What Causes the Buick Excelle to Shake?

3 Answers
StEloise
07/23/25 5:20pm
The reasons for the Buick Excelle shaking are: 1. Engine misfire; 2. Worn or loose engine mounts; 3. Carbon buildup issues; 4. Fuel system malfunction. The Buick Excelle's body dimensions are: length 4609mm, width 1798mm, height 1486mm, with a wheelbase of 2640mm and a fuel tank capacity of 44 liters. The Buick Excelle is equipped with a 1.3T turbocharged engine, delivering a maximum horsepower of 163 hp, a maximum power of 120 kW, and a maximum power speed of 5500 rpm. It is paired with a 6-speed automatic transmission. The front suspension type is MacPherson independent suspension, and the rear suspension type is multi-link independent suspension.
Was this review help?
19
3
Share
VonHolden
08/10/25 1:03pm
When driving my Buick Excelle, I've experienced shaking. Experience tells me this is usually caused by excessive carbon buildup in the engine. After long-term use, the intake valves and fuel injectors get clogged, leading to uneven air-fuel mixture and jerky idling. Or it could be worn-out spark plugs with abnormal ignition causing severe engine shudder during acceleration. Tire imbalance is another common issue - you'll feel the car wobbling at high speeds like riding a boat. If suspension components like shock absorbers leak, the shaking becomes more noticeable when going over speed bumps or turning corners. To prevent trouble, I regularly clean the throttle body, replace spark plugs, and check tire balance. When noticing vibrations, I immediately visit the repair shop for inspection - better fix small issues early than wait for major failures that cost more.
Was this review help?
11
3
Share
Expand All
Leo
09/22/25 7:28am
I recall the days of driving the Buick Excelle, where the main cause of shaking was often excessive carbon buildup in the engine system, blocking components and causing incomplete combustion that led to fluctuations. Worn spark plugs were another culprit; when the electrode gap widened and ignition failed, the car would tremble. Tire issues shouldn’t be underestimated—imbalance or uneven wear affects smooth driving, especially on long trips when it feels exhausting. Aging suspension and failed shock absorbers can cause unstable body movement, accompanied by annoying creaking sounds. Safety first—I recommend prioritizing these simpler checks, such as inspecting spark plug conditions and adjusting tire pressure within limits, while developing a monthly inspection habit to save on repair costs.
Was this review help?
20
1
Share
Expand All
More Forum Discussions

How long can the renewal of an expired driver's license be delayed?

Driver's license renewal after expiration can be delayed for a maximum of three years. If the license has been expired for more than one year but less than three years, the renewal can be processed by passing the subject one exam. Regulations on the expiration of a driver's license: If the license has been expired for less than one year, it can be renewed normally; if it has been expired for more than one year but less than three years, the license will be revoked, but it can be renewed by passing the subject one exam; if it has been expired for more than three years, the license will become invalid and cannot be renewed. Penalties for driving with an expired license: Driving a motor vehicle with an expired license is prohibited and will be treated as driving without a license. If the driver's license has been expired for less than one year, the driver can renew it at any time, but driving on the road will result in a fine of 200 yuan. If the driver's license has been expired for more than one year without renewal, the traffic management department will revoke it according to the law. If the expiration period is less than three years, the driver must retake and pass the subject one exam to restore the driving qualification. Driving on the road during this period will result in a fine ranging from 200 to 2000 yuan. If the driver's license has been expired for more than three years, it will be permanently revoked. To drive again, the driver must retake the driver's license exam. Otherwise, driving on the road will be treated as driving without a license, resulting in a fine of 2000 yuan and administrative detention for up to 15 days.
12
2
Share

Is the Highlander 2.0T Engine Imported?

