···
Log in / Register

What Causes the Air Conditioning in Buick Excelle to Stop Cooling?

4 Answers
EllianaLynn
07/29/25 7:51pm

The reasons why the air conditioning in Buick Excelle suddenly stops cooling: 1. Dirty air conditioning filter: No air or reduced airflow from the air conditioning, requiring inspection of whether the air filter is dirty, whether the blower can operate normally, and whether the air conditioning flap motor can switch properly. 2. Lack of Freon in the air conditioning system: A shortage of Freon in the system necessitates checking for leaks. After confirming and repairing, Freon should be replenished to the standard level. 3. Engine cooling system failure: A dirty radiator condenser or engine cooling system malfunction leading to excessively high water temperature, such as a non-functioning cooling fan, resulting in poor heat dissipation from the radiator and condenser. 4. Incorrect sensor data: Faulty data from sensors like the air conditioning pressure sensor or evaporator box sensor can prevent the air conditioning system from adjusting correctly. 5. Damaged air conditioning compressor adjustment solenoid valve: Issues like a damaged solenoid valve, clutch, or internal components of the air conditioning compressor. 6. Air conditioning system wiring or control unit failure: Problems caused by faulty wiring or control unit in the air conditioning system. When the car air conditioning stops cooling, it is advisable to choose a relatively professional repair facility for inspection and repair.

Was this review help?
11
3
Share
VonHannah
08/14/25 3:30pm

My Buick Excelle's air conditioner wasn't cooling properly recently, and after inspection, it was found that the refrigerant was insufficient, which might be caused by a leak. Additionally, the compressor could wear out or seize up, affecting cooling performance; electrical faults like blown fuses or damaged relays are also common; a dirty air filter can block airflow, reducing cooling efficiency; system leaks such as aging pipes or seals may also cause refrigerant loss. It's recommended to first check if the AC pipes feel cold - if the temperature is normal, it indicates the system is running but with low cooling efficiency; driving without AC in summer heat can be dangerous, so have it professionally inspected promptly, and avoid randomly recharging refrigerant to prevent more severe component damage.

Was this review help?
6
0
Share
Expand All
SpencerRose
10/15/25 7:45am

Last year, my Excelle's air conditioning suddenly stopped cooling. The repair shop found it was just a blown fuse, a very simple issue. Other possible causes include compressor failure preventing refrigerant circulation; a dirty condenser or damage from gravel hindering heat dissipation; loose wiring connectors or unstable voltage causing control module errors; or the AC switch being stuck or malfunctioning. You can try turning on the AC to listen for the compressor sound - if it's silent and not working, it's likely an electrical issue. To prolong your AC's lifespan, avoid parking in direct sunlight, and address any abnormalities early to save money and ensure safety.

Was this review help?
11
3
Share
Expand All
SanJoshua
11/28/25 8:37am

My Buick Excelle's air conditioning suddenly has poor cooling. After checking common causes: low refrigerant pressure due to leaks; compressor wear or loose belts; clogged filters restricting airflow; unstable voltage damaging components; aging system pipe connections causing leaks. As someone who frequently drives to pick up my kids, I prioritize safety – no AC in summer heat can easily lead to heatstroke, so I must immediately turn off the engine for inspection and avoid forcing the drive; regularly replacing filters prevents clogs, small habits can avoid big troubles.

Was this review help?
2
5
Share
Expand All
More Forum Discussions

How early can a B2 driver's license annual review be conducted?

Annual reviews cannot be conducted in advance. Below is relevant information about annual reviews: 1. Concept: Also known as motor vehicle inspection. The inspection items and scope vary depending on the usage nature of the motor vehicle. 2. Time: For small cars and blue-license minivans, within the first six years after new vehicle registration, an inspection is required every two years; after six years, it becomes an annual inspection; after ten years, it's an annual inspection, and after fifteen years, it's twice a year. For trucks, after registration, an annual inspection is required; after ten years, it's twice a year. The documents required for vehicle annual inspection include: the vehicle's driving license, valid compulsory insurance policy, and vehicle and vessel usage tax.
3
5
Share

What are the four basic types of car insurance?

