What Causes the Car to Shake When Accelerating Hard?

1 Answers
StRosalie
07/30/25 12:15am
Car shaking when accelerating hard is caused by: poor combustion, which may be due to low fuel pressure, poor ignition leading to incomplete combustion, or insufficient cylinder pressure resulting in lack of power. The solution is to clean the throttle body and regularly inspect the spark plugs, replacing them when necessary. It is recommended to clean the throttle body every 20,000 to 40,000 kilometers. If the driving environment is harsh, the cleaning interval should be shortened. However, the throttle body should not be over-cleaned, as excessive cleaning can lead to premature failure. Frequent cleaning can gradually remove the special coating inside the throttle body chamber. Without this coating, the chamber becomes more prone to oil buildup, creating a vicious cycle that ultimately leads to failure.
Was this review help?
19
0
Share
More Forum Discussions

How to Drive a BYD Qin?

The BYD Qin has a wheelbase of 2670mm. The fuel tank capacity is 50L. The engine type is a 4-cylinder 1.5T direct fuel injection and electric drive. Open the driver's side door of the BYD Qin. Step on the brake pedal of the BYD Qin to prepare to start the BYD Qin engine. Press the one-button start key of the BYD Qin. Switch the starter button to shift the BYD Qin into engine starter mode.
6
1
Share

What to Do When Rain Gets in Through Open Car Windows?

You can install a rain guard above the car window, allowing you to open the window slightly without letting rain in. However, if the rain is too heavy or the window is opened too wide, rain may still enter. Otherwise, if the rubber seal is not fitted properly, it is likely to leak during rain. After water enters the car, you must remove all the seats and wipe all the wiring harnesses and connectors on the chassis. Then, reinstall everything back in place.
16
3
Share

How to Deal with the Diesel Vehicle Exhaust Light Being On?

Automobile exhaust is the waste gas produced during vehicle use, which not only directly harms human health but also has profound impacts on the environment we live in. Generally, the vehicle malfunction light being on is mostly caused by the fuel emission system. Turn off the vehicle three times and then restart it to observe whether the malfunction light remains on. If it is still on, it is necessary to promptly go to the shop to check the fault code to determine whether it is an engine problem or a sensor malfunction.
7
5
Share

How to Replace the Electronic Parking Brake Button on the Boyue?

Braking, also known as deceleration, refers to the action of stopping or reducing the speed of moving locomotives, vehicles, other transportation tools, or machinery. The general principle of braking is to fix a wheel or disc on the high-speed shaft of the machine, which generates a braking torque under external force. First, adjust the ignition switch to the OK position and connect the fault diagnostic instrument. Then, open the solenoid valve to release the pressure from the wheel cylinder, and finally, open the solenoid valve.
10
1
Share

Which country does SWM belong to?

SWM is an Italian brand that has been acquired by China's Huachen Xinyuan. Its vehicle lineup includes: SWM G01, SWM X7, SWM X3, SWM G05, SWM X2, etc. Taking the Elite Edition SWM X7 as an example, its dimensions are 4710mm in length, 1855mm in width, and 1773mm in height, with a wheelbase of 2750mm. The Elite Edition SWM X7 features a MacPherson independent front suspension and a torsion beam non-independent rear suspension. It is equipped with a 1.5L turbocharged engine delivering a maximum horsepower of 156PS, maximum power of 115kW, and maximum torque of 220Nm, paired with a 6-speed automatic transmission.
3
2
Share

What is the normal cylinder pressure?

6 megapascals, which is 6 kilograms per square centimeter. Imbalanced cylinder pressure can cause engine knocking and loss of vehicle power, and in severe cases, it can directly lead to engine failure. Cylinders can be categorized into reciprocating linear type and reciprocating swing type. Reciprocating linear cylinders are further divided into single-acting cylinders, double-acting cylinders, diaphragm cylinders, and double-impact cylinders, among others. The conditions for testing cylinder pressure are: 1. Ensure the car battery has sufficient charge during testing; 2. The engine temperature should be at a normal level, as excessively high engine temperature can increase the pressure inside the engine cylinder; 3. Remove the vehicle's fuel pump fuse when measuring cylinder pressure; 4. Remove the spark plugs when measuring cylinder pressure.
15
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.