What causes the electronic parking brake system failure in Haval H9?

1 Answers
HarleyFitz
07/30/25 1:51am
Electronic parking brake failure warning light on indicates a fault in the parking brake switch component or damaged wiring harness between the parking brake switch and the electronic parking module. It is recommended to promptly visit a 4S shop for inspection and repair. Specific solutions for electronic parking brake failures are as follows: Unable to engage the parking brake: When the car's electronic parking brake fails and cannot be used, you can restart the vehicle and try again. If it still doesn't work, go to a repair shop or 4S shop to have professionals check it. Unable to release the parking brake: If the car's electronic parking brake cannot be released, the vehicle cannot move. This situation is generally rare, and you can call for roadside assistance.
Was this review help?
13
3
Share
More Forum Discussions

What are the reasons for the Golf 7 center console screen not lighting up?

Golf 7 center console screen not lighting up reasons are as follows: 1. Poor line contact: It is necessary to promptly check whether the line has a loose connection. If there is, it will naturally cause the center console screen not to light up, just connect the loose part properly. 2. Aging power signal line: You can try to replace it with a new one. If the black screen is resolved, it means that the power signal line is indeed problematic. 3. Module abnormality or design defect: The screen has been used for too long, causing the power supply module to malfunction, not only causing lag but also severe black screen phenomenon. It may also be due to circuit design defects. However, problems like module abnormalities and design defects require inspection and repair at a repair shop or direct replacement.
14
3
Share

Is the Mercedes-Benz E300 wheel hub forged or cast?

Mercedes-Benz E300 wheel hubs are cast. Introduction to automobile wheel hubs: An automobile wheel hub is the rotating part of the tire inner rim connected to the wheel core through pillars, and it is also the metal component mounted on the axle that supports the tire. It is also called a wheel rim, steel rim, or tire ring. Surface treatment processes for automobile wheel hubs: Depending on the characteristics and requirements of different vehicle models, the surface treatment processes for wheel hubs will also vary. They can be divided into painting and electroplating. Maintenance methods for automobile wheel hubs: Avoid using cold water to clean when the wheel hub temperature is high; when the vehicle is in a humid area, the wheel hub should be cleaned frequently to prevent salt from corroding the aluminum surface.
1
3
Share

How often should the timing belt on a Citroen C-Quatre be replaced?

Citroen C-Quatre's timing belt generally needs to be replaced every 90,000 kilometers or 6 years. The relevant details are as follows: 1. The timing belt is a rubber component that can deteriorate over time, affecting its performance and potentially leading to engine failure. The C-Quatre maintenance manual specifies that the timing belt should be replaced every 90,000 kilometers or every six years. 2. The steps for replacing the timing belt are as follows: (1) Remove the outer cover of the timing belt and check the alignment marks on the camshaft. There are alignment holes on both wheels on the cylinder head. (2) Remove the spark plugs and use a welding rod or other rod-like object to rotate the crankshaft until the piston reaches the top dead center position. (3) Secure the camshaft with two 10mm screw rods and mark the two timing wheels to prevent misalignment. (4) Remove the old belt and install the new one.
13
4
Share

What are the main components of an engine in terms of mechanisms and systems?

An engine consists of the crank-connecting rod mechanism, valve mechanism, cooling system, lubrication system, ignition system, fuel supply system, and starting system. An engine is a machine capable of converting other forms of energy into mechanical energy, including internal combustion engines, external combustion engines, jet engines, and electric motors. Introduction to the two main mechanisms: 1. The crank-connecting rod mechanism converts the gas pressure generated after fuel combustion into the rotational torque of the crankshaft through the piston and connecting rod, utilizing the inertia of the flywheel to complete the four auxiliary strokes: intake, compression, power, and exhaust; 2. The valve mechanism opens and closes the intake and exhaust valves in a timely manner according to the engine's working sequence and the requirements of each cylinder's working cycle, allowing the combustible mixture or fresh air to enter the cylinder and expelling the exhaust gases.
1
0
Share

What is the difference between gear oil 220 and 320?

Here is the relevant information about the differences between 220 and 320: 1. The 220 grade is thinner than the 320 grade, while the 320 grade is thicker than the 220 grade. The specific parameter indicators are slightly different. The kinematic viscosity (100°C)/(mm2/s) for the 220 grade is 198~<242, and for the 320 grade, it is 288~<352. Other parameters are basically the same. It is essential to select the appropriate grade according to the equipment's instructions, and they cannot be used interchangeably. 2. The 220 and 320 gear oils refer to medium-load gear oil CKC, representing medium extreme pressure gear oil, generally used in machine equipment such as gearboxes, reducers, turbines, and gear cases. The characteristics of this series of lubricants include good load-carrying capacity and anti-scuffing properties; excellent thermal stability and oxidation stability; good adhesion; and they are free of solvents, asphalt, heavy metals, and chlorine, meeting environmental requirements.
3
3
Share

How Many Liters of Transmission Oil Should Be Added to the Cadillac CT6?

The amount of oil required for different types of engines in the Cadillac CT6 varies, as detailed below: 1. For models with the LSY 2.0T engine, the factory oil capacity is 5.7L, and the capacity when replacing the oil filter is 5.0L. The oil type used for the 2.0T engine is DEXOS1-0W20. 2. For models with the LGW 3.0T engine, the factory oil capacity is 7.67L, and the capacity when replacing the oil filter is 5.7L. The oil type used for the 3.0T engine is DEXOS1-5W30. When selecting oil, please note the following: 1. Use engine oil that meets the dexos1 specification and the correct viscosity grade. 2. Engine oil that meets the dexos1 specification and is certified by SAIC General Motors Co., Ltd. is marked with the dexos1 certification logo. 3. Using oil that meets the dexos1 specification helps protect engine performance.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.