

5

Share

What engine is used in the Baojun 530?

Baojun 530 is equipped with a 1.5T turbocharged engine, independently developed by Baojun, making it a domestically produced engine. The engine model used in the Baojun 530 is LL5, with a maximum power speed of 5500 rpm, maximum torque speed of 2000-3800 rpm, maximum power of 108 KW, maximum horsepower of 147 PS, and maximum torque of 250 N·m. For daily maintenance of the Baojun 530's engine, the following methods can be used: Use lubricating oil of appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, choose CB--CD grade diesel engine oil based on mechanical load, with the selection standard not lower than the manufacturer's specified requirements. Regularly change the engine oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, performance deteriorates, leading to various engine problems. To avoid malfunctions, change the oil regularly according to usage conditions and maintain an appropriate oil level. When oil passes through the fine pores of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter becomes clogged and oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing oil to bypass through the bypass valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal particles from component wear to form sludge. Small amounts remain suspended in the oil, while larger amounts precipitate, clogging filters and oil passages, making engine lubrication difficult and causing wear. Regularly use radiator cleaner to clean the radiator. Removing rust and scale not only ensures normal engine operation but also extends the overall lifespan of the radiator and engine.

8

5

Share

What Causes the Malfunction of the Golf's Central Control Screen?

What are the dimensions of FAW Senia?

Do You Need to Press the One-Button Start Twice?

How to take out the spare tire of the Sylphy?

What is the process of automotive beauty car washing?

What is the speed requirement for straight-line driving in C2?

What engine is used in the Baojun 530?

What does 'one oil' mean?

Why can't the fuel tank cover of the A6 be opened?

How many points are deducted for taking both hands off the steering wheel?

Why is the air conditioning cooling effect of the new Sylphy not good?