The Highlander 2.0T engine is a domestically produced engine that utilizes Toyota's production technology and is manufactured at Toyota's Kyushu plant. The Highlander 2.0T engine model is the 8AR-FTS, with a maximum power output of 162KW, a maximum torque of 350Nm, and a maximum horsepower of 220. For daily maintenance of the Highlander 2.0T engine, the following methods can be employed: Use lubricating oil of the appropriate quality grade. For gasoline engines, select SD--SF grade gasoline engine oil based on the additional equipment in the intake and exhaust systems and usage conditions. For diesel engines, choose CB--CD grade diesel engine oil according to mechanical load, ensuring the selected standard meets or exceeds the manufacturer's requirements. Regularly replace the engine oil and filter. The quality of any lubricating oil will degrade over time with use. After a certain mileage, its performance deteriorates, leading to various engine issues. To prevent malfunctions, change the oil periodically based on usage conditions and maintain an appropriate oil level. As oil passes through the fine pores of the filter, solid particles and viscous substances accumulate in the filter. If the filter becomes clogged and oil cannot pass through, it may rupture the filter element or force open the safety valve, allowing oil to bypass through the relief valve and carry contaminants back to the lubrication areas, accelerating engine wear and increasing internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gases, acids, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls. These mix with metal particles from component wear to form sludge. In small amounts, the sludge remains suspended in the oil, but in larger quantities, it precipitates, clogging filters and oil passages, making engine lubrication difficult and causing wear. Periodically use a radiator cleaner to flush the radiator. Removing rust and scale deposits not only ensures the engine operates smoothly but also extends the overall lifespan of both the radiator and the engine.
16
4
Share

Why is the tire pressure low on rainy days?

Reasons for low tire pressure on rainy days: If the tire is damaged or the valve seal is not tight, causing air leakage, it will lead to a decrease in tire pressure; If the tire rim is deformed, it will affect the sealing performance, resulting in lower tire pressure; If the vehicle frequently exceeds the specified load weight, the rear wheels will experience different stress compared to the front wheels. Hazards of excessive tire pressure: The friction and adhesion of the tire will decrease, affecting braking performance; It can cause steering wheel vibration and deviation, reducing driving comfort; It accelerates the localized wear of the tread pattern in the center of the tire, shortening the tire's lifespan; It increases the vibration of the vehicle body, indirectly affecting the lifespan of other components; It causes excessive stretching and deformation of the tire cords, reducing the elasticity of the tire body and increasing the load on the vehicle during driving; It decreases puncture resistance. When encountering sharp objects like nails or glass on the road, the tire is more easily punctured, and impacts can cause internal cracks and blowouts, leading to tire bursts. Hazards of insufficient tire pressure: The friction coefficient with the road surface increases, leading to higher fuel consumption; It makes the steering wheel heavy and prone to deviation, which are factors detrimental to driving safety; It increases the movement of various parts of the tire, causing abnormal heating due to excessive rolling; It reduces the functionality of the cords and rubber, leading to delamination or cord breakage, and excessive friction with the rim, causing damage and abnormal wear at the bead area; The friction between the tire and the ground increases exponentially, causing a sharp rise in tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under such conditions may lead to tire bursts; It increases the deformation of the tire body, making the sidewalls prone to cracks and causing flexing movements, leading to excessive heat, accelerating rubber aging, cord fatigue, and breakage, while also increasing the tire's contact area with the ground and accelerating shoulder wear.
13
2
Share

What Causes the ABS Yellow Light to Stay On?

ABS light can illuminate in various states, and different states have different causes and solutions. The details are as follows: State 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by mud, sludge, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and wheel slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt on the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Loose connections between system lines or poor contact in the ABS relay can cause signal issues, leading to system failure. Solution: Check the line connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. The ABS warning light turns off as the engine speed increases and voltage rises. The ABS system power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer malfunction. Solution: Loosen the grounding screw of the hydraulic valve body, then retighten it. Clean the contact surface if necessary. Check if the connector gap has widened. Replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals. Incorrect tire or wheel rim specifications may also be a factor. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, and use a finger to push the brake switch linkage down fully. Release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary. If the ABS warning light is on, it is recommended not to continue driving. An illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may skid uncontrollably, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks.
9
5
Share

Can a temporary ID card be used to schedule the written test for driving license?

