What Causes the Loud Roaring Sound When Accelerating?

1 Answers
LaJune
07/29/25 4:12pm
The loud roaring sound when accelerating can be attributed to the following reasons: 1. Engine Oil: Overfilling the engine oil increases the instantaneous working resistance of the engine, which raises the rotational resistance of the crankshaft and reduces the engine's power output. Additionally, excess oil may enter the combustion chamber and participate in combustion, leading to oil burning, blue smoke emission, and increased fuel consumption. 2. Engine Oil Type: Counterfeit or substandard engine oil can cause significant damage to the engine. Using the oil type recommended in the maintenance manual is generally safe. 3. Engine: Overheating of the engine can result in a loss of power. If the engine operates for an extended period, causing the surface to overheat, the cooling system may fail. The first step in such a situation is to check the cooling system. If the cooling system malfunctions, it could lead to exhaust blockage, as the vacuum tube may break. In this case, steam or hot air may escape from the engine, producing loud noises.
Was this review help?
18
2
Share
More Forum Discussions

How to Set Up a Car Remote Control?

Car remote control setup method: 1. Turn the ignition switch to ON; 2. Insert another key into the driver's side door lock and manually lock the door; 3. Press and hold the lock or unlock button for approximately 5 seconds; 4. Turn the ignition switch counterclockwise; 5. Press and hold the lock or unlock button for about 5 seconds, then remove the key to verify if the remote is functioning. Car remote controls generally consist of a transmitter, receiver, and antenna. Each remote for an electronic anti-theft car has a unique code, and only remotes recognized by the anti-theft control module can start the engine. If a car owner loses a legitimate remote, they must visit a service station to use a specialized diagnostic tool to rematch the remote, ensuring the lost remote cannot start the engine.
5
2
Share

Do You Need to Press the Brake When Turning Off an Automatic Transmission Car?

When turning off an automatic transmission car, you should press the brake. The correct sequence is: press the brake, shift to N gear, engage the handbrake, shift to P gear, turn off the engine, and then release the brake. For driving an automatic transmission car, using only the parking gear (P), reverse gear (R), neutral gear (N), and drive gear (D) is sufficient for normal driving needs. However, in some special driving conditions, other functional gears may be required. Manual transmission cars also require pressing the brake when turning off the engine. Otherwise, the vehicle may lurch forward due to lack of braking, potentially causing the engine to stall. The effectiveness of car braking depends on the quality of the brake pads. During the braking process, the brake pads are pressed against the brake discs or drums, creating friction to slow down or stop the car.
18
2
Share

How to Open the Hood of a Boyue Car?

Method to open the hood of a Boyue car: There is a hood lock handle in the gap between the front grille and the hood. First, lift the hood upwards to widen the gap, then pull the hood lock to release it. The front hood switch of the Boyue is located in the control area on the left side of the steering wheel, featuring an unlock button. Simply press it lightly, and the hood will pop up slightly with a "click" sound, indicating it is unlocked. However, pressing the engine hood unlock button inside the car does not fully open the hood. There is an additional latch located in the middle of the front hood. Only after releasing this latch can the engine hood be fully opened. The Boyue is a model under Geely, with body dimensions of 4519mm in length, 1831mm in width, and 1694mm in height, and a wheelbase of 2670mm. In terms of exterior design, the Boyue's front face continues Geely's family-style "water ripple" grille. The design inspiration for the chrome trim on the front fog lights comes from the Chinese jade Ruyi. The LED headlights, shaped like eagle eyes, are sharp in design, with a black and bright silver light bowl design, giving a strong three-dimensional effect.
13
4
Share

Where is the license plate number Gan S from?

Gan is the license plate prefix for Jiangxi Province. There is no Gan S license plate in Jiangxi. The license plate prefixes for various cities in Jiangxi are as follows: Gan A represents Nanchang, Gan B represents Ganzhou, Gan C represents Yichun, Gan D represents Ji'an, Gan E represents Shangrao, Gan F represents Fuzhou, Gan G represents Jiujiang, Gan H represents Jingdezhen, Gan J represents Pingxiang, Gan K represents Xinyu, and Gan L represents Yingtan. There are two types of license plates: temporary license plates and official license plates. Temporary license plates are made of paper and do not need to be mounted on the vehicle body; instead, they should be affixed to the front and rear windshields. Official license plates must be fixed to the vehicle body. It is important to note that temporary license plates have an expiration date. Driving with an expired temporary license plate is equivalent to driving without a license.
15
0
Share

What is the engine model of the Audi RS7?

The engine model of the Audi RS7 is CEU. The Audi RS7 is equipped with a 4.0T twin-turbocharged engine, which delivers a maximum power of 445 kW and a maximum torque of 750 Nm. In terms of the transmission system, the engine is paired with an 8-speed automatic manual transmission. The Audi RS7 features a fastback design with sharp design language, and the front fascia gives the car a strong sense of performance. The front end also incorporates the brand's signature headlights, which exude a powerful presence. The hexagonal grille on the front of the Audi RS7 is designed with a blackened finish, enhancing the car's sporty appeal.
10
4
Share

What is the maintenance reset method for the Mercedes-Benz C260L?

Maintenance reset method for the Mercedes-Benz C260L: 1. Start the engine and enter the odometer interface on the dashboard; 2. Press and hold the OK button on the left control area of the steering wheel while simultaneously pressing the phone button on the right side of the steering wheel, then a menu will appear; 3. Select ASSYST PLUS and press the OK button to enter; 4. Choose the full maintenance option and press the OK button to enter; 5. Select confirm full maintenance and press the confirmation button on the steering wheel; 6. The reset is complete. The Mercedes-Benz C260L has a length, width, and height of 4784mm, 1810mm, and 1457mm respectively, with a wheelbase of 2920mm. The Mercedes-Benz C260L features a front-engine rear-wheel-drive layout, with a front suspension type of multi-link independent suspension and a rear suspension type of multi-link independent suspension.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.