Vehicle insurance four basic types refer to vehicle damage insurance, third-party liability insurance, no-deductible insurance, and passenger insurance. The following is a detailed introduction: 1. Vehicle damage insurance: Vehicle damage insurance means that if the vehicle owner causes total or partial loss of the vehicle due to an accident during driving, the insurer shall compensate according to the insurance contract. 2. Third-party liability insurance: Third-party liability insurance refers to the economic liability that the insured or their permitted driver should bear according to the law when an accident occurs during the use of the insured vehicle, causing personal injury or death or direct property damage to a third party, and the insurance company is responsible for compensation. 3. No-deductible insurance: If an accident within the scope of insurance liability occurs, resulting in vehicle loss or third-party liability compensation, the insurer shall be responsible for compensation according to the amount stipulated in the "Terms" for compensation. 4. Passenger insurance: Refers to during the insurance period, the insured and their permitted legal driver, in the process of using the insured vehicle, if an accident occurs causing personal injury or death to the personnel on the insured vehicle, the economic compensation liability that should be borne by the insured according to the law.
16
5
Share

What is the maximum wading depth of the Haval H9?

The maximum wading depth of the Haval H9 is 700mm. The wading depth of the Haval H9 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Haval H9 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before wading, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in water, which could cause severe damage due to water ingestion. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow it at a low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or the wheels and doors of other vehicles as reference points to estimate water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the tire height or the engine's air intake, do not proceed and choose an alternative route instead.
16
0
Share

Should the Buick GL6 Use 92 or 95 Octane Gasoline?

According to the official vehicle manual recommendation, the Buick GL6 should use 92 octane gasoline. In addition to checking the appropriate gasoline grade in the vehicle manual, you can also find it on the fuel tank cap, which will also indicate the recommended octane. Generally, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92 octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95 octane gasoline. However, with the application of new technologies, the compression ratio alone cannot determine the gasoline grade. High-compression engines can also be tuned to use lower-octane gasoline because, besides the compression ratio, other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline octane number, the higher the octane value and the better the anti-knock performance. 92 octane gasoline contains 92% isooctane and 8% n-heptane, while 95 octane gasoline contains 95% isooctane and 5% n-heptane. If the Buick GL6 occasionally uses the wrong gasoline grade, simply switch back to the correct octane after the tank is empty. However, prolonged use of the wrong gasoline grade can have the following effects: For vehicles recommended for low-octane gasoline, using a higher octane will not cause damage, but the increased octane value may alter the fuel's ignition point, leading to delayed combustion in the engine. This reduces the engine's power output and thermal efficiency, resulting in poorer performance. For vehicles recommended for high-octane gasoline, using a lower octane can cause engine knocking. The significantly lower octane value reduces the fuel's ignition point, causing premature ignition during the compression stroke. If the fuel ignites before the spark plug fires, resistance occurs during the upward stroke. This resistance makes the engine run very unevenly. Mild knocking may only increase noise without significant engine damage, but noticeable knocking indicates severe engine conditions. The vibrations not only affect driving stability but can also cause abnormal wear on the pistons and cylinders, potentially leading to cylinder scoring in severe cases.
20
4
Share

How Many Kilometers Can the First Maintenance Be Exceeded?

First maintenance can be exceeded by 500 kilometers. The following is an introduction to the first maintenance: 1. Concept: The first maintenance of a car refers to the initial maintenance, generally at 5000 kilometers/6 months. 2. Notes: The engine has a break-in period with a new car. Different brands and models of cars are equipped with different engines, some of which use special technology and have strict requirements for engine oil. Some engines have special materials and high precision, resulting in relatively less wear. In addition to changing the engine oil and oil filter, the first maintenance also includes a comprehensive inspection and diagnosis of the vehicle's condition and usage. Usually, the first maintenance is free of charge.
4
1
Share

What is the difference between FAW Haima and Haima?

FAW Haima and Haima differ in that Haima is a Chinese automobile manufacturer, while FAW Haima is a Japanese automobile manufacturer. Here are the relevant introductions: 1. Haima Automobile: The logo of Haima Automobile features an abstract falcon shape embedded in a circle symbolizing the sun, representing "the rising sun and the soaring roc," which embodies the corporate image of Haima Automobile's upward striving and determined ambition to soar. 2. FAW Haima: FAW Haima Automobile Co., Ltd. is located in Jinpan Industrial Development Zone, Haikou City, covering an area of 1 million square meters. After more than ten years of construction, Haima Automobile has established excellent asset structures and advanced management systems, built leading domestic production lines for automobile stamping, welding, painting, and assembly processes, and established shared development and supporting platforms and marketing networks with strategic partners. It is a large-scale passenger car production enterprise designated by the state.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.