A temporary ID card can be used to schedule the exam. The admission ticket and other documents are handled by the driving school, which will distribute them during the exam. Electronic ID cards cannot be used for the exam. If you don't have an ID card, you can apply for a temporary one. A temporary ID card has the same validity as a formal ID card. According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," the written test (Subject 1) can be taken twice on the same day. If you fail the first attempt, you can retake it for free. If you fail the second attempt, the Subject 1 test will be terminated, and you can only reschedule the exam after ten days. The Subject 1 test consists of 100 questions, including single-choice and true/false questions, with each question worth 1 point and a total score of 100. If you answer 11 questions incorrectly during the exam, the system will automatically submit the test and end the session. The Subject 1 test is computer-based and lasts 45 minutes. Subject 1 test content: Regulations on driving licenses and motor vehicle management; Road traffic conditions and regulations; Road traffic safety violations and penalties; Road traffic accident handling regulations; Basic knowledge of motor vehicles; Local regulations; Knowledge of braking systems and safety devices for large and medium-sized passenger and freight vehicles; Specialized knowledge for wheeled self-propelled machinery, trams, and trolleybuses. Subject 1 exam precautions: Candidates should pay attention to their attire during the exam. Slippers are not allowed, and electronic devices and bags are prohibited in the exam room. Bring your ID card and queue to enter the waiting hall. Observe the precautions and procedures on the large screen, and store personal belongings in lockers before entering the exam room. Upon entering, the identity verification station will assign a seat. After finding your seat, begin the exam. Ensure the camera is aligned with you and follow exam discipline. If you fail the first attempt, you can retake it the same day. If you fail again, you must pay to reschedule. After the exam, queue to collect your score report and sign it. Unsigned reports are invalid. There is no limit to the number of times you can schedule the Subject 1 exam. Each subject can be taken once, and if you fail, you can retake it once. If you do not take the retest or fail the retest, the exam will be terminated, and you must reschedule. For Subject 2 and Subject 3, there are only five exam attempts. Subject 2 and Subject 3 exams can be rescheduled after ten days. If you fail the Subject 3 safe driving knowledge test, the previously passed road driving skills test results remain valid. The driving test consists of three subjects: Subject 1, Subject 2, and Subject 3. Subject 1 refers to the road traffic safety laws, regulations, and related knowledge test; Subject 2 refers to the field driving skills test; Subject 3 is divided into two parts: road driving skills and safe driving knowledge. The safe driving knowledge test is conducted after Subject 3, so it is commonly referred to as Subject 4. However, the official term (as per the Ministry of Public Security Order No. 123) does not include "Subject 4."
1
1
Share

Where to Use Turn Signals in Subject 2 of the Driving Test?

There are a total of 6 instances where turn signals are required in Subject 2: When starting the vehicle, turn on the left turn signal; When starting on a slope, turn on the left turn signal; During parallel parking, turn on the right turn signal when the vehicle passes the parking spot and stops 30 cm from the curb before preparing to reverse; Before shifting into reverse gear during parallel parking, turn on the left turn signal because the steering wheel will be turned fully to the right during reversing, causing the front of the car to shift left; Before exiting the parking spot during parallel parking, shift into drive gear and turn on the left turn signal, then turn it off promptly after exiting; When entering the right-angle turn area, turn on the left turn signal and turn it off promptly after completing the turn. Penalties for incorrect use of turn signals are as follows: Failing to use or incorrectly using turn signals before starting, turning, changing lanes, overtaking, or parking results in a 10-point deduction. Using turn signals for less than 3 seconds before starting, turning, changing lanes, overtaking, or parking results in a 10-point deduction. The full score for Subject 2 is 100 points, with evaluation criteria set for failing, deducting 20 points, deducting 10 points, and deducting 5 points. The test is considered passed under the following conditions: ① For applicants of large buses, tractors, city buses, medium buses, and large trucks, a score of 90 or above is required; ② For other vehicle types, a score of 80 or above is required. The test items for small cars (C1, C2) include reversing into a parking space, parallel parking, stopping and starting on a slope (canceled for C2), right-angle turns, and S-curves (five mandatory items; some regions include a sixth item: highway toll collection). The test items for large vehicles (A1, A2, A3, B1, B2) include pole parking, stopping and starting on a slope, parallel parking, driving over a single-plank bridge, S-curves, right-angle turns, passing through a narrow gate, navigating continuous obstacles, driving on bumpy roads, making a U-turn in a narrow lane, as well as simulated highway driving, continuous sharp turns on mountain roads, tunnels, rain (fog) conditions, slippery roads, and emergency handling.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.