···
Log in / Register

What Causes the Abnormal Noise When Accelerating a Car?

4 Answers
MacVera
07/29/25 11:02am

Reasons for abnormal noise when accelerating a car: 1. Excessive clearance or damage in internal engine components such as pistons, valves, gears, and camshaft bearings; 2. Loose or insecure connections in areas like door panels, glove compartments, air vents, and center console panels causing friction; 3. Rusty brake discs or noise caused by trapped sand and debris; 4. Loose shock absorbers or connecting components in the suspension system. Engine maintenance methods include: 1. Regularly changing engine oil and oil filters; 2. Periodically using high-efficiency rapid cleaning agents for the lubrication system to clean the crankcase and maintain internal engine cleanliness; 3. Regular maintenance of the PCV system, removing contaminants around the PCV valve to ensure proper crankcase ventilation.

Was this review help?
1
5
Share
MaxDella
08/13/25 5:07pm

Last time I filled up my car, I suddenly heard a buzzing sound from the fuel tank area, like a beehive, which really startled me. It's most likely due to an aging fuel pump—this component sits inside the tank and pumps fuel, and over time, its impeller can wear out. Another possibility is an air leak in the fuel line, causing the pump to draw air and make strange noises. Remember to check the rubber seal on the fuel filler cap; if it's aged and leaking, it can alter the tank's pressure. If the noise happens every time you refuel, you should head to the repair shop ASAP—otherwise, you might end up stranded when the pump fails. That happened to me once, and replacing the pump cost me nearly two thousand yuan.

Was this review help?
16
1
Share
Expand All
JustinDella
10/07/25 8:37am

Speaking of abnormal noises during acceleration, my car once experienced a buzzing vibration from the chassis. The mechanic said it was most likely due to a cracked exhaust pipe, where high-temperature exhaust gases escaping caused a whistling sound, especially noticeable during acceleration when the engine load increases. A stuck pressure relief valve inside the fuel tank can also produce a hissing sound, similar to a slow tire leak. You can pop the hood to listen for bearing noises from the pulley, but avoid touching components near the fuel tank. It's advisable to note the type of noise: sharp sounds may indicate sealing issues, while dull vibrations often point to exhaust pipe weld failures. Don't ignore it like I did—the crack expanded, costing me over 800 bucks to fix.

Was this review help?
2
3
Share
Expand All
KendraRose
11/21/25 3:13am

The most common cause of abnormal noise near the fuel tank is a fuel pump issue, especially in vehicles with over 80,000 kilometers. Worn fuel pump blades can produce a whining sound like a broken fan, which becomes more noticeable under increased load during acceleration. Additionally, a leaking exhaust pipe gasket due to aging can create a hissing noise. I once mistook it for something scraping under the car, but upon lifting the trunk liner, I found that rodents had chewed through the fuel pump wiring harness, causing a short circuit that led to abnormal solenoid valve noise. A simple fix is to replace and secure the wiring harness with new zip ties. For safety, always turn off the engine and check for gasoline odors whenever abnormal noises are heard.

Was this review help?
17
4
Share
Expand All
More Forum Discussions

Is Wheel Balancing Necessary After Patching a Rear Tire?

Wheel balancing is necessary after patching a rear tire, especially if the tire was removed for repair or if the patched area is relatively large. The specific reasons are as follows: Wheel balancing directly affects driving safety. If balancing is not performed after patching, the wheel may not rotate smoothly, leading to issues such as vehicle vibration and steering wheel shaking while driving. This is particularly noticeable at high speeds, where the vibration becomes more pronounced with increased speed. Symptoms of poor rear wheel balance include: 1. Vehicle vibration: Generally, poor rear wheel balance can cause vibration, though it may not be as obvious as with the front wheels. 2. Abnormal tire wear: Wheel balancing corrects uneven mass distribution. At high speeds, uneven mass distribution can become more pronounced, leading to irregular tire wear. 3. Increased fuel consumption: Poor wheel balance can increase driving resistance, thereby raising fuel consumption.
6
0
Share

Can I Take the Manual Transmission Test After Passing the Automatic Transmission Test?

