What Causes the Car Anti-Skid Light to Illuminate?

1 Answers
LaManuel
07/30/25 4:40am
The reasons for the car anti-skid light illuminating are: 1. Accidentally pressing the ESP off button; 2. Loose or faulty sensor connectors; 3. Short circuit in the wiring or related fuse blown; 4. Software issues causing poor signal transmission; 5. ABS pump failure. The vehicle anti-skid system operates through the ABS and ASR electronic control units, which calculate and analyze signals from the wheel speed sensors to determine the wheel slip rate and vehicle speed. The electronic control unit then adjusts the throttle opening and brake pressure to regulate the wheel slip rate, preventing the vehicle from skidding during operation.
Was this review help?
12
4
Share
More Forum Discussions

Which Subject is Most Likely to Fail in Driving Test Subject 2?

Parallel parking is the most complex part of the Subject 2 driving test. Here are specific techniques for Subject 2: Drive slowly: Maintaining slow speed is the fundamental rule for Subject 2 practice. Without stalling, keep the vehicle moving as slowly as possible - the slower the better, as this allows sufficient time for each adjustment. Adjust mirrors properly: After entering the vehicle, always adjust the mirrors carefully, which is particularly crucial for parallel parking and perpendicular parking. Master the three-point alignment method: The three points are the driver's eyes, reference points on the vehicle, and reference points on the ground. During Subject 2 operations, you must accurately identify these points and observe carefully to position correctly. Pay attention to vehicle corners: During parallel parking: the front corner may touch outside lines, the rear corner may touch side lines of parking space; during curve driving: front corners may cross lines; during right-angle turns: front corners may cross lines; during perpendicular parking: front corner may touch outside lines or left front corner of parking space, right rear corner may touch right parking space line. Therefore, always monitor the four corners relative to outer boundary lines.
14
0
Share

What Symbol Indicates a Dead Car Battery?

When a car battery is dead, it will display a symbol resembling a battery. Below are some maintenance tips for car batteries: In-car electrical usage: To maintain your car battery, avoid activities like listening to the radio loudly, charging your phone, or using an air pump while the engine is off. Prolonged use of these devices can drain the battery, and frequent depletion significantly reduces its lifespan. Highway driving: Regular highway driving offers many benefits. Not only does it help remove carbon deposits from the vehicle, but it also allows the battery to charge fully. Generally, driving on the highway for over an hour can fully charge the battery, keeping it in optimal condition. Avoid prolonged inactivity: If the car is not used for an extended period, disconnect the battery cables or start the vehicle every two weeks and drive a few dozen kilometers to ensure the battery remains functional. High-power electrical connections: Many modern car accessories, such as car refrigerators, vacuum cleaners, and air pumps, have high instantaneous power demands. Avoid connecting these devices directly to the car battery. Instead, start the vehicle first before connecting any electrical equipment.
13
4
Share

What Causes a Car to Break Down on the Highway?

Specific reasons for a car breaking down on the highway include transmission coasting in neutral, transmission gear grinding and jumping, and fuel pump circuit burnout. Transmission coasting in neutral: Increases friction in the shifting mechanism, damaging the transmission. When coasting in neutral with an automatic transmission, the difference between driving speed and engine speed can lead to insufficient oil pressure in the hydraulic lines, damaging the friction plates inside the automatic transmission, ultimately causing transmission failure and potentially leading to a breakdown. Transmission gear grinding and jumping: For automatic transmissions, shifting into Park without fully depressing the brake pedal. If the brake isn't fully engaged before shifting to Park and turning off the engine, it can impact the transmission gears. Over time, this shortens the transmission's lifespan. For manual transmissions, forcing a gear shift without fully depressing the clutch damages the transmission. Forced shifting encounters resistance from the friction and collision between the rapidly rotating gear teeth, causing significant damage. Fuel pump circuit burnout: Fuel pumps rely on the fuel itself for cooling. If the fuel level is too low, exposing the pump, it may overheat or even burn out the circuit. Prolonged exposure to such conditions can significantly reduce the fuel pump's lifespan.
5
0
Share

Is Speeding a Violation of the Law?

Speeding is a violation of the law because, from the perspective of safe driving behavior, vehicles must not exceed the maximum speed limit set by law or the speed indicated by traffic signs. Specific manifestations of speeding include: Exceeding the maximum speed limit set for the road or the speed indicated by signs; competing with pedestrians at crosswalks; failing to slow down before turning or when passing through intersections; driving too closely to other vehicles, cutting in line, or jamming into traffic; failing to adhere to speed limits on highways; and not reducing speed when driving at night, in hazardous road sections, or under adverse weather conditions such as sandstorms, hail, rain, snow, fog, or icy roads. Penalties for speeding: The penalty for speeding is as follows: exceeding the speed limit by less than 10% results in no fine or demerit points; exceeding the speed limit by 10% to less than 20% incurs a fine and 3 demerit points; exceeding the speed limit by 20% to less than 50% incurs a fine and 3 demerit points; exceeding the speed limit by 50% or more incurs a fine and 6 demerit points, and may also result in the revocation of the driver's license. The amount of the fine varies depending on the extent of the speeding violation.
3
2
Share

What is the engine model of the Lavida?

Lavida has a total of 3 engines. The 1.5L naturally aspirated engine model is EA211DMB, the 1.2L turbocharged engine model is EA211DJN, and the 1.4L turbocharged engine model is EA211DJS. All three engines of the Lavida come from Volkswagen's EA211 engine platform, featuring aluminum cylinder blocks that reduce weight and improve heat dissipation. This results in better fuel economy, lower fuel consumption, and strong power output. The Lavida is a sedan produced by Shanghai Volkswagen, launched in June 2008. While inheriting the dynamic and stylish design language of the A-segment market, the Lavida represents a new design DNA.
12
5
Share

What does speed detection mean?

Automobile speed detection determines whether a vehicle is speeding by calculating its average speed. Specifically, it involves two adjacent monitoring points on the same road section. The speed of the vehicle passing these two points is recorded, and the system then calculates the average speed to determine if the vehicle is exceeding the speed limit. Methods of automobile speed detection: Coil speed detection: Coil speed detection measures speed using induction coils buried underground in the road surface. This method is relatively accurate but requires significant construction effort. Once the road surface is altered, the coils need to be reinstalled. Video speed detection: Video speed detection uses computer analysis of captured footage to determine the vehicle's movement path and behavior, thereby capturing images of traffic violations. This method is not restricted by road conditions and is relatively easy to install, but it is greatly affected by weather. Microwave radar speed detection: Microwave radar speed detection works in conjunction with high-speed cameras to quickly capture images of violating vehicles, using high-speed shutters for evidence collection. Its advantage is the ability to capture images of high-speed vehicles, typically used on highways. Ultrasonic speed detection: Ultrasonic speed detection emits ultrasonic waves through an ultrasonic transmitter and determines the distance based on the time difference of the waves received by the receiver. This method has higher costs and is unsuitable for harsh environments.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.