What Causes the Electronic Gear Lever Malfunction in Haval H6?

1 Answers
StLola
07/30/25 5:41am
Haval H6 electronic gear lever malfunction is generally caused by the failure of the gear lever locking mechanism, which cannot be repaired by individuals. It is recommended to contact a 4S shop for repair. The following is a detailed introduction to Haval H6: 1: Body dimensions: The Haval H6 has a body length of 4615mm, width of 1860mm, height of 1720mm, a wheelbase of 2680mm, a fuel tank capacity of 58L, and a curb weight of 1675kg. 2. Power configuration: The front suspension of the Haval H6 is a MacPherson independent suspension, and the rear suspension is a double-wishbone independent suspension. It is equipped with a 1.5T turbocharged engine, with a maximum horsepower of 150PS, a maximum power of 110kW, a maximum torque of 210Nm, and is paired with a 7-speed dual-clutch transmission.
Was this review help?
12
4
Share
More Forum Discussions

Do I Need to Be Present to Renew My Driver's License? Can Someone Else Do It for Me?

Renewing a driver's license does not require the presence of the license holder; it can be done by someone else. The following are the conditions for obtaining a driver's license: Height: Height must meet the requirements for the vehicle type. Vision: No color blindness. Hearing: Normal hearing. Limbs: Both hands must have intact thumbs, and each hand must have at least three other intact fingers. Motor Function: Normal motor function in the upper and lower limbs. Additional information for applying for a driver's license: Photos: Seven one-inch color photos with a white background. Application Fee: Payment can be made in cash, by card, or via bank transfer. ID Copy: A copy of the ID card is required, with both sides copied onto a single sheet of paper. Household Register Copy: For non-local residents, a residence permit is also required.
20
0
Share

What is the reason for Mercedes-Benz indicating that the tire pressure monitoring has stopped working?

Mercedes-Benz indicating that the tire pressure monitoring has stopped working is due to a damaged tire pressure sensor. The tire pressure sensor is used to monitor the tire pressure and is directly installed inside the tire, connected to the tire inflation port. If the tire pressure sensor is damaged by impact while driving, it can also cause the tire pressure warning light to illuminate. For a damaged sensor, the only solution is to replace it with a new component. According to the regulations and requirements of the international GBT2978-2008 standard, the standard tire pressure is 2.4-2.5bar. In winter, the tire pressure should be based on the standard tire pressure of the car tire, with an appropriate increase of about 0.2bar. In summer, the tire pressure can generally be about 0.1bar lower than the standard to avoid tire blowouts due to high temperatures. Tire pressure reset method: First, turn on the ignition switch, press and hold the tire pressure monitoring reset button until you hear a "beep," then release it. The tire pressure monitoring system will store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, completing the tire pressure reset.
13
4
Share

What Are the Benefits of Car Window Tinting?

Car window tinting offers benefits such as blocking ultraviolet rays, reducing heat, and preventing injuries caused by sudden glass shattering. Additionally, it provides privacy protection due to the one-way visibility feature of solar films. It also helps lower air conditioning energy consumption, enhances aesthetics, and to some extent, contributes to fuel savings. Below are the benefits of rear window tinting: 1. Heat and Sun Protection: Tinting effectively blocks infrared rays, reducing heat buildup. 2. UV Protection: Tinting films can block up to 99% of UV rays, preventing skin damage. 3. Safety and Explosion Prevention: The base layer of the film is made of polyester, offering excellent tear and puncture resistance. Combined with the adhesive layer, the film can increase glass strength by 100 times, preventing secondary injuries from accidental glass breakage. 4. Creating a Private Space: After tinting, the interior of the car is not visible from one meter away, ensuring privacy and safety. 5. Reducing Air Conditioning Energy Consumption: Air conditioning energy consumption can be reduced by nearly 15%. The cooling capacity loss from air conditioning can be compensated by the tinting film, instantly lowering the interior temperature and contributing to fuel savings.
9
0
Share

Where is the drain screw located on a motorcycle carburetor?

The drain screw of a motorcycle carburetor is located above the drain tube. A plastic tube is connected below the carburetor, which is the drain tube. There is a screw above the drain tube, and this screw is the carburetor's drain screw. The drain screw functions as a valve—loosening it will release fuel, while tightening it will stop the flow. Impurities or moisture in gasoline can inevitably enter the carburetor through the fuel line, and the air filter may also allow small amounts of dust to enter. These impurities and dust accumulate at the bottom of the carburetor (commonly referred to as the float bowl) and form sediment. This sediment can easily clog the fuel passages in the carburetor and wear down its internal components, negatively affecting the engine's normal operation. The purpose of the drain screw is to flush out these sediments through the waste fuel tube. When draining impurities using the drain screw, you must first turn off the fuel tank valve, then loosen the drain screw. Wait until the gasoline and impurities in the carburetor are completely drained before tightening the screw again. If there is any fuel leakage after tightening the screw, it indicates the presence of impurities between the drain screw and the drain hole. In this case, the screw must be fully removed, and both the screw and the hole must be thoroughly cleaned before retightening the drain screw.
8
0
Share

Can Private Diesel Vehicles Enter Beijing?

Diesel vehicles face restrictions when entering Beijing, with international ones permitted to enter the capital. New heavy-duty diesel vehicles must fully comply with the National Phase V emission standards; non-compliant vehicles are prohibited from being sold or registered in Beijing. The Municipal Environmental Protection Bureau leads the research on the local standard limits for Phase VI vehicle fuel and conducts fuel-vehicle compatibility experiments. Relevant information on vehicle emission standards is as follows: 1. Introduction: Vehicle emission standards regulate the content of harmful gases such as CO (carbon monoxide), HC+NOx (hydrocarbons and nitrogen oxides), and PM (particulates, soot) emitted from vehicle exhaust. 2. Implementation Status: Starting from January 1, 2004, Beijing upgraded its vehicle emission standards from Euro I to Euro II, and by 2008, officially implemented the Euro III standard.
14
2
Share

Can You Get a Driver's License Without a Right Hand?

You cannot get a driver's license without a right hand because it does not meet the physical requirements for the driver's license test. According to Article 12 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses" regarding limbs, both thumbs must be intact, and each hand must have at least three other fingers intact, with normal limb and finger movement functions. Relevant information about the driver's license test is as follows: 1. Introduction: The driver's test is a qualification examination organized by the Vehicle Management Office of the Public Security Bureau. Only by passing the driver's test can one obtain a driver's license and legally operate a motor vehicle. 2. Content: The motor vehicle driver's test is divided into the following subjects: the examination on road traffic safety laws, regulations, and related knowledge (also known as the "theoretical test," referred to as "Subject One"), the examination on field driving skills (commonly known as the "parking test," referred to as "Subject Two"), and the examination on road driving skills and safe and civilized driving knowledge (commonly known as the "road test," referred to as "Subject Three"). The test content and passing standards are uniform nationwide, with corresponding test items specified for different types of vehicles.
18
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.