What Causes the Front Wheels to Make Abnormal Noises When Driving Over Speed Bumps?

1 Answers
McTaylor
07/29/25 4:58pm
When a car makes a clunking noise while driving over speed bumps, it is usually caused by a loose stabilizer bar or a faulty shock absorber. Generally, shock absorbers themselves rarely produce abnormal noises. However, noises can occur if the shock absorber fails, deteriorates, has loose or detached internal components, has a loose rubber bushing on the mounting ring, or lacks oil or leaks oil. It is recommended to promptly inspect and repair the vehicle when such noises occur. Below is some related information about speed bumps: 1. Speed bumps, also known as speed humps, are traffic installations placed on roads to slow down passing vehicles. They are typically strip-shaped, though some are dot-shaped, and are primarily made of rubber, though some are metal. They are usually painted in alternating yellow and black colors to attract visual attention, with a slight elevation on the road surface to force vehicles to slow down. 2. Speed bumps are commonly installed in areas where vehicles need to reduce speed, such as road intersections, industrial and mining zones, schools, residential entrances, and accident-prone sections. They are a specialized traffic safety measure designed to reduce the speed of both motorized and non-motorized vehicles.
Was this review help?
10
1
Share
More Forum Discussions

How to Activate BMW Automatic Wipers?

First, press the one-touch start button to power on the vehicle. The "AUTO" mode is the automatic sensing setting, which activates wipers based on actual rainfall intensity. You can adjust the sensitivity of the sensor using the central scroll wheel. If the actual wiping frequency in low-speed or high-speed modes is unsatisfactory, you can fine-tune the frequency via the central scroll wheel.
5
4
Share

How to check the remaining fuel level in Borgward BX7?

There is a small button at the bottom center of the Borgward BX7 instrument panel. Each press displays the total mileage, average fuel consumption per 100 kilometers, and the remaining kilometers that can be driven with the current fuel. The pointer type indicates the amount of fuel through the position of the pointer. The fuel gauge is marked with two letters, E and F, where F stands for full and E stands for empty.
1
1
Share

How to Remove the Porsche 718 Key?

First, after parking, straighten the steering wheel. If the steering wheel is not straightened, the vehicle may not drive straight when starting. To turn off the key, generally twist it twice in steps: first twist to the position to shut off the engine, then twist in the opposite direction to the end to completely turn off the car. Finally, you can pull out the car key. After removing the key, always remember to close the door and lock the car.
11
4
Share

How to turn on the headlights of the Borgward BX7?

Enter the driver's cabin and locate the vehicle's light control lever. The "0" position turns off the vehicle lights. The "AUTO" position activates the automatic light function. Adjust the light control to the position light setting. Turn the knob to the right position for the low beam setting. Push the light lever upward for the right turn signal and downward for the left turn signal. Push the vehicle light lever forward for the high beam setting and pull it backward for the single high beam flash.
12
4
Share

How to reset the tire pressure on a Porsche Macan?

First, turn the one-touch start button on the left side of the steering wheel to start the vehicle; otherwise, the tire pressure cannot be reset. Then, press the custom button on the right side of the multifunction steering wheel. Next, press the '+' button on the left side of the multifunction steering wheel. After that, use the lever below the steering wheel, push it downward, and select the clear function. Finally, observe the tire pressure information on the dashboard to confirm that the tire pressure has been reset.
8
4
Share

How to Turn Off and Power Down the Borgward BX5?

First, firmly press the brake pedal to keep the vehicle stationary and prevent it from moving. This avoids potential scratches or collisions with other objects. Next, shift the gear to neutral, release the clutch while keeping the brake pedal depressed. Turn off the ignition and remove the key, then open the door to prepare for exiting the vehicle. Finally, after exiting the car, press the logo button on the key once to completely cut off power and shut down the engine.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.