What Causes the Cadillac to Shake When Accelerating?

What is the working principle of the engine oil pressure sensor?

The working principle of the engine oil pressure sensor is: 1. The amplified pressure signal is connected to the oil pressure gauge through the signal line, changing the current ratio between the two coils inside the oil pressure gauge, thereby indicating the engine's oil pressure; 2. The pressure signal, after voltage and current amplification, is also compared with the alarm voltage set in the alarm circuit. When it falls below the alarm voltage, the alarm circuit outputs an alarm signal and lights up the warning light through the alarm line. The solutions for excessively high engine oil pressure are: 1. Adjust the clearance between the shaft neck and bearing of the pressure lubrication part; 2. Clean the oil pipes and oil passages, and maintain the filter; 3. Select the appropriate oil grade; 4. Replace the oil with the appropriate viscosity; 5. Check and adjust the pressure relief valve on the oil pump test bench to ensure the oil pressure meets the specified requirements.

14

2

Share

Where is the Bluetooth located in the old Corolla?

The Bluetooth in the old Corolla is located in the menu on the central control screen. Here is an introduction to the Corolla: Main advantages: low fuel consumption, comfortable ride, smooth driving, and rich humanized interior configurations. As the best-selling family car, it has 40 million users worldwide, with excellent quality for peace of mind. Exterior: The appearance is moderate and dignified, stable, without any outstanding highlights, making it more suitable for family use. Interior: The overall interior style is simple, the central control panel design is conventional, the seats are spacious and comfortable, the air conditioning effect is good, and the workmanship is excellent. The overall space is sufficient, with spacious front-row space, limited rear-row space, and practical and convenient storage space. Under the trend of increasing dimensions in compact cars, whether it is the latest Corolla or the previous generation Corolla.

12

3

Share

How to Start a Grand Cherokee When the Key Fob Battery is Dead?

The following are the methods to start a Grand Cherokee when the key fob battery is dead: 1. There is a hidden mechanical key inside the remote key fob, locate the mechanical key. 2. Pry open the outer shell of the car door handle to reveal the keyhole. 3. Insert the mechanical key into the keyhole, open the car door, and start the vehicle. Here is some related information: 1. The Jeep Grand Cherokee (Jeep) is a classic model launched by Chrysler, inheriting the pure pedigree of the Jeep brand. It features a classic exterior design, outstanding off-road capability, excellent highway handling performance, and comprehensive safety features, pioneering the high-end off-road vehicle market. 2. In April 2007, the all-new Jeep Grand Cherokee, with significant improvements and upgrades in all aspects, landed in China. It won widespread acclaim for its outstanding off-road capability and remarkable highway handling performance. The Grand Cherokee 3.0 model is equipped with the Uconnect dual LCD intelligent human-machine interaction system. The 8.4-inch LCD central control system integrates 3D real-time navigation, Bluetooth communication, entertainment, temperature control, and other functions, along with touch control and Chinese voice control systems. 3. The instrument panel center integrates a 7-inch color LCD display, which can display more than 100 types of information through the quick control buttons on the steering wheel. 4. Jeep's famous product during World War II later introduced the civilian version CJ Jeep. In 1987, the new model was renamed Wrangler. In 1997, an improved version was launched, restoring the traditional round headlights. The exterior design was not significantly modified, but the drag coefficient was reduced from 0.63 to 0.55. The chassis suspension system replaced leaf springs with hydraulic springs (Quadra-coil), among other improvements.

20

2

Share

Where is the cabin air filter located in the Haval H2S?

Haval H2S's cabin air filter is located inside the glove compartment in front of the front passenger seat. The replacement method for the cabin air filter is as follows: 1. Use a screwdriver to remove the screws on the top and bottom of the glove compartment; 2. Press the plastic clips on both sides of the glove compartment to remove it; 3. After removing the glove compartment, you can see the cabin air filter housing; 4. Press the plastic clip on the cabin air filter housing to remove it; 5. Replace with a new cabin air filter, then reassemble the glove compartment in reverse order of disassembly. The Haval H2S is a compact SUV with body dimensions of 4195mm in length, 1772mm in width, and 1638mm in height, with a wheelbase of 2550mm. It is equipped with a 1.5-liter turbocharged engine.

8

3

Share

How many seconds to restart the engine after stalling in Subject 2 without penalty?

Stalling in Subject 2 will result in penalty points, and there is no mention of how many seconds you have to restart to avoid penalty. After stalling in Subject 2, there is no need to pull the handbrake. At this time, you should press both the brake and clutch to prevent the car from rolling back, then quickly shift the gear back to neutral, and turn the key to restart. Subject 2, also known as the small road test, is the abbreviation of the field driving skill test subject. Its purpose is to master the basic driving operation essentials, have the basic ability to control the vehicle, proficiently master the basic methods of field and in-field road driving, have the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and be able to accurately control the vehicle's driving position, speed and route.

4

3

Share

What are the main failure modes of closed soft-tooth-surface gear transmission?

The main failure modes of closed soft-tooth-surface gear transmission are: 1. Tooth breakage: Tooth breakage usually occurs in two situations, one is fatigue breakage caused by repeated bending stress and stress concentration, and the other is overload breakage caused by sudden severe overload or impact load; 2. Plastic deformation: Generally occurs on tooth surfaces with low hardness, but can also appear on high-hardness gears under heavy loads; 3. Pitting corrosion: During gear operation, under the repeated action of alternating contact stress at the meshing point, small cracks will form on the tooth surface near the pitch line. As these cracks expand, they will cause small pieces of metal to peel off, a phenomenon known as pitting corrosion; 4. Tooth surface adhesion: For high-speed and heavy-load gear transmissions, tooth surface adhesion is prone to occur. Additionally, low-speed and heavy-load heavy-duty gear transmissions can also experience tooth surface adhesion failure, known as cold adhesion.

3

2

Share

What Causes the Cadillac to Shake When Accelerating?

What is the working principle of the engine oil pressure sensor?

Where is the Bluetooth located in the old Corolla?

How to Start a Grand Cherokee When the Key Fob Battery is Dead?

Where is the cabin air filter located in the Haval H2S?

How many seconds to restart the engine after stalling in Subject 2 without penalty?

What are the main failure modes of closed soft-tooth-surface gear transmission?

How to Determine a Car's Production Date Through the Glass?

What do the letters in license plates represent?

What is the wading depth of the Lexus ES?

What Causes Throttle Vibration?