What causes the left side of the Audi A6 air conditioning to be cold and the right side hot?

2 Answers
EllieAnn
07/24/25 8:13am
Audi A6 experiencing cold air on the left and hot air on the right can be attributed to the following reasons: 1. Damage to the air conditioning warm water regulating valve, caused by an internal short circuit in the warm water valve. 2. Motor failure, leading to the inability to switch air ducts. Below is an introduction related to car air conditioning: 1. When the heating function is turned on, the high-temperature coolant from the car's engine flows through the heater core, and the air blown by the blower also passes through the heater core, allowing warm air to blow out from the air conditioning vents. 2. The cooling principle of car air conditioning is slightly more complex. After pressing the AC button, the compressor clutch engages, enabling the engine to drive the compressor. The compressor continuously compresses the refrigerant and sends it to the evaporator.
Was this review help?
19
3
Share
JosiahRose
08/11/25 3:51am
I worked at an Audi service center for many years and have encountered numerous cases of the Audi A6's left-side AC blowing cold while the right side blows hot. The cause is mostly a fault in the dual-zone climate control system, particularly when the air blend door actuator gets stuck or fails. In dual-zone AC designs, the actuator regulates temperature airflow to different zones—if the right-side actuator jams in the closed position or has insufficient power supply, it leads to cold air only from the left vents and hot air from the right. Another common culprit is faulty temperature sensor readings or loose wiring, often due to wear or dust buildup over time. I also recommend checking the coolant circulation, as the A6's dual-zone system relies on it to switch between heating and cooling sources. Don’t delay fixing this—visit a professional shop promptly to scan for trouble codes. Sometimes, simply cleaning the air blend door resolves it; otherwise, parts replacement (costing around a few hundred yuan) is needed. For safety, unstable AC can distract drivers, so regular maintenance helps prevent such issues.
Was this review help?
20
2
Share
Expand All
More Forum Discussions

Where is the central locking system located on the Baojun 310?

The central locking switch for the Baojun 310 is located on the left front door trim panel. Central control: When the driver locks their door, all other doors are simultaneously locked. The driver can use the door lock switch to open all doors at once or open individual doors separately. Speed control: When the vehicle reaches a certain speed, all doors automatically lock to prevent passengers from accidentally opening doors by operating the door handles. Working principle of central locking: When the central locking system receives the correct code signal, the control wave receiving circuit is triggered to extend reception time by 0.5 seconds before returning to standby mode. If the input code signal doesn't match, the receiving circuit won't be triggered.
3
1
Share

What are the reasons why an electric vehicle cannot start?

Reasons why an electric vehicle cannot start: 1. The battery is dead; 2. The controller is damaged; 3. There is a circuit malfunction. After encountering this situation, it is necessary to go to a professional repair facility for inspection and repair. Electric vehicles refer to vehicles that use electrical energy as a power source and are driven by electric motors. They belong to the category of new energy vehicles, including pure electric vehicles (BEV), hybrid electric vehicles (HEV), and fuel cell electric vehicles. Taking pure electric vehicles as an example, they are vehicles driven by electric motors. Compared to fuel-powered vehicles, the main differences of pure electric vehicles lie in four major components: the drive motor, speed controller, power battery, and onboard charger.
3
2
Share

What does the warning light on the Changan Kuayue Wang X1 indicate?

Warning light illumination indicates a fault in the electronic control system components or wiring. Below is relevant information about the Changan Kuayue Wang: 1. Vehicle Design: Compared to traditional single wheels, the dual-wheel design increases width, expands the contact area, reduces ground pressure, and thereby enhances the vehicle's load capacity. Additionally, the dual-wheel configuration provides a wider wheelbase, ensuring driving stability. 2. Power: In terms of powertrain, the Kuayue Wang X1 is equipped with a robust 88-horsepower engine. This power configuration fully meets daily cargo transportation needs. Moreover, the Kuayue Wang X1's powertrain emissions fully comply with China VI emission standards while being fuel-efficient, with a combined fuel consumption of only 7.3L/100km.
3
2
Share

What is the maximum speed of the Audi A3 during the break-in period?

The maximum speed of the Audi A3 during the break-in period is 100 kilometers per hour. The break-in period refers to the initial driving distance after a new car leaves the factory, during which the engine components are allowed to wear in smoothly. The Audi A3 is a 5-door, 5-seat hatchback with the following dimensions: length 4351mm, width 1815mm, height 1458mm, wheelbase 2630mm, and a curb weight of 1400kg. The Audi A3 is equipped with a 1.4L turbocharged engine, delivering a maximum horsepower of 150PS and a maximum power of 110kW, paired with a 7-speed dual-clutch transmission.
10
3
Share

How to Remove the License Plate Light on a Bluebird?

To remove the license plate light on a Bluebird, follow these steps: 1. You will need a flathead screwdriver to remove the license plate light. Locate the clip of the license plate light and gently pry it open. 2. Twist the rear connection clockwise, then remove and replace the bulb. Additional information about the license plate light: 1. The license plate light is used to illuminate the license plate at night or in low-light conditions, and it is turned on together with the parking lights. 2. According to regulations, all vehicles must have their rear license plate lights turned on while driving at night. The brightness of the rear license plate light must allow a person with normal vision to clearly read the license plate number from within 20 meters at night. The license plate light must also be controlled by the same switch as the parking lights.
14
1
Share

Where to Find the Manufacturing Date of the Envision?

There is an automotive nameplate on the door frame of the passenger side, which indicates the manufacturing date. Vehicles must be equipped with a product nameplate, placed in an easily observable location at the front of the vehicle. Introduction to the Vehicle Nameplate: The vehicle nameplate is a label that indicates the basic characteristics of the vehicle, including the brand, model, engine power, total weight, load capacity or passenger capacity, manufacturing number, manufacturing date, and manufacturer name. Function of the Vehicle Nameplate: The manufacturing date can be confirmed by inquiring with the user or by checking the vehicle nameplate, as the vehicle nameplate in the driver's compartment will always display the manufacturing date.
1
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.