You can take the manual transmission test after passing the automatic transmission test, but you will need to retake all the exams. Below is some relevant information about automatic transmissions: 1. Automatic Principle: The engine's power is transmitted through the gearbox, which is also a key factor affecting fuel consumption. Generally, automatic transmissions consume about 10% more fuel than manual transmissions. Whether manual or automatic, more gears usually mean better fuel efficiency. 2. Driving Tips: For manual transmission vehicles, it's recommended to shift gears at higher RPMs. Engines are designed to operate optimally at higher RPMs, with parameters like dynamic balance and rotational inertia set for high-speed performance. Prolonged operation at non-optimal RPMs increases internal component load and wear, leading to frequent vibrations and knocking, which can reduce engine lifespan. Shifting at 3000 RPM ensures the post-shift RPM stays around 2300, keeping the engine within a healthy operating range.
3
5
Share

Should You Engage the Gear or Press the Clutch First Before Driving?

Before driving, you should engage the gear first and then press the clutch. Here are some key points to note when operating a manual transmission car: 1. Pressing: Master the pressing of the clutch pedal through practice to develop a good habit—press it all the way down and release it slowly. 2. Releasing: Coordinate the throttle and clutch. When starting, engage first gear, slowly release the clutch, and apply the throttle in the semi-clutch state. Only release the clutch completely after the car starts moving. 3. Shifting: Master the timing of shifting. Shift gears when the engine speed is around 2000 RPM—first press the throttle and then the clutch to prevent the clutch from being forced to disengage. Then shift gears. The shifting sequence must be first gear, second gear, third gear, fourth gear, and fifth gear. Skipping gears is not recommended. Downshift according to the vehicle speed.
5
0
Share

What is the normal pressure range for car air conditioning?

Under normal operating conditions of the air conditioning system, the low pressure typically ranges between 1.0—2.5 bar, while the high pressure ranges between 15—18 bar. Additional information: 1. Normal pressure range: The standard range for car air conditioning pressure is generally that the high pressure should not exceed 1.7 MPa or fall below 1.3 MPa, while the low pressure should normally be no lower than 1.15 MPa and no higher than 1.25 MPa. If the low pressure is higher or lower than this normal range, it indicates improper adjustment of the expansion valve. 2. Evaporator wear: The car air conditioning evaporator, fan, and other components are often in a closed and dark state, creating a high-temperature and humid internal environment. Impurities, dust, bacteria, and viruses from the air enter the air conditioning system and combine with condensed water, clogging components such as the evaporator. Over time, this leads to the accumulation of dirt, nicotine, mold, fungi, and other contaminants.
4
2
Share

How often should the transmission fluid be changed for a Toyota Reiz?

Toyota Reiz requires transmission fluid replacement every 80,000 kilometers. The Reiz is a sporty B-segment sedan under Toyota, featuring rear-wheel drive. Its front suspension employs a double-wishbone independent suspension, while the rear utilizes a multi-link independent suspension. The multi-link independent suspension is an evolution of the double-wishbone design, where the two wishbones are replaced with separate links. The Reiz's headlights feature a sharper design, giving the front fascia a resemblance to the Lexus ES model. The taillights adopt an irregular contour, with the high waistline extending to the rear and integrating with the trunk, ultimately merging with the ducktail spoiler. This creates smooth side profiles while visually enhancing the vehicle's substantial presence.
3
0
Share

How to reset the one-button start maintenance reminder for Geely Vision S1?

Turn off the ignition switch, press the left-right directional button on the right side of the multifunction steering wheel, then press the one-button start to power on the vehicle. After five seconds, release the button, and the dashboard will display a reset prompt. Press and hold the SET button for more than five seconds, then press the MODE button, and finally turn off the vehicle. Below is some relevant information about the Geely Vision S1: 1. Introduction to the Geely Vision S1: The Geely Vision S1 is the second strategic model from Geely Auto in the crossover SUV market. 2. Core values: The letter "S" in the name Geely Vision S1 represents the five core values of the product: Sharp (stylish design), Smart (convenient connectivity), Safe (comprehensive protection), Satisfying (comfortable experience), and Sporty (dynamic driving pleasure).
11
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.