What Causes the Engine Malfunction Light to Stay On?

1 Answers
Cindy
07/29/25 10:09am
There are mainly 7 reasons for the engine malfunction light to illuminate: Sensor failure: The sensors mentioned here include coolant temperature, crankshaft position, air flow, intake air temperature, oxygen sensors, etc. When these sensors are damaged, have poor contact, or signal interruption, the car's ECU cannot accurately obtain engine data, which will trigger the engine malfunction light. Fuel quality issues: If fuel and engine oil are not added as required by the manufacturer, it may cause engine wear and trigger the malfunction light. Poor mixture combustion: Poor mixture combustion can lead to engine carbon deposits or knocking. When detected by the oxygen sensor and reported to the ECU, the malfunction light will illuminate as a warning. Spark plug failure, ignition coil failure, fuel pump failure, and fuel line blockage can all cause poor mixture combustion in the engine. Turbocharging issues: Intake turbocharging pipes and turbochargers can also cause the engine malfunction light to illuminate. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, high oil consumption, reduced power, metal noises, and blue or black smoke from the exhaust pipe. Intake issues: If there is a problem with the car's intake, it may cause engine pipe blockage, and in severe cases, trigger the engine malfunction light. A dirty air filter that is not cleaned regularly can lead to intake problems. Exhaust issues: Exhaust faults can also cause the engine malfunction light to illuminate. Rear oxygen sensor, catalytic converter, exhaust camshaft, and bearing failures are all causes of exhaust problems, with the catalytic converter being the most common. Using leaded gasoline, lead or silicon-containing lubricant additives, physical damage to the catalytic converter, or engine fuel system failures can easily cause catalytic converter issues. Anti-theft system failure: If the car's electronic anti-theft system malfunctions or the anti-theft controller does not match the engine electronic controller, the anti-theft system can prevent the engine from operating normally and trigger the malfunction light. If the engine malfunction light is on, follow these steps: First, check if the engine is running normally and if there are any issues like shaking or smoke. If so, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can start, turn it off for 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the "on" position without pressing the clutch. The car will perform a self-check after powering on. Wait 5-10 seconds and observe if the malfunction light on the dashboard turns off. If the light remains on, visit a service center as soon as possible. The service center can use a portable diagnostic tool to read the fault code, identify the issue, and perform targeted repairs.
Was this review help?
7
2
Share
More Forum Discussions

What is the normal pressure for a car's air conditioning system?

The normal high pressure for a car's air conditioning system is 1.3-1.7MPa (13-17kg/cm2 or 190-250Lbf/in2); the normal low pressure ranges between 0.15-0.25MPa (1.5-2.5kg/cm2 or 20-35Lbf/in2). The following is an introduction to car air conditioning: 1. Definition of car air conditioning: The car air conditioning system is a device that cools, heats, ventilates, and purifies the air inside the vehicle compartment, providing a comfortable environment for passengers, reducing driver fatigue, and improving driving safety. 2. Application of car air conditioning: Most cars use an integrated heating and cooling air conditioning system. The layout typically combines the evaporator, heater radiator, centrifugal blower, and control mechanism into a single unit, known as the air conditioning assembly.
17
5
Share

Where is the Temperature Control Switch for the Car Electric Fan?

Car electric fan temperature control switch locations are divided into two scenarios: older models and newer models. In older models, the temperature control switch is mostly on the radiator, typically with three wires controlling the high and low-speed fans. Nowadays, most cars use computer-controlled fans, with the water temperature sensor installed near the thermostat. Below is an introduction to how car fans work: The high and low speeds of the car fan are "uniquely" controlled by the thermal switch (F18), which sends two-stage signals to J293. J293 then activates different open circuits to control the high and low speeds of the electric fan. When the air conditioning is turned on, both fans should operate. However, it should be noted that the air conditioning and the electric fan are two relatively independent systems, controlled by two separate computers named J301 (air conditioning) and J293 (electric fan).
18
5
Share

What Causes a Car to Lose Acceleration When the Air Conditioner is On?

Reasons for a car losing acceleration when the air conditioner is on: Turning on the air conditioner increases the engine load, especially during hot summer days when fuel vapor increases relatively, leading to a decrease in fuel pressure within the fuel system. Insufficient fuel supply due to a clogged fuel filter can also contribute to this issue. Below is an introduction to car air conditioning: 1. Definition of car air conditioning: The car air conditioning system is a device designed to cool, heat, ventilate, and purify the air inside the vehicle compartment. It provides a comfortable environment for passengers, reduces driver fatigue, and enhances driving safety. 2. Application of car air conditioning: Most cars widely use an integrated heating and cooling air conditioning system. The layout typically combines the evaporator, heater radiator, centrifugal blower, and control mechanisms into one unit, known as the air conditioning assembly.
11
2
Share

How to distinguish between the low-pressure pipe and high-pressure pipe of a car air conditioner?

To distinguish between the high-pressure and low-pressure pipes in a car air conditioner, observe the thickness of the pipes and compare their temperatures. Generally, the thicker pipe is the low-pressure pipe, which feels cool to the touch during operation. The low-pressure side includes the evaporator, accumulator, return pipe, compressor input side, and compressor oil sump. The thinner pipe is the high-pressure pipe, which feels hot to the touch during operation. The high-pressure side includes the compressor output side, high-pressure pipe, condenser, receiver-drier, and liquid pipe. Here is some additional information about car air conditioners: 1. Definition of a car air conditioner: The car air conditioning system is a device that cools, heats, ventilates, and purifies the air inside the vehicle, providing a comfortable environment for passengers, reducing driver fatigue, and improving driving safety. 2. Application of car air conditioners: Most cars use an integrated heating and cooling air conditioning system. The layout typically combines the evaporator, heater core, centrifugal blower, and control mechanism into a single unit, known as the air conditioner assembly.
9
1
Share

What is an automotive chip?

Automotive electronic chips, collectively referred to as automotive chips, are chips used in vehicles. IC chips, or integrated circuits, encompass all electronic components. They integrate multiple electronic components on a silicon substrate to form a circuit module that performs specific functions, serving as the most crucial part of electronic devices by handling computation and storage. Below is an introduction to the classification of automotive chips: 1. Types responsible for computing power: Specifically, processor and controller chips, such as those used in central control units, ADAS (Advanced Driver Assistance Systems), autonomous driving systems, as well as engine, chassis, and body control. 2. Types responsible for power conversion: Used for power supplies and interfaces, such as IGBT (Insulated Gate Bipolar Transistor) power chips for EVs. 3. Types acting as sensors: Mainly used in various radars, airbags, and tire pressure monitoring systems.
6
0
Share

How is the comprehensive fuel consumption of a car calculated?

The calculation method of comprehensive fuel consumption for a car: Calculate fuel consumption through the relationship between distance and speed. 1. Record the mileage: Fill the car with fuel until the pump automatically stops, and record the current mileage. 2. Record the amount of fuel added: The next time you refuel, fill it until the pump automatically stops again, and record the amount of fuel added. 3. Calculate using the formula: Calculate the distance traveled since the last refueling, and then determine the fuel consumption based on the relationship between distance and speed. Below is an introduction to a more scientific method for calculating fuel consumption: Personal driving habits, road conditions, vehicle load, tire pressure, and weather can all affect fuel consumption, making it vary. A more scientific approach to calculating fuel consumption involves determining the average value. By recording data from multiple refueling sessions over a distance of 10,000 kilometers, and then taking the average of the highest and lowest fuel consumption values, the resulting data is relatively more scientific.
18
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.