What Causes the Engine to Make Loud Noises When Accelerating?

1 Answers
DiGage
07/30/25 8:02am
Reasons for loud engine noises when pressing the accelerator include: 1. Engine overheating causing loss of power. 2. Blocked internal engine valves. 3. Exhaust pipe leakage. 4. Dirty or clogged throttle. 5. Engine misfire (cylinder failure). 6. Low power steering fluid. 7. Damaged generator bearings. 8. Issues with power steering pump or water pump. Below is relevant information about the accelerator: The accelerator, also known as the throttle, controls engine power output. The driver operates the throttle lever in the cockpit, which transmits commands through the control system to the carburetor or fuel regulator on the engine.
Was this review help?
9
0
Share
More Forum Discussions

What does the autohold function mean?

autohold function is the automatic parking function, which refers to a function that allows the driver to avoid unnecessary sliding of the vehicle without the need for long-term braking or activating the electronic parking brake. The automatic parking function can automatically activate the four-wheel braking when the vehicle is waiting for a red light or stopping on a slope. Even in D gear or N gear, there is no need to keep stepping on the brake or using the handbrake, and the car will always remain stationary. The autohold automatic parking function provides accurate parking force through the slope sensor by the controller. When starting the car, the parking control unit calculates the information provided by the clutch distance sensor, clutch engagement speed sensor, throttle pedal sensor, etc. When the driving force is greater than the driving resistance, the parking brake is automatically released, so that the car can start smoothly.
12
5
Share

What is the difference between Reiz 2.5v and Reiz 2.5s?

Differences between Reiz 2.5v and Reiz 2.5s: Sunroof configuration differs: The Reiz 2.5v is equipped with an electronically controlled electric sunroof; the Reiz 2.5s does not have a sunroof. Seat adjustment methods differ: The Reiz 2.5v uses electronic switch electric adjustment; the Reiz 2.5s uses manual mechanical adjustment. Heating methods differ: The Reiz 2.5v is equipped with air conditioning warm air and heating for both the driver and front passenger seats; the Reiz 2.5s is equipped with air conditioning warm air. The Reiz is the domestic name for the Japanese Toyota MARKx model, which is produced on the same line as the Crown at Tianjin FAW Toyota Plant 2, sharing the same chassis and equipped with the same six-speed automatic transmission as the Crown.
18
2
Share

What are the symptoms of a faulty EGR valve?

egr valve failure symptoms include: 1. The exhaust gas recirculation valve gets stuck in the fully open position and cannot close completely, causing the vehicle to emit black smoke along with symptoms like poor acceleration, unstable idle, increased fuel consumption, and insufficient power; 2. The exhaust gas recirculation valve gets stuck in the closed position and cannot open fully, which affects the vehicle's emissions. The EGR valve, or exhaust gas recirculation valve, is typically located on the right side of the intake manifold, near the throttle body, and is connected to the exhaust manifold via a short metal pipe. Exhaust gas recirculation is a technology (or method) used in small automotive internal combustion engines where a portion of the exhaust gases is recirculated back into the intake side for re-combustion. Its primary purpose is to reduce nitrogen oxide (NOx) emissions in the exhaust gases and improve fuel economy under partial load conditions.
17
5
Share

How to Determine if the Charcoal Canister Solenoid Valve is Faulty?

Methods to determine if the charcoal canister solenoid valve is faulty: 1. The fuel nozzle shuts off prematurely when refueling or gas escapes when opening the fuel tank cap; 2. Gasoline vapor or dripping fuel appears at the charcoal canister's atmospheric vent; 3. Poor acceleration, jerking, unstable idle speed, fluctuating between high and low; 4. Engine stalls and fails to start, unusual noises while driving. The charcoal canister is typically installed between the fuel tank and the engine. Its primary function is to adsorb and filter fuel vapors from inside the fuel tank, allowing them to enter the engine for combustion via the solenoid valve's control, thereby reducing fuel consumption and preventing excessive pressure in the fuel tank. If the charcoal canister solenoid valve malfunctions, it can significantly impact the vehicle. It is essential to seek repair immediately to prevent further damage.
15
4
Share

What is the function of the fuel injector?

The fuel injector mainly consists of three parts: the starting circuit, the cold fuel injector, and the thermal time switch. The function of the cold start fuel injector is to inject fuel into the intake manifold during engine cold starts to enrich the air-fuel mixture and improve the engine's cold start performance. The cold start fuel injector is also known as an auxiliary fuel injector or cold start electric valve, which enhances the engine's low-temperature starting performance. The advantages and disadvantages of the cold start fuel injector are as follows: 1. Advantages: To a certain extent, it can improve the difficulty of engine cold starts. 2. Disadvantages: Since the cold start fuel injector injects fuel into the intake manifold, there is a drawback of uneven fuel supply to each cylinder.
16
0
Share

How to adjust the reversing camera on Lavida?

Check if there are settings for original image and mirror image in the navigation system. If not, you can try the following operation: when reversing, the reversing image is displayed, click the upper left corner or lower right corner of the screen. Here is some relevant information: 1. The reversing camera is also known as the parking assist system, or reversing visual system, on-board monitoring system, etc. This system is widely used in various large, medium and small vehicles for reversing or driving safety assistance. This system makes the situation behind the car more intuitive and clear when reversing, which is one of the very practical configurations for reversing safety. 2. When selecting a reversing camera, you need to pay attention to whether it matches your car model. You can consider the camera model, power supply voltage, screen size, whether it is waterproof, shockproof, anti-interference, etc. When selecting products, be sure to choose the right product, not determined by price or other factors.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.