What causes the electronic steering lock failure warning in the Baojun 510?

1 Answers
Philip
07/29/25 5:55pm
The electronic steering lock failure warning in the Baojun 510 is usually caused by the following reasons: the oil cup is too dirty inside, the filter screen is blocked, or the oil level in the oil cup is low; there is a large amount of air in the power steering system; foreign objects in the steering system cause the steering pump flow control valve to stick, etc. Relevant introduction about the automobile power steering pump is as follows: 1. Classification: Automobile power steering pumps are mainly divided into steering power pumps and brake power pumps. 2. Steering power pump: As the power source of automobile steering, it is the "heart" of the steering system. The brake power pump is a vacuum chamber with a larger diameter. There is a diaphragm (or piston) with a push rod in the middle inside, which divides the chamber into two parts. One part is connected to the atmosphere, and the other part is connected to the engine intake pipe through a pipeline.
Was this review help?
11
3
Share
More Forum Discussions

How to Replace the Battery in a BMW 320 Key?

To replace the battery in a BMW 320 key, follow these steps: First, remove the key from the remote. You will see a small square on the key. After removing the battery, simply install the new one. Here are more details about car batteries: 1. Once the battery is depleted, it cannot be recharged. You need to remove this battery and install a new one, ensuring the positive side is facing up. 2. When the remote control distance becomes shorter, such as needing to bring the key closer to the car door to unlock it, this indicates that the battery in the key remote is running low and needs replacement.
6
5
Share

What are the penalties for changing lanes without signaling?

Changing lanes without signaling will result in a one-point deduction on the driver's license and a certain amount of fine. Below are relevant details: 1. Signaling precautions: According to national regulations, when overtaking, motor vehicles should turn on the left turn signal in advance, switch between high and low beams, or honk the horn. When turning left, changing lanes to the left, preparing to overtake, leaving a parking spot, or making a U-turn, the left turn signal should be activated in advance. When turning right, changing lanes to the right, returning to the original lane after overtaking, or parking by the roadside, the right turn signal should be activated in advance. 2. Lane-changing precautions: When changing lanes to the left or right, it should not be done too slowly. Driving with the wheels on the lane markings for a long distance will affect other vehicles. The optimal distance for changing lanes is between 50 to 60 meters. Additionally, when encountering intersections while changing lanes, choose the lane based on the intended direction of travel and follow the directional arrows on traffic signs to enter the guiding lane. If there is an obstacle while changing lanes, do so in advance to prevent collision accidents caused by forced lane changes. When changing lanes, it is not allowed to ride on the lane divider line, the solid center line, or the solid edge line for an extended period. You can only change to an adjacent lane. If you need to change to a farther lane, first change to the adjacent lane, drive for a while, and then change to another lane.
16
1
Share

What is the explanation of the manual-automatic transmission gears in the Epica?

Epica manual-automatic transmission gear explanation: 3 is the forward gear, where the transmission automatically shifts between 1st to 3rd gears. 2 indicates 2nd gear, where the transmission stays in 2nd gear. 1 is 1st gear. S gear and L gear. S stands for Sport mode, where the transmission can shift freely in this gear. L stands for Low gear, where the transmission remains in 1st gear without shifting up. Introduction to manual-automatic transmission: In manual-automatic vehicles, when shifting from automatic D to manual M, the clutch or brake used for a specific gear remains fixed. For example, in a 6AT transmission driving in D gear at 3rd gear, switching to M gear keeps the transmission in 3rd gear. While driving in 3rd gear, the 35R and UD clutches inside the transmission remain engaged, keeping the transmission fixed in 3rd gear. Principle of manual-automatic transmission: When the driver shifts from D to M, it does not involve switching between different gear clutches but only changes the transmission control logic. The transmission remains in a specific gear, where the TCU cannot shift gears automatically, requiring the driver to shift manually. If the driver wants to drive in a lower gear, the engine speed increases significantly, enhancing the vehicle's acceleration capability. If the driver prefers a higher gear, the engine speed is lower, making the vehicle more fuel-efficient and providing a more comfortable ride.
19
0
Share

How to Adjust Seat Recline Angle?

Proper height ensures visibility. When adjusting the seat, height adjustment should be the first step. Ensure there is at least a fist's distance between your head and the car roof. For daily driving, the seat back recline angle should be between 100-110 degrees. When the backrest angle exceeds 110 degrees, intervertebral disc pressure significantly decreases, which is an important reference. Except for people with special height requirements, positioning the seat too far forward or backward is incorrect adjustment. If the seat is too far forward, it will reduce limb movement space.
12
3
Share

Does the current Passat consume engine oil?

Passat vehicles do experience engine oil consumption. More information about engine oil consumption is as follows: 1. As long as the engine is running, there will be engine oil consumption, the only difference being the amount. A small amount of oil consumption is normal, but if the oil consumption is too high, it is necessary to go to a professional repair shop for inspection and maintenance to eliminate faults; 2. Engine oil consumption design value: This is the normal engine oil consumption considered during the design of the car. For imported foreign models, this value is generally 0.1-0.2g/kwh, and it is higher for German models. In China, the regulation states that engine oil consumption should be less than 1% of gasoline consumption to be considered normal; 3. Engine oil consumption calculation formula (only an approximate calculation): Engine oil consumption = (mileage/average speed) * car power * engine oil consumption design value. 4. There are certain reasons for engine oil consumption: Engine oil has the function of lubricating pistons, piston rings, and cylinders. When the piston engine is working, there is a layer of oil film on the inner wall of the cylinder. During the combustion of the mixed gas, part of the oil film will be burned off by the high-temperature combustion gas; The engine oil used to lubricate the intake valve stem will also be sucked into the combustion chamber. High-temperature exhaust gas will also consume the engine oil used to lubricate the exhaust valve; As the engine working time increases, the steam generated by the high-temperature oxidation of the engine oil will be sucked into the combustion chamber through the crankcase forced ventilation valve for combustion.
10
5
Share

How to Deal with Mice in the Car

Check and confirm whether mice are hiding in the car trunk or in the air ducts. Carefully inspect where the mice entered and see if they are inside the car. If found, drive them out. You should check if the car's interior is damaged and whether the wiring or pipes in the engine area have been compromised. It is recommended to take the car to a car wash for a thorough cleaning or repair. If it is confirmed that the mice did not enter through the doors or by hitching a ride with items, and no mice are found inside the car, then it is necessary to inspect or replace the air intake vent for the external air circulation of the air conditioning system.
5
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.