What causes the high water temperature and non-rotating fan in a Fukang car?

What Causes the Ford ABS Yellow Light to Illuminate?

ABS warning light can illuminate in various states, each with different causes and solutions. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt on the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections between system lines or poor contact in the ABS relay, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple vehicle electrical devices are used, the battery voltage drops below 10.5V. The ABS warning light turns off as the engine speed increases and voltage rises. The ABS system power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wire connector; ABS computer malfunction. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant difference between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, push the brake switch linkage down with a finger, then release the brake pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is on, it is advised not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's path, posing significant safety risks.

16

2

Share

Why do 4S stores require vehicle license photos?

4S stores require vehicle license photos for real-name registration. Here is an extended introduction about vehicle license photos: 1. Reason for requirement: As the number of motor vehicles increases, crimes such as hit-and-run and traffic accident evasion have also risen. Real-name registration of motor vehicles plays a significant role in protecting public and social safety. 2. Functions and benefits: Implementing a real-name repair system has three major functions. (1) Query records. Car owners can check their vehicle repair history. (2) Provide clues. Traffic management departments can use these clues to locate vehicles involved in hit-and-run accidents. (3) Locate vehicles. It helps car owners find lost vehicles.

14

3

Share

What engine is used in the BMW 8 Series?

The BMW 8 Series is equipped with a 3.0-liter inline six-cylinder turbocharged engine, delivering a maximum torque of 500 Nm. The engine reaches its peak power output between 5,000 to 6,500 rpm, with maximum torque available from 1,600 to 4,500 rpm. This powerplant features direct fuel injection technology and utilizes an aluminum alloy cylinder head and block, paired with an 8-speed automatic transmission. As BMW's flagship coupe, the 8 Series measures 5,088mm in length, 1,932mm in width, and 1,410mm in height, with a wheelbase of 3,023mm. The front fascia showcases BMW's signature kidney grille with a blackened design, flanked by slim laser headlights on both sides.

11

4

Share

How to Deal with Sulfation of Battery Plates?

For sulfation of battery plates, the low-current charging method can be used for treatment. The specific steps are as follows: 1. First, add pure distilled water to the electrolyte to reduce the specific gravity to below 1.2, ensuring the liquid level reaches the upper standard line. 2. Charge with half the current of the 10-hour discharge rate. When bubbles start to appear and the voltage reaches about 2.4V, stop charging for 30 minutes. 3. Reduce the charging current to one-fourth of the 10-hour discharge rate and continue charging until vigorous bubbling occurs on both the positive and negative plates, then stop charging for 20 minutes. 4. Continue charging with half the current of the 10-hour discharge rate until the battery returns to normal. 5. Note: Do not arbitrarily add acid to the battery during the charging process, and ensure the specific gravity of the electrolyte does not exceed the specified value.

2

5

Share

What is Semi-Synthetic Engine Oil?

Semi-synthetic engine oil is a lubricant formulated from Group III base oils, which is a purified product derived from mineral oil through hydrocracking technology. Specifically, it is made by blending mineral oil and fully synthetic oil in a 4:6 ratio, with the addition of certain additives. Here are some relevant details: 1. Semi-synthetic engine oil is generally suitable for mid-to-low-end naturally aspirated engine models. As long as it's not for turbocharged engines or high-end, large SUV models, semi-synthetic oil can be used. 2. The replacement cycle for semi-synthetic oil is approximately 8 months, typically around 7,000 kilometers. There is no fixed interval for oil changes; it depends on the actual driving environment and habits. In harsher driving conditions, an earlier replacement is necessary, and the type of oil used should also refer to the recommendations in the vehicle's maintenance manual.

20

2

Share

How many types of engines are used in the BMW 7 Series?

The BMW 7 Series uses 4 types of engines, which are: 1. A 2.0-liter turbocharged engine with a maximum torque of 400 Nm and a maximum power speed of 5000 to 6500 rpm; 2. A 3.0-liter turbocharged engine with a maximum torque of 450 Nm and a maximum power speed of 5500 to 6500 rpm; 3. A 4.4-liter twin-turbocharged engine with a maximum torque of 750 Nm and a maximum power speed of 5500 to 6000 rpm; 4. A 6.6-liter twin-turbocharged engine with a maximum torque of 1850 Nm and a maximum power speed of 5250 to 5750 rpm. The BMW 7 Series is BMW's flagship sedan, with dimensions of 5212mm in length, 1902mm in width, 1478mm in height, and a wheelbase of 3210mm.

17

5

Share

What causes the high water temperature and non-rotating fan in a Fukang car?

What Causes the Ford ABS Yellow Light to Illuminate?

Why do 4S stores require vehicle license photos?

What engine is used in the BMW 8 Series?

How to Deal with Sulfation of Battery Plates?

What is Semi-Synthetic Engine Oil?

How many types of engines are used in the BMW 7 Series?

What Documents Are Required to Collect New License Plates?

How to Use a Serpentine Gear Shift?

Should the older GL8 use 92 or 95 octane gasoline?

What is the actual fuel consumption of the Buick Excelle 1.5L?