What Causes the Abnormal Noise When Steering While Braking?

1 Answers
SanNicole
07/29/25 5:12pm
The causes of abnormal noise when steering while braking are as follows: 1. Abnormal noise from disc brakes. Characteristics: When the vehicle is driven at low speed on a flat road, intermittent and irregular abnormal noise occurs at the wheel axle. The noise slightly intensifies as the speed increases, but does not change when going uphill, downhill, or turning. The noise worsens when driving on uneven roads and reduces or disappears when the brake pedal is pressed. 2. The brake shoe support plate, damping spring plate, or guide plate of the disc brake may be damaged, deformed, or detached, increasing the clearance between the brake shoe and the caliper support frame, causing them to collide and produce noise. Deformed parts can be repaired at a repair shop, and detached parts should be replaced. 3. Abnormal noise from the front suspension ball joint. When the vehicle is driven in low gear on bumpy roads, continuous abnormal noise occurs at the front axle. The worse the road quality, the louder the noise, which intensifies with increasing speed. After parking, forcefully shaking the front of the vehicle will produce abnormal noise. Since the ball joint seat is a sealed structure and cannot be disassembled, it can only be replaced.
Was this review help?
3
4
Share
More Forum Discussions

How to Handle Traffic Jams on an Uphill Slope with an Automatic Transmission?

Here are the specific operation methods for dealing with traffic jams on an uphill slope with an automatic transmission: 1. When stuck in traffic on a slope, you can gradually release the brake pedal to allow the car to creep forward at idle speed. Since the vehicle is on an uphill slope, the idle speed will be slower than on flat ground. Wait patiently for a while, and the idle speed will increase. 2. If the uphill angle is relatively large, the vehicle's idle speed might not be sufficient, leading to the car rolling backward. In this case, you should gently press the accelerator pedal immediately after releasing the brake to help the car move forward as much as possible. Avoid pressing too hard to prevent the car from suddenly lurching forward.
11
2
Share

What does AVM mean in cars?

AVM is a panoramic imaging system. Introduction to AVM: The full name is Around View Monitor. It captures images through multiple ultra-wide-angle fisheye lenses, then processes the data to correct distortion and stitch the images together, forming a surrounding view. Primarily used in automotive systems, it provides drivers with a top-down view around the vehicle, eliminating blind spots and offering effective visual assistance during parking. Features of AVM: Currently, various panoramic monitoring imaging systems are developed based on the AVM technology proposed by Nissan. The panoramic parking assist system can provide drivers with a real-time 360-degree bird's-eye view of the vehicle's surroundings, allowing drivers to park easily by observing the real-time video images.
7
4
Share

What Causes a Heavy Car Steering Wheel?

There are several reasons why a car's steering wheel may feel heavy: 1. Dirty power steering fluid. This situation is similar to how dirty engine oil can affect engine power and performance. Dirty power steering fluid can cause the steering wheel to become increasingly heavy, and insufficient power steering fluid can also make the steering wheel feel heavier. 2. If the car has electric power steering, check whether the fuse is blown or if there are any open circuits or short circuits to ground in the wiring. Repeatedly turning the steering wheel while stationary or at low speeds places a significant load on the power steering system, which can easily cause the steering gear to overheat and enter a protective mode, making the steering feel heavy. It will return to normal after cooling down, which is a normal phenomenon.
11
2
Share

What to Do When White Paint Turns Yellow?

White car paint turning yellow can be addressed with the following solutions: 1. Car washing. Visit a roadside car wash with standardized procedures, as a good washing method can significantly preserve the paint's gloss. 2. Sun protection. Applying a transparent paint protection film can completely shield the paint from air and UV rays, offering the most thorough protection. Alternatively, purchasing a car cover and using it when the car is parked outdoors is advisable, with an underground parking space being even better. 3. Polishing. Yellowing of the car paint refers to the yellowing of the outermost clear coat. Since the base coat is covered by the clear coat and not exposed to air or UV rays, polishing can temporarily improve the yellowing issue to some extent. However, frequent polishing is not recommended as it can alter the thickness of the paint.
13
1
Share

What are the dimensions of the Honda WR-V?

The body dimensions of the Honda CR-V are 4585mm in length, 1855mm in width, and 1679mm in height, with a wheelbase of 2660mm. The Honda CR-V is a model under the Honda brand, featuring a fuel tank capacity of 53 liters and a body structure of a 5-door, 5-seat SUV. Below are the relevant details about the Honda CR-V: 1. The Honda CR-V is equipped with a 1.5T turbocharged engine, delivering a maximum horsepower of 193 HP, a maximum power of 142 kW, and a maximum torque of 243 Nm, paired with a 6-speed manual transmission. 2. The Honda CR-V utilizes a MacPherson strut independent suspension and a multi-link independent suspension, with a monocoque body structure.
3
0
Share

What does it mean when the battery light turns red?

The above two models of tires are interchangeable. Tire Introduction: Tires are circular elastic rubber products assembled on various vehicles or machinery to roll on the ground. They are usually mounted on metal rims to support the vehicle body, cushion external impacts, ensure contact with the road surface, and maintain the vehicle's driving performance. Tires are often used under complex and demanding conditions, enduring various deformations, loads, forces, and high and low temperatures during operation. Therefore, they must possess high load-bearing capacity, traction performance, and cushioning performance. Additionally, they are required to have high wear resistance and flex resistance, as well as low rolling resistance and heat generation. Principles for Changing Tire Specifications: The upgraded tires should have the same or similar total diameter as the original tires.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.